Summary of the content on the page No. 1
Q9
LCD Display
Model No. : VS11455
Summary of the content on the page No. 2
Contents TCO Information.......................................................................................... i Compliance Information.............................................................................. 1 Important Safety Instructions...................................................................... 2 Declaration of RoHS Compliance............................................................... 3 Copyright Information ............................................................
Summary of the content on the page No. 3
TCO Information Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of goo
Summary of the content on the page No. 4
Below you will find a brief summary of the ecological requirements met by this product. The complete ecological criteria document can be found at TCO Development’s website http://www.tcodevelopment.com or may be ordered from: TCO Development SE-114 94 STOCKHOLM, Sweden Fax: +46 8 782 92 07 E-mail: development@tco.se Information regarding TCO’99 approved and labelled products may also be obtained at http://www.tcodevelopment.com Ecological requirements Flame retardants Flame retardants may be
Summary of the content on the page No. 5
Compliance Information For U.S.A. This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec
Summary of the content on the page No. 6
Important Safety Instructions 1. Read these instructions completely before using the equipment. 2. Keep these instructions in a safe place. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this equipment near water. Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 6. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the Display” in this guide for further instructions. 7. Do not block any ventilati
Summary of the content on the page No. 7
Declaration of RoHS Compliance This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.1% M
Summary of the content on the page No. 8
Copyright Information ® Copyright © ViewSonic Corporation, 2007. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards As
Summary of the content on the page No. 9
Getting Started ® Congratulations on your purchase of a ViewSonic LCD display. Important! Save the original box and all packing material for future shipping needs. NOTE: The word “Windows” in this user guide refers to the following Microsoft operating systems: Windows ‘95, Windows NT, Windows ‘98, Windows 2000, Windows Me (Millennium), and Windows XP. Package Contents Your LCD display package includes: •LCD display • Power cord • Wizard CD-ROM • Quick Start Guide NOTE: The CD includes the User G
Summary of the content on the page No. 10
Quick Installation 1. Connect power cord (and AC/DC • Wait for the CD-ROM to auto-start. adapter if required) NOTE: If the CD-ROM does not auto- start: double-click on the CD-ROM icon in 2. Connect video cable the Windows Explorer, then double-click • Make sure both the LCD display and on viewsonic.exe. computer are turned OFF • Follow the on-screen instructions. • Remove rear panel covers if necessary 5. Windows users: Set the timing mode • Connect the video cable from the LCD (resolution and
Summary of the content on the page No. 11
Wall Mounting (Optional) ® To obtain a wall-mounting kit, contact ViewSonic or your local dealer. Refer to the instructions that come with the base mounting kit. To convert your LCD display from a desk- mounted to a wall-mounted display, do the following: 1. Verify that the Power button is turned Off, then Four VESA screw holes disconnect the power cord. 2. Lay the LCD display face down on a towel or blanket. 3. Remove the Plastic Covers from the back of the LCD display. 4. Remove the four s
Summary of the content on the page No. 12
Using the LCD Display Setting the Timing Mode Setting the timing mode is important for maximizing the quality of the screen image and minimizing eye strain. The timing mode consists of the resolution (example 1280 x 1024) and refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the OSD (On-screen Display) controls to adjust the screen image. For the best picture quality set your LCD display timing mode to: VESA 1280 x 1024 @ 60Hz. To set the Timing Mode: 1. Set
Summary of the content on the page No. 13
Adjusting the Screen Image Use the buttons on the front control panel to display and adjust the OSD controls which display on the screen. The OSD controls are explained at the top of the next page and are defined in “Main Menu Controls” on page 11. Main Menu with OSD controls Front Control Panel shown below in detail Scrolls through menu options and adjusts the displayed control. Also a shortcut to display the Contrast adjustment control screen. Displays the Main Displays the control screen
Summary of the content on the page No. 14
Do the following to adjust the display setting: 1. To display the Main Menu, press button [1]. NOTE: All OSD menus and adjustment screens disappear automatically after about 30 seconds. This is adjustable through the OSD timeout setting in the setup menu. 2. To select a control to adjust, press or to scroll up or down in the Main Menu. 3. After the desired control is selected, press button [2]. A control screen like the one shown below appears. The line at the bottom of the screen shows the
Summary of the content on the page No. 15
Main Menu Controls Adjust the menu items shown below by using the up and down buttons. Control Explanation Auto Image Adjust automatically sizes, centers, and fine tunes the video signal to eliminate waviness and distortion. Press the [2] button to obtain a sharper image. NOTE: Auto Image Adjust works with most common video cards. If this function does not work on your LCD display, then lower the video refresh rate to 60 Hz and set the resolution to its pre-set value. Contrast adjusts the diff
Summary of the content on the page No. 16
Control Explanation User Color Individual adjustments for red (R), green (G), and blue (B). 1. To select color (R, G or B) press button [2]. 2. To adjust selected color, press or . Important: If you select RECALL from the Main Menu when the product is set to a Preset Timing Mode, colors return to the 6500K factory preset. Information displays the timing mode (video signal input) coming from the graphics card in the computer, the LCD model number, the serial number, and ® the ViewSonic website
Summary of the content on the page No. 17
Control Explanation Setup Menu displays the menu shown below: The Setup Menu controls are explained below: Language Select allows the user to choose the language used in the menus and control screens. Resolution Notice advises the optimal resolution to use. OSD Position allows the user to move the OSD menus and control screens. OSD Timeout sets the length of time the OSD screen is displayed. For example, with a “15 second” setting, if a control is not pushed within 15 seconds, the display screen
Summary of the content on the page No. 18
Other Information Specifications LCD Type 19” (full 19" viewable diagonal area), TFT (Thin Film Transistor), Active Matrix SXGA LCD, 0.294 mm pixel pitch Color Filter RGB vertical stripe Glass Surface Anti-Glare Input Signal Video RGB analog (0.7/1.0 Vp-p, 75 ohms) Sync Separate Sync f :30-82 kHz, f :50-75 Hz h v Compatibility PC Up to 1280 x 1024 Non-interlaced 1 Macintosh Power Macintosh up to 1280 x 1024 Resolution Recommended 1280 x 1024 @ 60, 75 Hz and supported 1024 x 768 @ 60, 70, 75 Hz 8
Summary of the content on the page No. 19
Troubleshooting No power • Make sure power button (or switch) is ON. • Make sure A/C power cord is securely connected to the LCD display. • Plug another electrical device (like a radio) into the power outlet to verify that the outlet is supplying proper voltage. Power is ON but no screen image • Make sure the video cable supplied with the LCD display is tightly secured to the video output port on the back of the computer. If the other end of the video cable is not attached permanently to the LCD
Summary of the content on the page No. 20
Customer Support For technical support or product service, see the table below or contact your reseller. NOTE: You will need the product serial number. T = Telephone Country/Region Website Email F = FAX T= 800 688 6688 United States www.viewsonic.com service.us@viewsonic.com F= 909 468 1202 T= 866 463 4775 Canada www.viewsonic.com service.ca@viewsonic.com F= 909 468 5814 T= 866 323 8056 Latin America www.viewsonic.com soporte@viewsonic.com (Mexico/Chile) F= 909 444 5655 www.viewsoniceurope.com/
