Summary of the content on the page No. 1
INSTALLATION
SEALED GAS COOKTOPS
Models: MGC5430 & MGC5536
MANUAL
403 WEST FOURTH STREET, NORTH NEWTON, IA 50208
IMPORTANT: Dimensions Shown in Both Inches and Centimeters.
IMPORTANT: Be sure the appliance being installed is equipped for the gas to be supplied. Refer to serial plate on
underside of burner box for this information. Do not attempt to convert this appliance for use with a gas other than the type
specified.
DIMENSIONS
30 MODEL
inches cm
A281/2 + 1/16 72.4 + 0.2
B 19 15/16 + 1/16
Summary of the content on the page No. 2
Location Of Your Maytag Important Preparation Appliance Suggestions Locate this appliance away from combustible materials 1. Chamfer all exposed edges of decorative laminate to such as window curtains and combustible wall prevent damage from chipping. decorations. 2. Radiuscornersofcutoutand fileto insuresmooth edgesand prevent cornercracking. Recommend Minimum horizontal clearance between the edge of the 1/4or3/8diameterdrill in each corner. appliance and combustible construction extend
Summary of the content on the page No. 3
Check the cooktop serial plate to see if the cooktop is All supply piping, except as noted, should use common approved for installation in mobile homes and/or National Pipe Thread (N.P.T.). For all pipe connections recreational park trailers. Serial plate is located on the use an approved pipe joint compound resistant to the bottom of the unit. action of LP gas. CAUTION: Warranty is void on Maytag equipment If approved, the following items are applicable: installed other than as recommended by m
Summary of the content on the page No. 4
Connecting Appliance To IMPORTANT Gas Supply Apply a non-corrosive leak detection fluid to all joints and A QUALIFIED SERVICE TECHNICIAN OR GAS fittings in the gas connection between the supply line APPLIANCE INSTALLER MUST MAKE THE GAS shut-off valve and the cooktop. Include gas fittings and SUPPLY CONNECTION. Leak testing of the joints in the cooktop if connections were disturbed appliance shall be conducted by the installer during installation. Check for leaks! Bubbles appearing according to
Summary of the content on the page No. 5
2. IF THIS UNIT WILL HAVE AMAYTAG MODEL ILLUSTRATIVEGASSUPPLYPIPING MEW6500orMEW5500SERIES ELECTRICWALL (WALL OVENINSTALLEDBELOW 30COOKTOP) OVENINSTALLEDBELOW THISCOOKTOP. NOTE 1: This appliance and its gas and electrical supply sources must be installed before the wall oven is installed. See illustration (Electrical Wiring Information - page 7; figure 6) for recommended electrical supply source locations. (3/8N.P.T.) NOTE 2: It may be necessary to extend gas supply piping for this applian
Summary of the content on the page No. 6
Alternative Piping Methods To Pressure Testing The appliance must be isolated from the gas supply Connect Appliance To Gas Supply piping system by closing its individual manual shut-off A TRAINED SERVICE TECHNICIAN OR GAS valve during any pressure testing of the gas supply piping APPLIANCE INSTALLER MUST MAKE THE GAS system at test pressures equal to or less than 1/2 pounds SUPPLY CONNECTION. Leak testing of the per square inch (3.5 kPa). appliance shall be conducted by the installer This applia
Summary of the content on the page No. 7
Electrical Wiring Information This appliance is equipped with a grounded type power can be located as is convenient in this left wall or in the cord. A grounded outlet must be provided. It is corresponding right wall. recommended, for convenience, the outlet be located In planning any installation, note that the free length of (with reference to figure 6) as in A or B, below: this appliance’s power cord, extending beyond a point 3-3/4 (9.53 cm) left of the nominal center of the rear wall A. If
Summary of the content on the page No. 8
Installation Of LP Orifice Spud Converting Appliance For Use With LP Gas Propane conversion is to be performed by a MAYTAG AUTHORIZED SERVICER (or other qualified agency) in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage. The qualified agency performing this work assumes responsibility for this conversion. Electricalpowerandgasmustbeturnedoff prio
Summary of the content on the page No. 9
B.INVERT CAP INAPPLIANCE PRESSURE REGULATOR (See figure 11) With the appliance installed, the appliance regulator After adjusting the screw the burner should produce a should be located as shown in figure 3, 4 or 5. stable, steady blue flame of minimum size. The setting should be checked by turning knob from high to low several times without extinguishing the flame. CONVERSION OF APPLIANCE PRESSURE REGULATOR This operation will automatically provide the proper flame size at medium setting. After
Summary of the content on the page No. 10
4BURNERMODEL(30WIDE) To Convert Appliance For Use 1.10 1.55 With Natural Gas Electricalpowerandgasmustbeturnedoff priortoconversion. If this appliance has been converted for use with LP gas, each of the following modifications must be performed to convert the unit back to natural gas. A.REPLACE ALL ORIFICE SPUDS. 1. Perform Steps 1 and 2 on page 8. 2. Perform Step 3 on page 8. 3. For Step 4: Locate the brass natural gas orifice 1.55 spuds that were originally installed in this appliance before
Summary of the content on the page No. 11
Burner Performance shutters. When operating properly, burners should CAUTION: Never cover control knobs or surrounding produce clearly defined, even blue flames. If the flames control surface with utensils, towels, or other objects. have yellow tips or are hazy and otherwise appear to Never obstruct free air passage past the control knobs. have insufficient air, obtain the services of a qualified The knob openings have been sized to properly control air service technician. Some yellow tipping on
Summary of the content on the page No. 12
Holding Unit Down To COUNTERTOP Countertop IMPORTANT To hold the cooktop to the counter top, two hold down brackets have been provided. Utilize the hold-down brackets, one on the left and one on the right side of unit to secure the unit to the counter top. Additional hold-down BURNER BOX brackets may be added to the front and/or rear. Contact your dealer or authorized service agency. HOLD-DOWN Position the cooktop in the cutout opening. BRACKET Open cabinet doors and locate screw holes at right
Summary of the content on the page No. 13
SUPERFICIES PARA COCINAR MANUALDE DE GAS SELLADAS INSTALACIÓN 403 WEST FOURTH STREET, NORTH NEWTON, IA 50208 Modelos: MGC5430 y MGC5536 IMPORTANTE: Las dimensiones aparecen en pulgadas y centímetros. IMPORTANTE: Asegúrese de que el electrodoméstico que se instalará esté equipado con el gas que se surtirá. Consulte la placa de datos que se encuentra en la parte inferior de la caja del quemador para obtener esa información. No trate de convertir este electrodoméstico para usar otro tipo de gas q
Summary of the content on the page No. 14
Ubicación de su Sugerencias importantes de electrodoméstico Maytag preparación Coloque este electrodoméstico alejado de materiales 1. Alise todos los bordes expuestos del laminado combustibles como cortinas de ventanas y decoraciones decorativo para evitar que se quiebren. de pared. 2. Redondeelasesquinasdel recorteylímelaspara evitarqueseestrellen. Serecomiendaunabroca El espacio libre horizontal mínimo entre el borde del de1/4o3/8dediámetro en cadaesquina. electrodoméstico y la constru
Summary of the content on the page No. 15
Revise la placa de datos de la superficie para cocinar Toda la tubería de suministro, excepto cuando se indica, para ver si esta última está aprobada para instalarse en debe ser de tipo común de rosca NPT (National Pipe casas móviles y/o en remolques de recreación. La placa Thread). Use en todas las conexiones de tubería un de datos se encuentra localizada en la parte inferior de la compuesto aprobado para uniones de tubería que sea unidad. resistente a la acción del gas LP. Si está aprobada, se
Summary of the content on the page No. 16
Conexión del electrodoméstico IMPORTANTE al suministro de gas Aplique un líquido de detección de fugas que sea LA CONEXIÓN DEL SUMINISTRO DE GAS DEBE anticorrosivo en todas las uniones y los accesorios de REALIZARLA UN TÉCNICO CALIFICADO O UN la conexión de gas entre la válvula de cierre de la tubería INSTALADOR DE ELECTRODOMÉSTICOS DE GAS. de suministro y la superficie para cocinar. Incluya los Las pruebas de fugas de gas debe realizarlas el accesorios de gas y las uniones de la superficie para
Summary of the content on the page No. 17
2. SI SE INSTALARÁUNHORNO ELÉCTRICO DE ILUSTRACIÓNDE LATUBERÍADE SUMINISTRO PAREDMAYTAG DE LASERIE MEW6500O DE GAS MEW5500DEBAJO DE ESTASUPERFICIE PARA (HORNODEPAREDINSTALADODEBAJODEUNA SUPERFICIEPARACOCINARDE30) COCINAR. NOTA1: Deberá instalarse este electrodoméstico y sus fuentes de suministro de gas y eléctrico antes de instalar CAJADELQUEMADOR el horno de pared. Vea la ilustración (Información de (PARTE POSTERIOR DEL ELECTRODOMÉSTICO) alambrado eléctrico — en la página 7, figura 6) para
Summary of the content on the page No. 18
Métodos alternativos de tubería Pruebas de presión El electrodoméstico debe aislarse del sistema de la para conectar el electrodoméstico tubería de suministro de gas cerrando la válvula de cierre al suministro de gas manual independiente durante las pruebas de presión del sistema de la tubería de suministro de gas a presiones de UN TÉCNICO CAPACITADO O UN INSTALADOR DE prueba iguales o menores a 1/2 libras por pulgada ELECTRODOMÉSTICOS DEBE REALIZAR LA cuadrada (3,5 kPa). CONEXIÓN DEL SUMINISTRO
Summary of the content on the page No. 19
Información de alambrado eléctrico Este electrodoméstico está equipado con un cordón izquierdo). El orificio (que no se muestra en la figura 4) eléctrico con conexión a tierra. Debe proporcionarse un puede ubicarse según sea conveniente en esta pared tomacorriente conectado a tierra. Se recomienda, por izquierda o en la pared derecha correspondiente. comodidad, que el tomacorriente se encuentre (con Al planear cualquier instalación, observe que la longitud referencia a la figura 6) como en el pu
Summary of the content on the page No. 20
Instalación de la copa de orificio LP Conversión del electrodoméstico para usarse con gas LP 0,91 0,64 0,91 ADVERTENCIA La conversión a gas propano debe realizarla un TÉCNICO AUTORIZADO DE MAYTAG (u otra agencia calificada) de acuerdo con las instrucciones del fabricante y con todos los códigos y requisitos de las autoridades correspondientes. El no seguir las instrucciones podría causar lesiones graves y daños materiales. La agencia calificada que realice el trabajo asume toda la responsabilida
