Summary of the content on the page No. 1
Installation instructions
and User guide
Freestanding cooker
OR60 models
NZ AU
Summary of the content on the page No. 2
Summary of the content on the page No. 3
1 Contents Safety and warnings 2 Installation instructions - GAS COOKTOP MODELS 6 Installation instructions - CERAMIC GLASS COOKTOP MODELS 15 FOUR-FUNCTION MODELS WITH GAS COOKTOP Using your oven for the first time 20 Using your oven 21 Cooking functions 22 Using your gas cooktop 23 Cooktop troubleshooting 27 Care and cleaning 28 SEVEN-FUNCTION MODELS WITH GAS COOKTOP Using your oven for the first time 34 Clock and timer 35 Using your oven 36 Cooking functions 37 Au
Summary of the content on the page No. 4
2 Safety and warnings Installation WARNING! Electrical Shock Hazard Always disconnect the cooker from the mains electricity supply before carrying out any maintenance operations or repairs. Models with ceramic glass cooktop: If the ceramic glass cooktop surface becomes cracked, switch the appliance off at the mains power supply and call an Authorised Service Agent. Failure to do so may result in death or electrical shock. WARNING! Cut Hazard Take care - panel edges are sharp. Failure to us
Summary of the content on the page No. 5
3 Safety and warnings Electrical This cooker is to be installed and connected to the electricity supply only by an authorised person. If the installation requires alterations to the domestic electrical system, call a qualified electrician. The electrician should also check that the electrical system is suitable for the electricity drawn by the cooker. The appliance must be connected to the mains, checking that the voltage corresponds to the value given in the rating plate and that the
Summary of the content on the page No. 6
4 Safety and warnings Operation Your freestanding cooker has been carefully designed to operate safely during normal cooking procedures. Please keep the following guidelines in mind when you are using it: WARNING! Explosion Hazard Do not store flammable materials such as gasoline near the cooktop. Do not store flammable material in the oven or drawer. Do not spray aerosols near the cooktop during use. Failure to follow this advice may result in death or serious injury. WARNING! Elec
Summary of the content on the page No. 7
5 Safety and warnings Important safety instructions Never leave the appliance unattended when in use. Boilover causes smoking and greasy spillovers that may ignite. Isolating switch: make sure this cooker is connected to a circuit which incorporates an isolating switch providing full disconnection from the power supply. Household appliances are not intended to be played with by children. Children, or persons with a disability which limits their ability to use the appliance, should hav
Summary of the content on the page No. 8
6 I Installa nstallation instruc tion instructions tions Dimensions and clearances Installation clearances and protection of combustible surfaces shall comply with the current local regulations eg. AG 601 (AS 5601/NZS 5261) Gas Installations code. Installation shall comply with the dimensions in Fig. 1, bearing in mind the following requirements: Overhead Clearances In no case shall the clearance above the highest part of the cooker be less than 600 mm or, for an overhead exhaust fan, 750 mm.
Summary of the content on the page No. 9
7 Installation instructions Levelling the cooker Important! Using the supplied adjustable feet is MANDATORY. For safety reasons and to ensure adequate ventilation, the cooker chassis MUST NOT sit directly on the floor, a plinth, or other support surface. To fit the adjustable feet: 1 Rest the rear of the cooker on a piece of packaging, exposing the base for fitting the feet. 2 Screw the four feet to the cooker. 3 Stand the cooker and level it by screwing Fig. 2 Fitting the adjustable
Summary of the content on the page No. 10
365 235 600 mm (Cavity width) 8 Installation instructions Fitting the anti-tilt bracket (four-function models) Important! To restrain the appliance and prevent it tipping accidentally, fit a bracket to its rear to fix it securely to the wall. Make sure you also fit the supplied lock pin to the anti-tiit bracket. To fit the anti-tilt bracket: 0 1 After you have located where the cooker + 15 + 15 is to be positioned, mark on the wall the place where the two screws of the anti-tilt bracket h
Summary of the content on the page No. 11
3 = = 75 9 Installation instructions Dotted line showing the position Fitting the anti-tilt bracket of the cooker when installed (seven-function models) Important! To restrain the appliance and prevent it tipping accidentally, fit a bracket to its rear to fix it securely to the wall. Make sure you also fit the supplied lock pin to the anti-tiit bracket. To fit the anti-tilt bracket: 0 1 After you have located where the cooker +15 is to be positioned, mark on the wall the place where the t
Summary of the content on the page No. 12
10 Installation instructions Connecting the cooker to the gas supply The gas connection must be carried out by an authorised person according to the relevant standards. Before connecting the appliance to the gas main, mount the brass conical adaptor onto the gas inlet pipe, upon which the washer has been placed (see Figs. 7-8 following). Conical adaptor and washer are supplied with the appliance (packed with conversion kit for use with Natural gas or LPG). This appliance is suitable f
Summary of the content on the page No. 13
11 Installation instructions It is important that the hose does not come in contact with the metal of the appliance and is secured as per appropriate gas installation codes. A chain 80% of the length of the flexible gas hose must be used to prevent stress being applied to the hose. The chain should be attached securely to the product where shown (see Fig.10), and on the wall. Flexible hose assemblies should be AS/NZS 1869 Class B or Class D certified. The thread connection shall be Rp ½
Summary of the content on the page No. 14
12 Installation instructions Converting to a different gas type This appliance is suitable for use with Natural gas or LPG (check the “gas type” sticker attached to the appliance). To convert from one gas type to another, you need to replace the injectors, and then adjust the minimum burner setting. Replacing the injectors 1 Remove the trivets and burners from the cooktop. 2 Using a spanner, remove the injector (shown in Figs. 11-12 following) and replace it with one according to the gas type
Summary of the content on the page No. 15
13 Installation instructions Adjusting the minimum burner setting Check whether the flame spreads to all burner ports when the burner is lit with the gas valve set to the minimum position. If some ports do not light, increase the minimum gas rate setting. Check whether the burner remains lit even when the gas valve is turned quickly from the maximum to the minimum position. If the burner does not remain lit, increase the minimum gas rate setting. To adjust the minimum gas rate setting: 1
Summary of the content on the page No. 16
14 Installation instructions Wiring diagram - Four-function models Cod. 1131682 Wiring diagram - Seven-function models TM F1 S1 PR TS 1a 1 1 2a 2 A N/7 3a 3 1a L/8 4a 4 5a 5 6a 6 7a 7 8a 8 9a 9 10a 10 11a 11 LF CF TL CIR C PA G V S M LN GAS C FOUR FUNC OOKTOP MODELS TION MODELS T
Summary of the content on the page No. 17
15 Installation instructions Dimensions and clearances The cooker must be installed at least 50 mm away from any side walls higher than the cooktop. The cabinetry surrounding the cooker must be made of heat-resistant material and must be able to withstand temperatures of 65 °C above room temperature. Do not install the cooker near flammable materials (eg curtains). If you stand the cooker on a pedestal, make sure you provide safety measures to keep it in place. Cooker overall dimens
Summary of the content on the page No. 18
16 Installation instructions Levelling the cooker Important! Using the supplied adjustable feet is MANDATORY. For safety reasons and to ensure adequate ventilation, the cooker chassis MUST NOT sit directly on the floor, a plinth, or other support surface. To fit the adjustable feet: 1 Rest the rear of the cooker on a piece of packaging, exposing the base for fitting the feet. 2 Screw the four feet to the cooker. 3 Stand the cooker and level it by screwing or Fig. 16a Fitting the
Summary of the content on the page No. 19
3 = = 75 17 Installation instructions Dotted line showing the position Fitting the anti-tilt bracket of the cooker when installed Important! To restrain the appliance and prevent it tipping accidentally, fit a bracket to its rear to fix it securely to the wall. Make sure you also fit the supplied lock pin to the anti-tiit bracket. To fit the anti-tilt bracket: 1 After you have located where the cooker 0 is to be positioned, mark on the wall the +15 place where the two screws of the anti-t
Summary of the content on the page No. 20
18 Installation instructions Connecting the power supply cable Important! This cooker must be connected to the electricity supply only by an authorised person. To connect the power supply cable to the cooker, it is necessary to: 1 Remove the screws that hold cover “A” behind the cooker (Fig. 19b). 2 Position the U bolts “C” onto five-pole terminal block “B” according to the diagram in Fig. 19a. 3 Feed the power supply cable through the cable clamp “D”. The supply cable must be of a suitabl
