Summary of the content on the page No. 1
Summary of the content on the page No. 2
Table of Contents Safety Instructions .................................................................................................. 3 Introduction ............................................................................................................ 3 Description of Air Filtration System How the Air Purifier Works ..................................................................... 4 Air Purifier Components ......................................................................... 4 D
Summary of the content on the page No. 3
SAFETY INSTRUCTIONS IMPORTANT! READ ALL INSTRUCTIONS BEFORE USING THIS AIR PURIFIER. 1. This air purifier is designed for use on a flat level floor and may not work properly on an uneven floor. ALWAYS place the air purifier on a firm level floor. ALWAYS place the air purifier at least six (6) inches away from walls and heat sources such as stoves, radiators, or heaters. 2. Place the air purifier in an area that is out of the reach of children. 3. Before using the air purifier, extend the cord an
Summary of the content on the page No. 4
RESET DAY PROG RST FILT TIME AUTO DISP OFF ON Description of Air Filtration System ® How the QuietFlo HEPA Air Purifier System Works As the air is pulled into the purifier, the activated carbon pre-filter absorbs odors and catches large particles. Then, the air travels through the HEPA filter where the smaller particles are collected. Finally, the clean purified air is released back into the room. Dust & Irritants Pollen & Allergens Odors Bacteria Pet Hair & Dander Carbon True HEPA Filter Pre-Fi
Summary of the content on the page No. 5
Description of Air Filtration System Display and Control Keys The display and control keys allow for easy operation of the air purifier. ON/OFF: Turns the unit on and off. PROGRAM: Allows you to enter program mode and define user programs. (User UP/DOWN KEYS (+/-): Adjusts the blower programming on pg. 15.) speed and changes values in clock setting and programming modes. DAY/TIME: Used to set the day and time. (Setting day and time on pg. 13.) DISPLAY: Selects the clock, pre-filter, or fil
Summary of the content on the page No. 6
Summary of the content on the page No. 7
Summary of the content on the page No. 8
Operation Remote Operation For your convenience, a remote control is provided with this air purifier. The remote may be used to turn the air purifier on or off and adjust the fan speed. Operating the Air Purifier with the remote: 1. Install two AAA batteries (UM-4 or IEC R03 or equivalent). Refer to the graphics in the battery compartment for proper orientation of the batteries. 2. To use the remote, point it at the air purifier, then press and release the appropriate key. The key functions are
Summary of the content on the page No. 9
Operation Display Modes Your air purifier has 3 display modes – Clock Display, Pre-Filter Display, and Filter Dis- play. When the unit is running, the display also provides additional information about the settings of the air purifier. The features for each mode and how to change modes is de- scribed below. Clock Display: The default mode of the unit is the Clock Display. In this mode, the day indicator, time, and AM/PM indicator will be lit. If military time has been chosen (See Setting Day and
Summary of the content on the page No. 10
Operation Manual and Auto Operating Modes Your Hunter Air Purifier has two distinct operating modes – Manual and Auto. The Manual Mode allows you to override the control programs that have been set and to hold the settings until you adjust them. In Manual Mode, the automatic programs are not active. You select whether the unit is on or off and choose the blower speed. In Auto Mode, your air purifier is capable of running 4 separate programs for the weekdays and an additional 4 programs for the w
Summary of the content on the page No. 11
Summary of the content on the page No. 12
Operation Filter Run-Time Counters The pre-filter and filter are critical to the proper operation of the air purifier. To help you know when to change the filters, your Hunter Air Purifier has Filter Run-Time Counters that will monitor the number of hours your filters have been in use. Although the exact life of the filters depends on the environment, the table below gives typical usage times of the filters. Table 2: Typical Usage Times of the Filters Filter Type Typical Usage Activated Carbon P
Summary of the content on the page No. 13
Programming Setting Day and Time Setting the correct day and time allows the programs to work effectively and provides a clock for your reference. Although the instructions for setting the day and time are listed under Initial Operation, they are repeated below for your convenience. Adjusting Day and Time: (For example, Wednesday at 3:45 pm) 1. To set the day or time, press the DAY/TIME key. All DAY display features except the day and time will go blank TIME and the hour will flash. Fig. 19 2. U
Summary of the content on the page No. 14
Programming NOTES: • The clock flashes when the time has not been set. • At any time while you are setting the Day/Time, you can press the PROGRAM key to toggle between AM/PM format and military time format. •To quickly exit the Day/Time setting mode, you can press the DISPLAY key or wait 15 seconds without pressing any keys. •The time displayed will be frozen in Day/Time setting mode; however, the internal clock is still running. If no value is changed, then the frozen time will be replaced by
Summary of the content on the page No. 15
Programming User Programming User programming allows you to set when the air purifier is on and what blower speed to use. You may define up to 4 programs for the weekdays and up to 4 programs for the week- end. Before starting the programming process, first you should determine what times and blower speeds will best fit your needs. Use the charts below to organize and record the programs that you desire. Use a pencil so you can revise your records each time you change the programs. Table 4 WEEKD
Summary of the content on the page No. 16
Summary of the content on the page No. 17
Programming Reviewing Programs You may want to review the programs to confirm that the settings are still acceptable. The following steps show you how to review the programs. To review programs: 1. With the air purifier On, press and hold the PROGRAM key. After 2 seconds, the PROG display will advance through the 4 programs for weekdays and then the 4 pro- grams for the weekend. You must hold the PROGRAM key as the display re- views the programs. 2. After viewing all programs, the display will r
Summary of the content on the page No. 18
Programming Resetting the Air Purifier In the unusual situation that the unit or the display is exhibiting erratic behavior, you may want to reset the air purifier. Since you will lose all of your programmed settings when the unit is reset, you should consult the Troubleshooting section (pg. 22) of the manual to re- solve the problem before using the Reset Feature. When the unit is reset, the clock, day of the week, and programs will default to their factory settings and the unit will turn off.
Summary of the content on the page No. 19
Air Purifier Maintenance Cleaning Your Air Purifier Proper maintenance of your Hunter Air Purifier will help ensure years of trouble free service. Follow these steps to properly maintain your air purifier: 1. Approximately every 90 days, the outside of the unit should be cleaned with a soft, damp cloth. 2. If needed, the front grill can be removed from the unit and cleaned with soapy water. Simply remove the pre-filter before exposing the grill to water. 3. Follow the instructions in Changing th
Summary of the content on the page No. 20
Air Purifier Maintenance 6. Install the grill back onto the unit. First, line up the tabs on the bottom of the grill with the openings on the purifier base and then push the top of the grill forward until it is closed. 7. Plug in the air purifier. NOTE: This unit will not oper- ate unless the grill is in the correct position. The display will read “door” if the grill is not attached properly. 8. Finally, reset the pre-filter counter by pressing the DISP DISPLAY key until the pre-filter counter i
