Summary of the content on the page No. 1
INSTALLATION
SEALED GAS COOKTOPS
Models: JGC9430 & JGC9536
MANUAL
403 WEST FOURTH STREET, NORTH NEWTON, IA 50208
IMPORTANT: Dimensions Shown in Both Inches and Centimeters.
IMPORTANT: Be sure the appliance being installed is equipped for the gas to be supplied. Refer to serial plate on
underside of burner box for this information. Do not attempt to convert this appliance for use with a gas other than the type
specified.
DIMENSIONS
30 MODEL
inches cm
A281/2 + 1/16 72.4 + 0.2
B 19 15/16 + 1/16
Summary of the content on the page No. 2
Location Of Your Jenn-Air Important Preparation Appliance Suggestions Locate this appliance away from combustible materials 1. Chamfer all exposed edges of decorative laminate to such as window curtains and combustible wall prevent damage from chipping. decorations. 2. Radiuscornersofcutoutand fileto insuresmooth edgesand prevent cornercracking. Recommend Minimum horizontal clearance between the edge of the 1/4or3/8diameterdrill in each corner. appliance and combustible construction exte
Summary of the content on the page No. 3
Check the cooktop serial plate to see if the cooktop is All supply piping, except as noted, should use common approved for installation in mobile homes and/or National Pipe Thread (N.P.T.). For all pipe connections recreational park trailers. Serial plate is located on the use an approved pipe joint compound resistant to the bottom of the unit. action of LP gas. If approved, the following items are applicable: CAUTION: Warranty is void on Jenn-Air equipment installed other than as recommended by
Summary of the content on the page No. 4
Connecting Appliance To Gas Supply A QUALIFIED SERVICEMAN OR GAS APPLIANCE INSTALLER MUST MAKE THE GAS SUPPLY IMPORTANT CONNECTION. Leak testing of the appliance shall Apply a non-corrosive leak detection fluid to all joints and be conducted by the installer according to the fittings in the gas connection between the supply line instructions given. shut-off valve and the cooktop. Include gas fittings and Gas supply piping MUST conform to all local, joints in the cooktop if connections were distu
Summary of the content on the page No. 5
2. IF THIS UNIT WILL HAVE AJENN-AIRMODEL ILLUSTRATIVEGASSUPPLYPIPING JJW8530, JJW9530, W30400P, orJJW8130 (WALL OVEN INSTALLED BELOW 30 COOKTOP) ELECTRICWALL OVENINSTALLEDBELOW THIS COOKTOP. NOTE 1: This appliance and its gas and electrical supply sources must be installed before the wall oven is installed. See illustration (Electrical Wiring Information - page 7; figure 6) for recommended electrical supply source (3/8N.P.T.) locations. NOTE 2: It may be necessary to extend gas supply piping f
Summary of the content on the page No. 6
Alternative Piping Methods To Pressure Testing The appliance must be isolated from the gas supply Connect Appliance To Gas Supply piping system by closing its individual manual shut-off A QUALIFIED SERVICEMAN OR GAS APPLIANCE valve during any pressure testing of the gas supply piping INSTALLER MUST MAKE THE GAS SUPPLY system at test pressures equal to or less than 1/2 PSIG CONNECTION. Leak testing of the appliance shall (3.5 kPa). be conducted by the installer according to the This appliance, as
Summary of the content on the page No. 7
Electrical Wiring Information This appliance is equipped with a grounded type power can be located as is convenient in this left wall or in the cord. A grounded outlet must be provided. It is corresponding right wall. recommended, for convenience, the outlet be located In planning any installation, note that the free length of (with reference to figure 6) as in A or B, below: this appliance’s power cord, extending beyond a point A. If no other appliance is to be installed below this 3-3/4 (9.53
Summary of the content on the page No. 8
Converting Appliance For Use With LP Gas INSTALLATION OF LP ORIFICE SPUDS & CHOKES Propane conversion is to be performed by a JENN-AIR AUTHORIZED SERVICER (or other qualified agency) in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage. The qualified agency performing this work assumes responsibility for this conversion. Electricalpowerandgasmustbetu
Summary of the content on the page No. 9
Step 6: Place 9.2k burner choke(s) into right rear and CONVERSION OF APPLIANCE PRESSURE left front orifice holder with chamfer facing down. (See REGULATOR figure 10). FIGURE12 C.LOW FLAME ADJUSTMENT (See figure 13) This appliance is shipped from the factory with low and high flame settings adjusted for use with natural gas. To set for use with LP proceed as follows: 1. Remove control knob from valve stem. CAUTION: NEVER USE A METAL BLADE TO FIGURE10 PRY KNOB OFF. IF KNOB CANNOT BE EASILY REMOVED
Summary of the content on the page No. 10
After the above operation, the burner will produce a 4. For Step 5: Locate the brass natural gas orifice spuds that were originally installed in this appliance stable, steady blue flame of minimum size. The setting before its conversion for use with LP gas. Observe should be checked by turning knob from high to low the number on each of the spuds and note the several times without extinguishing the flame. correct burner location for each spud as shown in The above operation will automatically pr
Summary of the content on the page No. 11
5. Complete Steps 5, 8 and 9 on pages 8 & 9 to Burner Ignition And complete the installation of natural gas main spuds in their correct locations. Auto-Reignition 6. Save the orifices & chokes removed from the This appliance is equipped for electronic auto-reignition by appliance for future use. They will be needed if this means of a spark igniter located at the rear of each appliance is again converted for use with LP gas. burner. The burners are designed to light at any valve rotation that adm
Summary of the content on the page No. 12
SUPERFICIES PARA COCINAR MANUAL DE DE GAS SELLADAS INSTALACIÓN 403 WEST FOURTH STREET, NORTH NEWTON, IA 50208 Modelos: JGC9430 y JGC9536 IMPORTANTE: Las dimensiones se muestran en pulgadas y centímetros. IMPORTANTE: Asegúrese de que el electrodoméstico esté equipado para el tipo de gas que se suministrará. Consulte la placa de datos que se encuentra en el lado de abajo de la caja de los quemadores para obtener esta información. No trate de convertir este electrodoméstico para usarlo con otro t
Summary of the content on the page No. 13
Ubicación del electrodoméstico Sugerencias importantes para la Jenn-Air preparación Coloque este electrodoméstico alejado de materiales 1. Achaflane todos los bordes expuestos del laminado decorativo para evitar que se dañe con astilladuras. combustibles como cortinas de ventanas y decoraciones combustibles de la pared. 2. Redondeelasesquinasdel hueco ylíjelaspara garantizarquelosbordesestén lisosyevitarque El espacio horizontal libre mínimo entre el borde del sequiebren lasesquinas. Serecomiend
Summary of the content on the page No. 14
Lea la placa de datos de la superficie para cocinar para Toda la tubería de suministro, excepto según se ver si está aprobada la instalación en casas móviles o en especifique, deberá usar tubería de rosca estándar vehículos recreativos. La placa de datos se encuentra en (National Pipe Thread, NPT). En todas las conexiones de la parte inferior de la unidad. la tubería use un compuesto de uniones aprobado que sea resistente a la acción del gas LP. Si está aprobada, se aplicarán los puntos siguient
Summary of the content on the page No. 15
Conexión del electrodoméstico al suministro de gas LA CONEXIÓN DEL SUMINISTRO DE GAS DEBE REALIZARLA UN TÉCNICO CALIFICADO O UN IMPORTANTE INSTALADOR DE ELECTRODOMÉSTICOS DE GAS. Aplique un fluido de detección de fugas anticorrosivo en Las revisiones de fugas del electrodoméstico debe todas las uniones y los accesorios en la conexión de gas realizarlas un instalador de acuerdo con las entre la válvula de cierre de la tubería de suministro y la instrucciones proporcionadas. superficie para cocina
Summary of the content on the page No. 16
2. SI SE VAAINSTALARENESTAUNIDADUN ILUSTRACIÓNDELATUBERÍADELSUMINISTRO HORNO DE PAREDELÉCTRICO, MODELO JJW8530, DEGAS JJW9530, W30400P o JJW8130DE JENN-AIR (HORNO DE PARED INSTALADO DEBAJO DE UNA SUPERFICIE DEBAJO DE LASUPERFICIE PARACOCINAR. PARA COCINAR DE 30” [76 CM]) NOTA1: Este electrodoméstico y las fuentes de suministro eléctrico y de gas deberán instalarse antes de instalar el CAJADELQUEMADOR (PARTE POSTERIOR DEL horno de pared. Vea la ilustración (Información de ELECTRODOMÉSTICO) cablea
Summary of the content on the page No. 17
Métodos alternativos de tubería Pruebas de presión El electrodoméstico debe estar aislado del sistema de para conectar el electrodoméstico tubería de suministro de gas cerrando la válvula de cierre al suministro de gas manual individual durante las pruebas de presión del sistema de tuberías de suministro de gas a presiones de LA CONEXIÓN DEL SUMINISTRO DE GAS DEBE prueba iguales o menores a 1/2 PSIG (3.5 kPa). REALIZARLA UN TÉCNICO CAPACITADO O UN Este electrodoméstico, así como su válvula indiv
Summary of the content on the page No. 18
Información de cableado eléctrico Este electrodoméstico está equipado con un cordón mostrado en la figura 4) puede ubicarse según sea eléctrico con conexión a tierra. Debe proporcionarse un conveniente en la pared izquierda o en la pared derecha tomacorriente conectado a tierra. Se recomienda, para su correspondiente. comodidad, que el tomacorriente esté ubicado (con Si planea una instalación, observe que la longitud libre de referencia a la figura 6) como la A o la B, más adelante: este cordón
Summary of the content on the page No. 19
Conversión del electrodoméstico para usarse con gas LP INSTALACIÓN DE LOS PUNTALES DE ADVERTENCIA ORIFICIO OBTURADORES La conversión al gas propano debe realizarla un TÉCNICO AUTORIZADO DE SERVICIO DE JENN-AIR (u otra agencia calificada) de acuerdo con las instrucciones del fabricante y todos los códigos y requisitos de las autoridades que tengan jurisdicción. No seguir las instrucciones podría causar lesiones graves o daños materiales. La agencia calificada que realice el trabajo asumirá la res
Summary of the content on the page No. 20
Paso 6:Coloque un obturador de quemador de 9.2k en CONVERSIÓN DEL REGULADOR DE los portadores de orificio derecho posterior e izquierdo PRESIÓN DEL ELECTRODOMÉSTICO delantero con el chaflán orientado hacia abajo. (Vea la APLIQUE PRESIÓN figura 10.) HACIA ABAJO CONEL DEDO EN LOS BORDES TAPA DEL QUEMADOR DEL DISCO PARA VOLVERA COLOCAREL PASADORENLA TAPA. APLIQUE PRESIÓNHACIA TAPA Y LOS LADOS CON PASADORDEL EL DEDO PARA CONVERTIDOR TORNILLOS QUITAREL PASADORDE LA TAPA BASE DEL OBTURADOR DE QUEMADOR
