Summary of the content on the page No. 1
HM703UT
HF703UT
USER MANUAL
ENGLISH
TABLE OF CONTENTS
DEUTSCH
FOR YOUR SAFETY............................................................ 1
SAFETY PRECAUTIONS............................................ 1
FRANCAIS
CUSTOMER SERVICE................................................ 3
CLEANING................................................................... 3
NEDERLANDS
BEFORE YOU OPERATE THE MONITOR.......................... 4
FEATURES...............................................................
Summary of the content on the page No. 2
Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services t
Summary of the content on the page No. 3
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chlorid
Summary of the content on the page No. 4
FCC DECLARATION OF CONFORMITY Model Number: HM703UT / HF703UT Trade Name: iiyama Responsible party: Iiyama North America, Inc. Address: 1560 Brookhollow Drive, Suite 208, Santa Ana, CA 92705 U.S.A. Telephone number: 714-437-5111 This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This equipment may not cause harmful interference, and (2) this equipment must accept any interference received, including interference that may cause undesir
Summary of the content on the page No. 5
FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. NEVER REMOVE THE CABINET High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock. DO NOT PUT ANY OBJECT INTO THE MO
Summary of the content on the page No. 6
CAUTION MAINTAIN GOOD VENTILATION Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls. Do not remove the stand when operating the monitor. Ventilation slots on the cabinet bottom will be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage. Operating the monitor on its back, side, upside down or on a carpet or
Summary of the content on the page No. 7
OTHERS Only available on HM703UT ATTENTION FOR USING THE OPQ FUNCTION (=Optimize Picture Quality) 2 Due to the nature of the Diamondtron M -CRT, misconvergence, misalignment of the aperture grille, picture shaking or burn-in of phosphors may happen when displaying a high-white picture for a long time while the OPQ function is active. Turn OFF the OPQ function when displaying anything other than DVD or other moving pictures. OPTIMUM PICTURE FOR THE OPQ FUNCTION [On screen display] OPQ Function 1.
Summary of the content on the page No. 8
BEFORE YOU OPERATE THE MONITOR FEATURES HM703UT: High Brightness ® Crisp, Clear Display for Windows or Macintosh Supports Resolutions up to 1600×1200 Supports Refresh Rate up to 89Hz at 1280×1024 ® Windows 95/98/Me/2000 Plug & Play Compliant sRGB International Standard Compliant ® Power Management (ENERGY STAR and VESA DPMS Compliant) Space Saving, Compact Case Design Ergonomic Design: TCO ’99 and MPR 2 Approved ACCESSORIES The following accessories should be included in the V
Summary of the content on the page No. 9
INSTALLATION OF TILT AND SWIVEL STAND The monitor is designed to be used with the stand installed. Be sure to install the stand before operating the monitor. CAUTION Install the stand on a stable surface. The monitor may cause injury or damage if it falls or is dropped. Do not give a strong impact to the monitor. It may cause damage. Unplug the monitor before installation to avoid electric shock or damage. A Ensure that the monitor is switched off. Carefully turn the monitor on its side or
Summary of the content on the page No. 10
LOCATION OF CONTROLS Power Indicator A Power Switch B + Button C – Button D Menu Button E Input Select Button (VIDEO 1/2) F Select either VIDEO IN 1 or 2 for the signal input when both of the signal inputs are connected to a signal source. Switch VIDEO IN 1 and 2 whenever pressing Input Select Button for 1-2 seconds. D-Sub mini 15pin Connector (VIDEO IN 1) G D-Sub mini 15pin Connector (VIDEO IN 2) H AC Connector (AC IN) I 6 BEFORE YOU OPERATE THE MONITOR ENGLISH
Summary of the content on the page No. 11
CONNECTING YOUR MONITOR Ensure that both the computer and the monitor are switched off. A Connect the computer to the monitor with the signal cable. (See page 19 for CONNECTOR PIN B ASSIGNMENT.) Connect the Power Cable to the monitor first and then to the power supply. C NOTE The signal cables used for the connection vary by the type of computers you use. An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard
Summary of the content on the page No. 12
OPERATING THE MONITOR The iiyama Vision Master has been preset at the factory with the signal timings listed on page 19 in PRESET MODES to create the best picture. If an incorrect picture appears during the operation, adjust the image by following the procedure below to get the desired picture. After selecting an item in the Main Menu, the adjustments and settings are made in the Sub-Menu. Main Menu appears on the screen when you press the Menu Button. ( For example, to adjust the horizontal scr
Summary of the content on the page No. 13
ADJUSTMENT MENU CONTENTS Main Menu Sub-Menu Problem / Option Button to Press Too dull Contrast Direct Too intense Color Too dark Brightness Control Direct Too bright 1 Color 1: 9300K COLOR Color Temp. 2 Color 2: 6500K 3 Color 3: 5000K S sRGB User color: Red / Blue NOTE sRGB is an international standard which defines and unifies the difference of color appearance between equipment. You can not adjust the Contrast, Brightness and OPQ during sRGB mode because those settings are loc
Summary of the content on the page No. 14
Main Menu Sub-Menu Problem / Option Button to Press Too small Zoom Too large Screen Too small Control H-Size Too large Too far to the left H-Position Too far to the right Too small V-Size Too large Too low V-Position Too high Return to Menu Return to Main Menu. Pin-Cushion To correct distortion Shape Trapezoid To correct distortion Parallelogram To correct distortion Pin-Balance To correct distortion Tilt To correct tilt Return to Menu Return to Main Menu. 10 OPERATING THE MONI
Summary of the content on the page No. 15
Main Menu Sub-Menu Problem / Option Button to Press To correct vertical H-Moire wavy lines To correct horizontal Picture 1 V-Moire* Quality wavy lines NOTE Moiré is the result of interference between the phosphor layout and the video signal. By changing the horizontal and vertical size, the moiré can be reduced. You may find the moiré more noticeable depending on the Desktop Pattern you select. In this case, change the desktop pattern. If moiré is still noticeable, use this function
Summary of the content on the page No. 16
Main Menu Sub-Menu Problem / Option Button to Press To move the OSD to the left / OSD H-Position center / right Function To move the OSD to the top / OSD V-Position center / bottom 3 5 15 30 45 sec OSD Off Timer You can set the OSD display time to any one of the above 5 settings. English English Language Deutsch German Francais French Nederlands Dutch Svenska Swedish Japanese Japanese All adjustment items except this function On are locked out. Lockout Off Lockout is cancele
Summary of the content on the page No. 17
POWER MANAGEMENT FEATURE The power management feature of this product complies with every power saving requirement of ® ENERGY STAR and VESA DPMS. When activated, it automatically reduces unnecessary power consumption of the monitor when your computer is not in use. To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a power management step the monitor takes as described below. The power management function, including any timer settings is configured
Summary of the content on the page No. 18
SELF-DIAGNOSIS FUNCTION The monitor has a self-diagnosis function. The monitor diagnoses itself automatically when the picture does not appear and the power indicator is green or orange because of the failure of computer or monitor. Procedure A Disconnect the signal cable of the computer or turn OFF the computer. B Turn ON the monitor. Diagnosis A A full white picture is displayed: The monitor is working normally. Check the computer. B A full white picture is not displayed: The monitor may b
Summary of the content on the page No. 19
TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. 1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. 2. Consult the following charts if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. 3. If you are experiencing a problem which is not described below or you cannot correct the problem, discontinue using the monitor and contact your deal
Summary of the content on the page No. 20
2 Normal phenomenon on ‘Diamondtron M -CRT’ monitors HM703UT Misalignment of Aperture Grille 2 Due to the nature of the Diamondtron M -CRT, in rare cases, a misalignment of the aperture grille may happen by the shock or vibration caused during transportation. If a black vertical line appears on the screen, apply a light shock to the side of the monitor with your hand. If the problem persists, follow the procedure below. Display a full white picture and inspect the problem area. A Display a high-
