D-Link DAP-1520 user manual

To set up your D-Link DAP-1520, follow these steps:
1. Connect your DAP-1520 to a power outlet near your existing wireless router.
. Use a computer or mobile device and connect to the default Wi-Fi network of the DAP-1520. The default Wi-Fi network name (SSID) should be "DAP-1520". The default Wi-Fi password can be found on the label on the back of the device.
3. Open a web browser and type "dlinkap.local" or "192.168.0.50" (without quotes) in the address bar. Press Enter.
4. You will be prompted to set a new password for the DAP-1520. Set a strong password and click Next.
5. You will be presented with a list of available Wi-Fi networks. Select the network you want to extend and click Next.
6. Enter the Wi-Fi password of the selected network and click Next.
7. On the next screen, you can change the extended Wi-Fi network name and password if desired. Otherwise, click Next.
8. Review the settings and click Finish to complete the setup.
9. The DAP-1520 will restart and may take a few minutes to apply the changes. Once it's ready, you can unplug it and move it to a location where you want to extend your Wi-Fi network coverage.
Note: If the above steps don't work, you can try accessing the setup wizard by typing "192.168.0.50" (without quotes) directly into the address bar of your web browser and pressing Enter.

To determine if your D-Link Wi-Fi extender is working properly, follow these steps:
1. Power on your Wi-Fi extender and wait for it to boot up. Make sure it is properly connected to a power source and turned on.
2. Locate the Wi-Fi indicator lights on the extender. These lights usually indicate the status of the connection.
3. The initial power indicator should turn solid after booting up successfully. This indicates that your extender has power.
4. Look for the Wi-Fi signal indicator light. Once the extender has established a connection to your existing Wi-Fi network, this light should turn solid or blink.
5. Connect to the extended Wi-Fi network on your computer or mobile device. On your device, search for available Wi-Fi networks and look for the network name (SSID) of your extender. Connect to it using the provided Wi-Fi network key or password.
6. Once connected, try accessing the internet or using any online service. If your device successfully connects to the internet and works well, it means your D-Link Wi-Fi extender is functioning correctly.
7. Additionally, you can check the signal strength of your extended Wi-Fi network. Move around your home or office and see if the signal bars appear strong and consistent on your device's network connection indicator.
If you continue to experience Wi-Fi issues or face difficulties connecting to the extender, refer to the user manual of your specific D-Link model for troubleshooting steps or contact D-Link customer support for assistance.

To reset a D-Link DAP-1520 Wi-Fi extender, you can follow these steps:
1. Locate the "Reset" button on the device. It is usually a small hole labeled "Reset" on the back or bottom of the extender.
2. Using a small, pointed object like a paperclip or pin, press and hold the Reset button for about 10 seconds. You may need to use some force to depress the button.
3. After holding the button for the specified time, release it. The device will then restart, and the LED lights may flash indicating the reset process.
4. Wait for the extender to finish booting up. This may take a few minutes. The LED lights should stabilize once the reset is complete.
5. The DAP-1520 has now been reset to its factory default settings. You can now reconfigure it by connecting to the default Wi-Fi network name and setting it up again using the D-Link setup wizard or app.
Note: Resetting the extender will erase any personalized settings, including Wi-Fi network names, passwords, and configurations. You will need to set up the extender from scratch after the reset.

There could be several reasons why your D-Link Wi-Fi extender (DAP-1520) is not working. Here are some troubleshooting steps you can try:
1. Check the power: Make sure the extender is properly powered on and connected to a power source.
2. Placement: Ensure that your extender is placed within the range of your existing Wi-Fi network. It should ideally be in a central location between your router and the area with a weak signal.
3. Signal interference: Check for any potential sources of signal interference, such as microwave ovens, cordless phones, or other electronic devices. Try to move the extender away from such devices.
4. Resetting: If you have previously configured the extender, try resetting it to factory settings. Use a pin or paperclip to press and hold the reset button on the device for about 10 seconds. This will restore the extender to its default settings.
5. Wi-Fi settings: Ensure that you have correctly configured the Wi-Fi settings of your extender to match your existing network. Make sure you are connecting to the correct network name (SSID) and entering the correct password.
6. Firmware update: Check if there is a firmware update available for your extender. Visit the D-Link support website and download the latest firmware for your specific model. Upgrade the firmware following the manufacturer's instructions.
7. Compatibility: Ensure that your extender is compatible with your router and network specifications. Some extenders may not work well with certain routers or frequencies. Check the compatibility information provided by D-Link or contact their support for assistance.
8. Restarting: Sometimes a simple restart of both your router and extender can help resolve connectivity issues. Power off both devices, wait for a few seconds, then power them back on.
If, after trying these steps, your D-Link WiFi extender still does not work, it may be beneficial to contact D-Link customer support for further assistance.