Summary of the content on the page No. 1
CMS 801 Manual 21-6-07AW 28/9/07 10:03 Page 1
C M Y CM MY CY CMY K
CMS
CEILING MONITOR SYSTEMS
INSTALLATION MANUAL
CMS801 DC BM
CMS801 DC PI
CMS801 sub BM
CMS801 sub PI
CMS801 PI back can
Tannoy has a policy of continuous improvement and this specification sheet provides the latest information at the time of printing.
All specifications may be subject to further change. Please contact the Tannoy website for the latest information.
CMS
CMS801 TEMPLATE HOLE CUTOUT SIZE: 295mm (11.61”)
Composite
Summary of the content on the page No. 2
CMS 801 Manual 21-6-07AW 28/9/07 10:03 Page 2 C M Y CM MY CY CMY K 1. INTRODUCTION CONTENTS Thank you for purchasing this Tannoy Ceiling Monitor System product. This product range is suited 1 INTRODUCTION for high-level music and speech reinforcement applications requiring exceptional sonic quality with uncompromised reliability. 2 UNPACKING 2. UNPACKING 3 PRODUCT FEATURE IDENTIFICATION Every Tannoy product and accessory is carefully inspected before packing. After unpacking, please inspect yo
Summary of the content on the page No. 3
CMS 801 Manual 21-6-07AW 28/9/07 10:03 Page 3 C M Y CM MY CY CMY K 4. PRODUCT FEATURE IDENTIFICATION: 5. ACCESSORIES: Each product is supplied with the following accessories as standard: Conduit/Cable Clamp Tuning Port Euro Type Connector C-Ring Tile bridge kit Screws for mounting wings Note: A tile bridge kit Mounting Wings must always be used when installing into suspended ceiling tiles Rotary Switch Fig 1.1: The blind-mount (BM) models come with a pre-fitted back can Grille Cut-out template
Summary of the content on the page No. 4
CMS 801 Manual 21-6-07AW 28/9/07 10:03 Page 4 C M Y CM MY CY CMY K 5.1 MECHANICAL INSTALLATION GUIDE FOR SUSPENDED CEILINGS 5.2 MECHANICAL INSTALLATION GUIDE FOR SHEET-ROCK (PLASTER BOARD) CEILINGS Remove the ceiling tile from its frame and place it on a flat surface. Mark the Mark the cut-out area on the ceiling by tracing around the template provided. 1 1 cut-out area on the ceiling tile by tracing around the template provided. Cut out the hole in the ceiling using a circular saw or pad saw,
Summary of the content on the page No. 5
CMS 801 Manual 21-6-07AW 28/9/07 10:03 Page 5 C M Y CM MY CY CMY K 5.3 MECHANICAL INSTALLATION INSTRUCTIONS FOR OPTIONAL PLASTER RING: 5.4 INSTRUCTIONS FOR OPTIONAL PRE-INSTALLATION BACK CAN (PI MODELS ONLY): An optional plaster (mud) ring bracket is available from Tannoy. This bracket is designed to be pre-installed into newly AN OPTIONAL PRE-INSTALL BACK CAN IS AVAILABLE FOR ALL PI (PRE-INSTALL) MODELS. THIS BACK CAN IS DESIGNED TO constructed, non-suspended ceilings. BE PRE-INSTALLED INTO
Summary of the content on the page No. 6
CMS 801 Manual 21-6-07AW 28/9/07 10:03 Page 6 C M Y CM MY CY CMY K 6. WIRING AND SETTING UP: 7.1 CMS801 DC BM DIMENSIONS: TEMPLATE HOLE CUTOUT SIZE: 295mm Open the wiring cover at the back of the speaker can to access the Euro type connector 1 plug and socket. 327.8 286.4 310.5 [12.90"] [11.27"] [12.22"] For connection to an amplifier, use pins 1 and 2: 2 5.0 325.0 • Pin 1 is positive [0.20"] [12.80"] • Pin 2 is negative For connection to additional speakers in a distributed line, pins 3 an
Summary of the content on the page No. 7
CMS 801 Manual 21-6-07AW 28/9/07 10:03 Page 7 C M Y CM MY CY CMY K 7.4 CMS801 sub PI DIMENSIONS: 8.1 TECHNICAL SPECIFICATIONS: MODEL CMS801 DC TEMPLATE HOLE CUTOUT SIZE: 295mm System (1) Frequency response (-3dB) 47Hz - 30kHz Enclosure BM back can Back can Zinc plated steel Baffle Reflex loaded UL 94V-0 rated ABS (1) Frequency range (-10dB) 40Hz - 35kHz Grille Steel, with weather resistant coating BM back can Safety Features Safety ring located at rear of enclosure (1) Frequency range (-10dB) 4
Summary of the content on the page No. 8
CMS 801 Manual 21-6-07AW 28/9/07 10:03 Page 8 C M Y CM MY CY CMY K 8.2 TECHNICAL SPECIFICATIONS: 9. PAINTING System CMS801 sub Transducer If desired, the grille and baffle panel may be painted to match the surrounding décor. 1x 200mm (8.00") long throw woofer with (1) Frequency response (-3dB) 58Hz - 160Hz multi fibre paper pulp cone Painting the baffle: (1) Frequency range (-10dB) 42Hz - 300Hz Physical Caref
Summary of the content on the page No. 9
CMS 801 Manual 21-6-07AW 28/9/07 10:03 Page 9 C M Y CM MY CY CMY K 11. DECLARATION OF CONFORMITY: NOTES The following apparatus is manufactured in China for Tannoy Ltd of Rosehall Industrial Estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed and constructed such that electromagnetic disturbances generated do not exceed level
Summary of the content on the page No. 10
CMS 801 Manual 21-6-07AW 28/9/07 10:03 Page 10 C M Y CM MY CY CMY K NOTES NOTES 18 19 Composite CMS
