Summary of the content on the page No. 1
Gas cooktops
Installation instructions
CG604 & CG905 models
and User guide
GB IE
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Contents 1 Safety and warnings 2 Installation instructions 6 Introduction 18 Using your cooktop 19 Cooking guidelines and cookware 22 Care and cleaning 24 Troubleshooting 29 Warranty and service 31 Important! SAVE THESE INSTRUCTIONS The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our local website listed on the back
Summary of the content on the page No. 4
2 Safety and warnings Installation WARNING! Electrical Shock Hazard Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. Connection to a good earth wiring system is absolutely essential and mandatory. Alterations to the domestic wiring system must only be made by a qualifi ed electrician. Failure to follow this advice may result in electrical shock or death. WARNING! Cut Hazard Beware of sharp edges when handling s
Summary of the content on the page No. 5
3 Safety and warnings Important safety instructions! Installation This appliance shall be installed in accordance with the applicable regulations in force and only used in a well ventilated space. Read the instructions before installing or using this appliance. Please make this information available to the person installing the appliance as it could reduce your installation costs. This appliance must be installed and serviced only by a suitably qualified and registered person. In orde
Summary of the content on the page No. 6
4 S Sa af fe et ty y and w and warnings arnings Operation WARNING! Hot Surface Hazard This appliance becomes hot during use. Do not touch the cooktop components, burners, trivets, pan supports or the base when hot. Before cleaning, turn the burners off and make sure the whole cooktop is cool. Failure to follow this advice may result in serious injury. WARNING! Fire Hazard Never leave the appliance unattended when in use. Boilover causes smoking and greasy spillovers that may ignite. Never us
Summary of the content on the page No. 7
5 S Sa af fe et ty y and w and warnings arnings Important safety instructions! Operation Keep children away from the cooktop when it is in use. Household appliances are not intended to be played with by children. Children, or persons with a disability which limits their ability to use the appliance, should have a responsible person to instruct them in its use. The instructor should be satisfied that they can use the appliance without danger to themselves or their surroundings. Do not use
Summary of the content on the page No. 8
CG905DWAC CG905DWFC CG604DWFC 6 Installation instructions A B E D C H J G I F Cooktop and cutout dimensions (mm) 578 914 914 A overall width of cooktop overall depth of cooktop 511 533 546 B height of chassis below top of bench 50 50 76 C D width of chassis 554 840 855 480 480 470 E depth of chassis overall width of cutout 560 870 870 F overall depth of cutout 490 494 494 G H corner radius of cutout max. 10 max. 10 max. 10 distance from right edge of cutout to 30 30 30 I manifold centre line di
Summary of the content on the page No. 9
CG905DWAC CG905DWFC CG604DWFC 7 Installation instructions B C A D E Clearances (mm) minimum clearance from left or right edge of cutout to: A nearest vertical surface* 140 140 100 minimum clearance from rear edge of cutout to: B nearest vertical surface 110 110 115 minimum clearance from pan supports to: rangehood 650 650 650 any other overhead exhaust fan C 800 800 800 downward-facing combustible surface (overhead cabinetry) 650 650 650 downward-facing tiled or fi re-
Summary of the content on the page No. 10
8 Installation instructions Before you start Before starting to install the cooktop, make sure that: the cooktop has not been damaged during transport. In case of doubt after unpacking and checking it, contact the retailer the local distribution conditions (nature of gas and pressure) and the adjustment of the cooktop (as detailed on the appliance data label and in section ‘Gas supply and gas rate summary’ further below) are compatible the installation will comply with the relevant vent
Summary of the content on the page No. 11
9 Installation instructions Electrical connection requirements This appliance must be connected to a 220-240 V 50 Hz power supply only and earthed via the power supply cable. In the United Kingdom, the suitably earthed three-pin plug must be protected by a 3 A fuse. A suitable isolating switch providing full disconnection from the mains power supply must be incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The is
Summary of the content on the page No. 12
10 Installation instructions Fastening the cooktop to the bench This cooktop is suppled with fastening brackets (and screws) that will cope with a bench thickness of 20-50 mm. For benches thicker than 50 mm, recess the underside to a thickness of 20-50 mm. 50 mm recessed to 20 mm 50 mm Fig.1 Fastening the cooktop to the bench Connecting the cooktop to the gas supply Important! This cooktop is supplied factory-set for Natural gas, but is suitable for installation with either Natural gas
Summary of the content on the page No. 13
11 Installation instructions Special requirements for CG604DWFC and CG905DWFC models Gas connection to these cooktops MUST use the elbow supplied. Where a regulator is required to satisfy local market regulations, it must be connected to the elbow to prevent gas leakage. In some countries, the supplied elbow has a 1/2” taper male thread (Fig. 2a). In other countries, the supplied elbow has a 1/2” parallel male thread and a conical adaptor (1/2” taper male thread) may be supplied
Summary of the content on the page No. 14
12 Installation instructions BS 21/ISO 7-1 R 1/2” Fibre washer Elbow Fig.2a Gas connection to the cooktop: elbow with 1/2” taper male thread (CG604DWFC and CG905DWFC models) ISO 228-1 G 1/2” BS 21/ ISO 7-1 R 1/2” Fibre washer Elbow Fibre washer Conical adaptor for elbow (use only if required) Fig.2b Gas connection to the cooktop: elbow with 1/2” parallel male thread and conical adaptor (if required) (CG604 DWFC and CG905DWFC models) Gas inlet (BS 21/ ISO 7-1 Rp 1/2”) Fig.3 Gas connection to
Summary of the content on the page No. 15
13 Installation instructions Leak-testing and flame-testing the cooktop Important! The operation of the cooktop, including the ignition system, must be tested before installation is complete. If, after following the instructions below, satisfactory performance cannot be obtained, contact the local gas authority or your local Authorised Service Centre for advice and assistance. Checking the connections for leaks After installation and making all connections, check thoroughly for possi
Summary of the content on the page No. 16
14 Installation instructions Converting to a different gas type Important! Gas conversion may only be carried out by a suitably qualified and registered person. To convert from one gas type to another, you need to replace the injectors and adjust the minimum burner setting. To replace the injectors, you will need a 7 mm box spanner (and a 10 mm ring spanner for CG905DWAC models). These are not supplied. 1 Disconnect the cooktop from the power supply. Important! Disconnect cooktop from the
Summary of the content on the page No. 17
15 Installation instructions Adjusting the minimum burner setting This has been adjusted at the factory for Natural gas but may need adjusting for local conditions. When converting to LPG, the minimum setting MUST be re-adjusted for each burner. To adjust the minimum setting, you will need a Ø 2.5 x 45 mm screwdriver. 1 Light the burner and set the control dial to its minimum. 2 Remove the dial. 3a For Natural gas (G20, G25, or G20/G25 depending on gas category) Slowly tu
Summary of the content on the page No. 18
16 Installation instructions Gas supply and gas rate summary Gas supply: These products are factory-set for Natural gas (G20, G25, or G20/G25 depending on gas category). For conversion to LPG (G30/G31), see section ‘Converting to a different gas type’. Classification: Class 3 – Appliance for building into a kitchen unit or worktop. Burner AUX I L I AR Y SE M I -R API D W OK R API D Gas type NG LPG NG LPG NG LPG NG LPG CG905DWAC II2H3+ 75 S 1.0 050 1.1 80 97 Z 1.9 058 M 1.7 124 169 5.5 114 5.5
Summary of the content on the page No. 19
17 Installation instructions Final checklist TO BE COMPLETED BY THE INSTALLER Have you securely fastened the cooktop to the bench with the supplied brackets? All models except CG905DWAC: Have you used the supplied elbow (and conical adaptor if required) and fibre washer(s) to connect the gas to the inlet on the cooktop? Have you leak-tested all connections? Are the injector sizes correct for the gas type? Is the shut-off valve on the gas supply accessible to the cus
Summary of the content on the page No. 20
18 Introduction About your new cooktop Thank you for buying a Fisher & Paykel gas cooktop. Once it is installed and ready to use, you will want to know everything about it to make sure you get excellent results right from the start. We recommend you read the whole guide before using your new cooktop, for both safety and cooking success. For more information, visit our local website listed on the back cover. Before using your new cooktop Read this user guide, taking special note of the ‘Safety
