Beko WTK72011W user manual

To program your Beko washing machine, follow these steps:
1. Turn on the washing machine by pressing the power button.
. Check if the water supply is connected and turned on.
3. Sort your laundry according to fabric type, color, and care instructions.
4. Open the washing machine door and load the laundry evenly in the drum. Avoid overloading the machine.
5. Close the door properly to ensure it is locked.
6. Turn the program dial to select the desired wash program. The available programs will vary depending on your model, but common options include cotton, synthetics, delicates, wool, quick wash, etc.
7. If needed, adjust the temperature and spin speed using the respective buttons or dials. The appropriate settings depend on your laundry's fabric and care requirements.
8. Optionally, you can add detergent, fabric softener, or any other laundry additives to the dispenser drawers. Follow the recommended dosage for your load size and water hardness.
9. Press the start/pause button to commence the wash cycle. You may also need to press the start button twice, or a similar combination to begin the program, depending on your model.
10. The machine will fill with water and initiate the wash cycle. You can monitor the remaining time on the digital display or progress indicators if available.
11. If necessary, you can pause or cancel the program during the wash cycle by pressing the appropriate button. Follow the manufacturer's instructions for your specific model.
12. After completing the wash and rinse cycles, the machine will automatically go into the spinning phase to remove excess water. The spin speed may depend on the program selected or can be manually adjusted.
13. Once the washing and spinning phases are complete, the machine will display "End" or another indication that the cycle is finished.
14. Open the door and remove your laundry.
15. Clean the filter and drum of the washing machine regularly to maintain its performance and prolong its lifespan.
Remember to refer to your Beko washing machine's user manual for specific instructions and details tailored to your appliance model.

There could be several reasons why your Beko washing machine is stuck on a cycle:
1. Control board malfunction: The control board is the brain of your washing machine and controls various operations, including the cycle selection. If the control board is faulty or damaged, it may not register your commands to change the cycle or stop the current cycle.
2. Mechanical issue: There may be a mechanical issue with the timer or motor of the washing machine. This can prevent the machine from advancing to the next cycle or stopping the current one.
3. Door interlock problem: Many modern washing machines have a door interlock mechanism that locks the door during a cycle. If the door interlock is faulty or the sensor does not detect that the door is properly closed, the machine may not proceed with a new cycle or allow you to stop the current one.
4. Water supply issues: If the washing machine is not getting enough water or the water pressure is too low, it may not proceed to the next cycle. This is a safety measure to ensure that the machine operates efficiently and does not damage the clothes.
5. Electronic glitch: Sometimes, electronic glitches or power surges can cause the washing machine's programming to get stuck. In such cases, a simple power reset may solve the issue.
It is recommended to consult the user manual of your specific Beko washing machine model for troubleshooting steps. If the issue persists, it may be necessary to contact a professional technician or the manufacturer's customer service for further assistance.

Yes, there is a reset button on most Beko washing machines. The location of the reset button may vary depending on the specific model of the washing machine. It is usually located on the control panel or inside the detergent drawer.

To perform a factory reset on a Beko WTK72011W washing machine, follow these steps:
1. Ensure that the washing machine is disconnected from the power supply.
. Wait for a few minutes to allow any residual power to dissipate.
3. Reconnect the washing machine to the power supply.
4. Press and hold the "Start/Stop" button and the "Prewash" button simultaneously.
5. While holding these buttons, turn the washing machine's program selector knob to the farthest left position (usually marked as "Off" or "Reset").
6. Keep holding the buttons until the digital display or indicator lights start to flash.
7. Release the buttons and wait for the washing machine to complete the reset process.
8. Once the reset is finished, the washing machine will be restored to its original factory settings.
It's important to note that the exact steps might vary slightly depending on the model of your Beko washing machine. If you're unsure about any step or encounter any issues, it's recommended to refer to the user manual specific to your model or contact Beko customer support for guidance.