Summary of the content on the page No. 1
Installation Instructions
Warming Drawer
Models: DWD30, ERWD27, ERWD30, EWD24, EWD27,
EWD30, EWD36, IWD24, IWD27, IWD30, MRWD27,
MRWD30, MWDH27, MWDH30, MWDV27,
MWDV30, OWD24, RWDV30
Part No. 102345 Rev. S
Preliminary - For Review Only
Summary of the content on the page No. 2
® All specifications are subject to change without notice. Dacor assumes no liability for changes to specifications. © 2007 Dacor, all rights reserved.
Summary of the content on the page No. 3
Table of Contents Before You Begin... ........................................................... 1 Installation Instructions .................................................... 7 Important Safety Instructions .......................................... 1 Remove the Drawer ........................................................ 7 General Safety Precautions ............................................. 2 Installing the Chassis ....................................................... 7 Installati
Summary of the content on the page No. 4
Important Safety Instructions General Safety Precautions To reduce risk of fire, electric shock, serious injury or death when using your appliance, follow basic precautions, including the following: WARNING WARNING • Clean the warming drawer thoroughly before • Use this appliance only for its intended use as operating it for the first time. described in this manual. Use it only to warm food and heat plates and utensils. It is not designed for • To reduce the risk of fire in the warming
Summary of the content on the page No. 5
Installation Specifications Verifying the Package Contents C B • (3) mounting screws - PN 83569 • Wire rack with mounting hardware (OWD24 only) (1) PN 83619 (screw), (1) PN 83267 (clamp) Installation Planning Chassis E • A qualified technician must complete the installation of this built- in appliance. Proper installation is the customer's responsibility. • Carefully check the location where the drawer is to be installed. 5/16” (8 mm) The drawer should be placed for convenient access. Make
Summary of the content on the page No. 6
Installation Specifications (A) Drawer Face (B) Chassis Face Model (C) Chassis Width Width Width DWD30 30” (76.2 cm) 29 5/8” (75.2 cm) 28 1/4” (71.8 cm) 10 1/8” ERWD27 27” (68.6 cm) 26 5/8” (67.6 cm) 25 1/4” (64.1 cm) (25.7 cm) ERWD30 30” (76.2 cm) 29 5/8” (75.2 cm) 28 1/4” (71.8 cm) EWD24 24” (61.0 cm) 23 5/8” (60.0 cm) 22 1/4” (56.5 cm) EWD27 27” (68.6 cm) 26 5/8” (67.6 cm) 25 1/4” (64.1 cm) EWD30 30” (76.2 cm) 29 5/8” (75.2 cm) 28 1/4” (71.8 cm) EWD36 36” (91.4 cm) 35 5/8” (90.5 cm) 34 1/4”
Summary of the content on the page No. 7
Installation Specifications 27"/30"/36" Dacor single wall oven 3/4" min.* Warming (1.9 cm) D C drawer 36" typ. Warming 120 Vac D C (91.4 cm) drawer 120 Vac elect. Warming C electrical drawer D outlet 3/4" min.* Warming (1.9 cm) 120 Vac C drawer elect. A B 1 1/2" (3.8 cm) Toe kick Cooktop Typical countertop 3/4" min.* A (1.9 cm) 3/4” min.* Cutouts Dimensions (1.9 cm) Warming C drawer NOt ES: • Models EWD36 and OWD24 cannot be installed above or below another 36" typ. 120 Vac electrical (91.4
Summary of the content on the page No. 8
Installation Specifications Install Support Platform in Chassis Cabinet face Provide a platform (100 lb. load capacity) within the cabinet upon which the warming drawer will be supported. The platform must be installed level and straight. The top edge Support of the platform must be flush with the cutout at the front of platform the cabinet. There are no provisions to level the warming drawer after it has been installed. 3/4” (1.9 cm) thick plywood is recommended. NOt E: If the drawer is
Summary of the content on the page No. 9
Installation Instructions WARNING Installing the Chassis • T o avoid personal injury caused by the appliance 1. Grasp the warming drawer chassis on opposite falling forward when the drawer is opened, secure sides and slide it partially into the cabinet opening. the chassis to the cabinet and support platform as Temporarily support the chassis in place so that it will instructed. not tilt or fall. • Be certain that the power plug is disconnected from 2. From an adjoining cabinet, reach
Summary of the content on the page No. 10
Installation Instructions Re-installing the Drawer Towel Rack Installation 1. Pull the drawer slides all the way out of the drawer (OWD24 Only) opening. Model OWD24 is designed so that it can be used as a 2. Gently lower the drawer between the extended slides towel warmer if desired. Other models are not equipped for until it is suspended by them. this application. To use model OWD24 as a towel warmer, 3. Slide the back of the drawer mounting brackets under you must install the towel rack
Summary of the content on the page No. 11
Installation Instructions Warming Drawer Control Panel Layout Verify Warming Drawer Installation Checklist Operation WARNING 1. Connect power plug to the electrical outlet. • To ensure a safe and proper installation, the following 2. Open the drawer and press the ON/OFF key on the checklist should be completed by the installer to control panel. ensure that no part of the installation has been overlooked. 3. Press the PROOF, LOW, MED and HIGH keys each in turn. When you press each key,
Summary of the content on the page No. 12
Dacor ● 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www .dacor .com
