Summary of the content on the page No. 1
Installation 30″ Electric Cooktop
JP340, JP355, JP910, JP930, JP940, JP950
Instructions
“If you have questions, call 800.GE.CARES or visit our website at:
www.GEAppliances.com”
BEFORE YOU BEGIN MATERIALS YOU WILL NEED
Read these instructions completely
and carefully.
•
IMPORTANT — Save these
instructions for local inspector’s use.
Wire Nuts
Junction Box
•
IMPORTANT — Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
TOOLS YOU WILL NEED
instructions with th
Summary of the content on the page No. 2
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS FOR YOUR SAFETY ELECTRICAL REQUIREMENTS • For Personal Safety, remove house fuse This appliance must be supplied with the or open circuit breaker before beginning proper voltage and frequency, and connected installation. Failure to do so could result to an individual, properly grounded branch in serious injury or death. circuit, protected by a circuit breaker or a time delay fuse as noted on rating plate. • Be sure your cooktop is installe
Summary of the content on the page No. 3
ON HOT Installation Instructions PRE-INSTALLATION CHECKLIST 3 Remove Installation Instructions from WARNING – The electrical power literature pack and read them carefully to the cooktop supply line must be shut off before you begin. while connections are being made. Failure to do so could result in serious injury or death. Be sure to place all literature, Owner’s Manual, Installations, etc. in a safe place 1 When preparing cooktop opening, make for future reference. sure the inside of the cabin
Summary of the content on the page No. 4
Installation Instructions PREPARING THE OPENING 1 The following MINIMUM clearance 4 CUTOUT DIMENSIONS dimensions must be maintained. OF THE COUNTERTOP 13″ MAX. Depth of uprotected 1-1/2″ MIN. To insure accuracy, it is best to make a overhead cabinets Clearance from template when cutting the opening in cutout to side wall on the right the counter. of the unit 19-5/8″ width of cut 30″ MIN. 28-1/2″ Clearance from length of 18″ MIN. Height countertop to 1-3/4″ Min. Between cut from countertop unp
Summary of the content on the page No. 5
Installation Instructions INSTALLING THE COOKTOP 1 INSTALLING THE 3 ATTACH FOAM TAPE JUNCTION BOX Apply the foam tape around the outer edge of the glass. Do not overlap the foam tape. Install an approved junction box where it will be easily reached through the front of the Bottom of Cooktop cabinet where the cooktop will be located. The cooktop conduit is 3 feet long. Foam Tape Cooktop Glass 16″ Min. LOCATE MOUNTING PARTS 4 Install junction box so Remove the hold down brackets and screws that i
Summary of the content on the page No. 6
Installation Instructions INSTALLING THE COOKTOP (CONT.) 6 INSERT COOKTOP 7 ATTACH HOLD DOWN INTO CUTOUT BRACKETS TO CABINET Insert the cooktop centered into the cutout Open the cabinet door and screw the hold opening. Make sure the front edge of the down brackets to the cabinet sides with the countertop is parallel to the cooktop. Make screws provided. final check that all required clearances are met. Burner Box Sides Mounting Screw Cooktop Hold Down Bracket Use suitable fasteners for anchorag
Summary of the content on the page No. 7
Installation Instructions INSTALLATION—ELECTRICAL CONNECTIONS A When making the wire connections, use E Once the connections are made, secure the entire length of conduit provided. wires together using wire nuts. The conduit must not be shortened. Red B With the cooktop in place, open the front of the cabinet door. Strain Relief Clamp C Insert the wires from the conduit through the opening of the junction box. Black Ground Red GROUNDING INSTRUCTIONS: Strain Relief Clamp The bare ground wire in t
Summary of the content on the page No. 8
Installation Instructions CHECKLISTS 1 PRE-TEST CHECKLIST 2 OPERATION CHECKLIST A Remove all protective film, if present, A Remove all items from the top and any stickers. of the cooktop surface. B Check to be sure that all wiring is secure B Turn on the power to the cooktop. and not pinched or in contact with (Refer to your Owner’s Manual.) Verify moving parts. that all surface burners operate properly. C Check level of appliance. C Check that the circuit breaker is not tripped nor the house f
