Summary of the content on the page No. 1
ELECTRIC HOB
MEH 631
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
Keep this instruction book for future
reference and ensure it is passed on to any
new owner.
3
4
2
1
6
5
7
1. Hob Top
Any electrical work required to install
2. Normal Hotplate - 1500 W -180 mm dia.
this hob should be carried out by a
3. Normal Hotplate - 1000 W - 145 mm dia. qualified electrician or competent
4. Rapid Hotplate - 2000 W - 180 mm dia. person, in accordance with the
5. Rapi
Summary of the content on the page No. 2
Important Safety Information You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 950950 Installation This hob must be installed by qualified has cooled. personnel, according to the Children can also injure themselves by manufacturer's instructions and to the pulling pans or pots off the hob. relevant British Standards. Remove all packaging before using the During Use hob. This hob is intended for dome
Summary of the content on the page No. 3
This hob should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. Environmental Information After installation, please dispose of the packaging with due regard to safety and the environment. When disposing of an old appliance, make it unusable, by cutting off the cable. The symbol on the product or on Guide to Use the instructions its packaging indicates that this product The following symbols will be found in the may not b
Summary of the content on the page No. 4
Hints and Tips Operation Saucepans for use on solid plates should Electric Hotplates have several characteristics: To switch on a hotplate, turn the relevant They should be fairly heavy duty control knob anticlockwise to the required heat They should fit the heat area exactly, or setting. be slightly larger for efficient use, NEVER The control knob is numbered 1 - 6 smaller. They should have a flat base to ensure OFF 0 good contact with the plate. MINIMUM 1 To keep food warm This is particula
Summary of the content on the page No. 5
Maintenance Something not and Cleaning working Before any maintenance or cleaning If the appliance is not working correctly, please carry out the following checks, before can be carried out, you must DISCONNECT the hob from the contacting your local Service Force Centre. electricity supply. IMPORTANT: If you call out an engineer to a The hob is best cleaned whilst it is still fault listed below, or to repair a fault caused by warm, as spillage can be removed incorrect use or installation, a cha
Summary of the content on the page No. 6
Instructions for the Installer This hob must be installed by qualified personnel to the relevant British Standards. - The manufacturer will not accept liability, should the following instructions or any of the other safety instructions incorporated in this book be ignored. Engineers technical data Overall dimensions Cut out dimensions Width: 580 mm. Width: 550 mm. Depth: 500 mm. Depth: 470 mm. Heating elements Ratings Normal front left hotplate Ø 180 mm 1500 W Normal back left hotplate Ø 145 mm
Summary of the content on the page No. 7
50 mm 100 mm 50 mm 600 mm Important safety requirements This hob must be installed in accordance with INSTALLATION GUIDANCE INSTRUCTIONS the IEE Wiring Regulations (Current Edition). CLEARANCES REQUIRED WHEN FITTING THE HOB Detailed recommendations are contained in WITHOUT A COOKER HOOD ABOVE the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions. Location This hob has been registered as a "Class X" appliance according to Fire Risk R
Summary of the content on the page No. 8
ON/OFF SWITCH 1 2 Building In ON/OFF SWITCH Building over a cupboard or FLEX OUTLET drawer FLEX OUTLET If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the FO 0763 FO 0764 electrical connection to the hob as shown in diagrams 1 and 2. Dimensions are 3 given in mm. Building over a kitchen unit with door Proper arrangements must be taken in
Summary of the content on the page No. 9
Electrical connections The hob should be connected to a double This hob is designed to be connected to a pole switch with a minimum gap of 3 mm. 230V 50Hz AC electrical supply. between the switch contacts and of a type Before switching on, make sure the suitable for the required load in compliance electricity supply voltage is the same as that with the current electric regulations. The indicated on the hob rating plate. The rating switch should be sited within 2m of the hob plate is located on t
Summary of the content on the page No. 10
Service and Spare Parts Guarantee Conditions If you require spare parts or an engineer Home visits are made between 8.30am and contact your local Service Force Centre by 5.30pm Monday to Friday. Visits may be telephoning: available outside these hours, in which case a premium will be charged. 08705 929 929 Exclusions Your call will be routed to the Service Centre This guarantee does not cover: covering your post code area. The *Damage or calls resulting from addresses of Service Force Centres
Summary of the content on the page No. 11
11
Summary of the content on the page No. 12
www.electrolux.com 35676-3003 05/06 Grafiche MDM - Forlì
