Summary of the content on the page No. 1
Touchmonitor User Guide
For 12” LCD Desktop
1229L
Summary of the content on the page No. 2
Elo Touchmonitor User Guide 12.1" LCD Touchmonitor with Optional Mag Stripe Reader, Finger Print Reader and Rear Facing Customer Display ET1229L Series Revision B P/N 008577 Elo TouchSystems, Inc. 1-800-ELOTOUCH www.elotouch.com
Summary of the content on the page No. 3
Copyright © 2008 Tyco Electronics. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise with- out prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo T
Summary of the content on the page No. 4
Table of Contents Chapter 1 Chapter 3 Introduction 1 Operation 31 Product Description ...................................................1 About Touchmonitor Adjustments ..............................31 Detailed LCD Display Performance Controls and Adjustment ............................................33 Requirements .............................................................2 OSD Lock/Unlock ......................................................33 Customer Display ...........................
Summary of the content on the page No. 5
Appendix C Technical Specifications 43 Table of Contents Display Modes ..........................................................43 Touchmonitor Specifications ...................................... 44 AccuTouch Touchscreen Specifications .............45 IntelliTouch Touchscreen Specifications ..............46 Infrared Touchscreen Specifications ...................47 12.1" LCD Touchmonitor (ET1229L-XXWA-1-G) Dimensions ..........................................................48 Regulatory Infor
Summary of the content on the page No. 6
C H A P T E R 1 INTRODUCTION Product Description The 1229L is a retail terminal designed to present information to the operator and the customer. The 1229L is available in serial and USB versions. The 1229L functionally consists of a 12.1” LCD main display with a touchscreen, an optional vacuum fluorescent display (VFD) Customer Display, an optional fingerprint reader (USB version only), an optional credit card reader, and a 6 port USB (USB version only) Hub. The main display element is a 12.1 i
Summary of the content on the page No. 7
The credit card reader reads all three stripes on a standard credit card or drivers license. The credit card is read by sliding the credit card, stripe side toward the display through the credit card reader forward or backward. There is a serial credit card reader and a USB credit card reader. The Hub provides 4 internal USB ports to be used by the credit card reader, the fingerprint reader, the touchscreen, and the customer display. The hub also supplies two USB ports to the outside of the back
Summary of the content on the page No. 8
Video Interface Connector The video interface connector is a High density 15 pin type HD-15. Indicator Lamps The LCD display shall provide an indicator lamps to give the status of the Power Management System Audio Jack Provides for audio input signal to the stereo speakers mounted in the 1229L. Customer Display The Customer Display is a twenty character two line vacuum fluorescent display (VFD). It consists of a VFD and VFD controller. There is a serial version controller and a USB controller. T
Summary of the content on the page No. 9
Specifications Sensor SecuGen FOR Image Capture Speed 600ms / frame Image Transfer Speed 500Byte / ms Pixel Resolution 356 x 292 USB Signaling Type Full Speed Type Theory of Operation The USB host initiates communication with the FDU01 using operation commands (Sensor LED On, Fingerprint Capture Start and Stop). Fingerprint data are then captured by the CMOS sensor at a total image size of 356 x 292 with 8-bit gray level. The image frame transfer speed is 500 bytes/ms. It takes about 600 millise
Summary of the content on the page No. 10
Six Port USB Hub The Hub provides 4 internal USB ports to be used by the credit card reader, the fingerprint reader, the touchscreen, and the customer display. The hub also supplies two USB ports to the outside of the back of the 1229L for external use. The hub is only used by the USB version of the 1229L. The hub meets the following requirements: Specification Full compliance with USB specification 1.0, 1.1 and HID Class Definition Rev 1.0. Hub shall be self powered Hub shall provide 2 external
Summary of the content on the page No. 11
1-6 Elo Touchmonitor User Guide
Summary of the content on the page No. 12
C H A P T E R 2 INSTALLATION AND SETUP This chapter discusses how to install your LCD touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor Check that the following items are present and in good condition: Brick power supply VGA cable Touchmonitor OR Serial cable USB cable (one for each option) CD and Quick Install Power cable US/Canada European power cable Guide 2-7
Summary of the content on the page No. 13
Product Overview Main Unit Rear View 2-8 Elo Touchmonitor User Guide
Summary of the content on the page No. 14
Side View Base Bottom View 2-9
Summary of the content on the page No. 15
Kensington™ Lock The Kensington™ lock is a security device that prevents theft. To find out more about this security device, go to http://www.kensington.com. 2-10 Elo Touchmonitor User Guide
Summary of the content on the page No. 16
Serial Interface Connection Your touchmonitor comes with one of the following touchscreen connector cables: Serial (RS- 232) cable or USB cable. (For Windows 98, 2000, Me and XP systems only.) To set up the display, please refer to the following figures and procedures: Remove the Back Cover The cables are connected at the back of the monitor. • To remove the cover, grasp the lip of the cover and pull towards you until it snaps off. 2-11
Summary of the content on the page No. 17
CAUTION Before connecting the cables to your touchmonitor and PC, be sure that the computer and touchmonitor are turned off. NOTE: Before connecting the cables to the touchmonitor, route all the cables through the hole in the stand as shown in the picture above. 2-12 Elo Touchmonitor User Guide
Summary of the content on the page No. 18
Serial Connection Option The following illustrations guide you step by step in connecting your touchmonitor using a serial cable connection. • Connect one end of the video cable to the rear side of computer and the other to the LCD monitor. Tighten by turning the two thumb screws clockwise to ensure proper grounding. 2-13
Summary of the content on the page No. 19
• Connect one end of the brick power supply to the monitor and the other end to the connector of the power cable. • Connect the power cable to the power port in the monitor. • After connecting the power cable, secure the cable under the cable 2-14 Elo Touchmonitor User Guide
Summary of the content on the page No. 20
• Connect one end of the speaker cable to the speaker port in the computer and the other end to the port in the monitor • After connecting the speaker cable, secure it under the cable management clip. 2-15
