Summary of the content on the page No. 1
Ovens with
FL-2269
Microprocessor Controls
Rev. 10 (6/08)
Page 1 of 13
5925 Heisley Road • Mentor, OH 44060-1833
INSTALLATION, OPERATION and MAINTENANCE MANUAL
for Cres Cor
CONVECTION and RETHERM OVENS
with MICROPROCESSOR CONTROLS
CO151FUA12B-Q1 CO151HUA6B-Q1
CO151FPUA12B-Q1 CO151H189B-Q1
CO151F1818B-Q1 CO151XUA5B-Q1
RO151FUA18B-Q1 CO151X185B-Q1
RO151F1332B-Q1
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Summary of the content on the page No. 2
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 2 of 13 5925 Heisley Road • Mentor, OH 44060-1833 TABLE OF CONTENTS SUBJECT PAGE INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3, 4 OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4, 5, 6 Illustration, Figure 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 3 of 13 5925 Heisley Road • Mentor, OH 44060-1833 INSTALLATION INSTRUCTIONS VENTING YOUR OVEN: 3. Most jurisdictions consider our low-temperature ovens 1. The purpose of ventilating hoods is to direct and capture (maximum temperature is 350°F/177°C) as low-heat smoke, grease-laden vapors, heat, odors, or fumes. appliances not requiring vent hoods. 2. Low temperature equipment (maximum temperature 4. Installation must conform wit
Summary of the content on the page No. 4
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 4 of 13 5925 Heisley Road • Mentor, OH 44060-1833 INSTALLATION INSTRUCTIONS (continued) Note: Cold food is NOT to be added when unit is operating HOW TO INSTALL CABINETS: 1. Remove all packing material from inside and outside of in HOLD mode. For HOLD mode, preheat unit to cabinet. 180°F/82°C for 60 minutes. 2. Position cabinet on level fl oor; install the cabinet interior (pan slides) if not already installed. CAUTION 3. Plug pow
Summary of the content on the page No. 5
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 5 of 13 5925 Heisley Road • Mentor, OH 44060-1833 OPERATING INSTRUCTIONS (continued) 7. The oven will beep and automatically switch to the HOW TO SET THE CONTROL, continued HOLD mode at the end of the cooking cycle. The Cook FOR PROBE COOK OPERATION: lamp will go out and the Hold lamp will light up. Press the SELECT button to choose the probe mode. Probe Cooking PROBE TEMPERATURE: See “HOW TO SET THE CONTROL” (on page 5) for
Summary of the content on the page No. 6
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 6 of 13 5925 Heisley Road • Mentor, OH 44060-1833 OPERATING INSTRUCTIONS (continued) WARNING Cleaning Hints: BEFORE cleaning the cabinet: 1. Use the mildest cleaning procedure that will do the job. 1. Unplug cord from wall. Allow cabinet to cool. 2. Always rub in the direction of the polish lines to avoid scratching the surface. 2. Do NOT hose cabinet with water. 3. Use only a soft cloth, sponge, fi brous brushes, plastic or sta
Summary of the content on the page No. 7
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 7 of 13 5925 Heisley Road • Mentor, OH 44060-1833 MAINTENANCE INSTRUCTIONS TROUBLE-SHOOTING GUIDE (continued) PROBLEM POSSIBLE CAUSE SOLUTION 1. Fuse 1. Replace 2. Control 2. Replace Cabinet does not heat, or doesn’t heat 3. Sensor 3. Replace properly 4. Heater contactor 4. Replace 5. Loose wiring at heater contactor 5. Replace 6. On/Off Switch 6. Replace 1. On/Off Switch 1. Replace 2. Fuse 2. Replace Blowers do not operate 3. Blowe
Summary of the content on the page No. 8
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 8 of 13 5925 Heisley Road • Mentor, OH 44060-1833 REPLACEMENT PARTS Include all information on nameplate when ordering parts 2 1 TM Roast-N-Hold + MODE TIME / TEMPERATURE SETPOINTS ( I ) ON COOK PROBE TIMED PROBE SELECT SET HEAT COOK HOLD TIME OVEN START STOP HOLD TEMP OFF ( 0 ) POWER FIGURE 2: CONTROL PANEL Hot Unit Replacement Parts ITEM DESCRIPTION Part No. ITEM DESCRIPTION Part No. PARTS for 8200W, 1-PH UNITS 1. Switch (On/Off) 0
Summary of the content on the page No. 9
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 9 of 13 5925 Heisley Road • Mentor, OH 44060-1833 REPLACEMENT PARTS (continued) FULL SIZE CABINET REPLACEMENT PARTS: MODEL PREFIX CO-151, RO-151 (“Q” Series) DESCRIPTION -F1332 -FUA (12), (18) -FPUA (12), (18) -F1818 Hot Unit, 208V, 1PH HU675058Q1 HU675017Q1 HU675062Q1 HU675021Q1 Hot Unit, 208V, 3PH HU675060Q1 HU675018Q1 HU675064Q1 HU675022Q1 Hot Unit, 240V, 1PH HU675059Q1 HU675019Q1 HU675063Q1 HU675023Q1 Hot Unit, 240V, 3PH HU675061
Summary of the content on the page No. 10
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 10 of 13 5925 Heisley Road • Mentor, OH 44060-1833 REPLACEMENT PARTS for OVENS CO or RO151F SERIES Include all information on nameplate when ordering parts 6 11 10 8 9 5 4 23 21 7 3 FIGURE 3; 22 Hot Unit w/o Top cover 14 13 12 22 (For parts description, refer to page 8.) FIGURE 4; Bottom of Hot Unit, Cover Removed (For parts description, refer to page 8.) Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Summary of the content on the page No. 11
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 11 of 13 5925 Heisley Road • Mentor, OH 44060-1833 REPLACEMENT PARTS for “PASS-THRU” OVENS CO or RO151FPUA SERIES Include all information on nameplate when ordering parts 23 21 8 7 3 4 5 6 FIGURE 3; Hot Unit w/o Top cover 11 10 9 (For parts description, refer to page 8.) 12 13 14 22 FIGURE 4; Bottom of Hot Unit, Cover Re- moved (For parts description, refer to page 8.) Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www
Summary of the content on the page No. 12
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 12 of 13 5925 Heisley Road • Mentor, OH 44060-1833 WIRING DIAGRAM 30 29 1 PHASE V HIGH TEMP V 26 28 G L2 L1 L1 FUSE 1 3 FUSE 2 4 14 HEATER 18 CONTACTOR 1 H1 HIGH LIMIT 7 9 6 12 17 16 2 H2 8 8 10 11 HIGH LIMIT H3 6 13 A 18 19 20 POWER 14 27 SWITCH BM BM BM 5 L R C 22 21 AC-N 110v 220v SENSOR OVEN 24 FAN RTD1 t° Temp. Control 23 Board SENSOR 15 PROBE HEAT RTD2 t° 5 25 SINGLE PHASE 3 PHASE 30 29 V HIGH TEMP V 26 28 G L3 L2 L1 L1 F
Summary of the content on the page No. 13
Ovens with FL-2269 Microprocessor Controls Rev. 10 (6/08) Page 13 of 13 5925 Heisley Road • Mentor, OH 44060-1833 OPERATING INSTRUCTIONS FOR OVENS WITH OPTIONAL PRODUCT KEYS PROBE RECEPTACLE POWER SWITCH PRODUCT KEYS CONTROL MODE SETPOINTS ON TIME - TEMPERATURE RETHERM COOK PROBE TIMED TIME SET SELECT HEAT COOK HOLD PROBE OVEN START STOP HOLD TEMP OFF POWER CONTROL PANEL The Product Keys provide automatic menu selections Product Key Programming (arranged in banks of 5 keys, max. 10 keys). Each
