Summary of the content on the page No. 1
User Manual
1760Series
Component Waveform/
Vector Monitor
070-8473-05
Thisdocumentsupportsfirmwareversion 2.2 and
above.
www.tektronix.com
Summary of the content on the page No. 2
Copyright© Tektronix, Inc. All rightsreserved. Tektronix productsare covered by U.S. and foreign patents, issued and pending. Information in thispublication supercedesthat in all previously published material. Specificationsand price change privilegesreserved. Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077 TEKTRONIXand TEKare registered trademarksof Tektronix, Inc.
Summary of the content on the page No. 3
WARRANTY Tektronix warrants that this product will be free from defects in materials and workmanship for a period of three (3) years from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product. In order to obtain service under this warranty, Customer must notify Tektronix of the defect before th
Summary of the content on the page No. 4
Summary of the content on the page No. 5
GeneralSafetySummary Reviewthe following safety precautionsto avoid injury and prevent damage to thisproduct or any productsconnected to it. To avoid potential hazards, use thisproduct only asspeci- fied. Only qualified personnel should perform service procedures. ToAvoidFireorPersonalInjury UseProperPowerCord Use only the power cord specified for thisproduct and certi- fied for the country of use. ConnectandDisconnectProperly Do not connect or disconnect probesor test leadswhile they are connec
Summary of the content on the page No. 6
GeneralSafetySummary The common terminal isat ground potential. Do not connect the commonterminal toelevatedvoltages. DoNotOperateWithoutCovers.Do not operate this product with coversor panelsremoved. UseProperFuse.Use only the fuse type and rating speci- fied for thisproduct. AvoidExposedCircuitry.Do not touch exposed connec- tionsand componentswhen power ispresent. DoNotOperateWithSuspectedFailures.If you suspect there isdamage to thisproduct, have it inspected by qualified service personnel.
Summary of the content on the page No. 7
GeneralSafetySummary CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property. TermsontheProduct.These termsmayappearonthe product: DANGER indicatesan injury hazardimmediatelyaccessible asyou read the marking. WARNINGindicatesaninjuryhazardnot immediatelyac- cessible asyou read the marking. CAUTIONindicatesa hazard to property including the prod- uct. SymbolsontheProduct.These symbolsmay appear on the product: Double CAUTION WARNI
Summary of the content on the page No. 8
GeneralSafetySummary iv 1760SeriesComponentWaveform/VectorMonitorUserManual
Summary of the content on the page No. 9
TABLE OF CONTENTS Introduction Product Description ............................ 1-1 Features ................................. 1-2 Options....................................... 1-5 Option SC ............................... 1-5 Power Cord Options....................... 1-5 CRT Options ............................. 1-6 Accessories................................... 1-7 Standard Accessories ..................... 1-7 Optional Accessories ...................... 1-7 Field Upgrade Kits ...............
Summary of the content on the page No. 10
TableofContents GettingStarted At A Glance ................................... 2-1 Front-Panel Controls ...................... 2-1 Rear-Panel Connectors .................... 2-8 Operator’s Checkout Procedure ................. 2-11 Required Equipment .................... 2-11 Initial Equipment Connections............ 2-12 Procedure ............................... 2-13 OperationBasics Functional Overview............................ 3-1 Display Modes............................ 3-1 Vector..........
Summary of the content on the page No. 11
TableofContents Filter Menu ............................... 3-9 Cursor Menu ............................. 3-10 Waveform Cursor Control................ 3-11 Vector + Waveform (Multiple)............ 3-13 Using the Cursors......................... 3-13 Line Select Menu ......................... 3-16 Preset Menu ............................. 3-18 Configure Menu .......................... 3-20 INPUT................................. 3-20 VECTOR .............................. 3-21 FORMAT ..............
Summary of the content on the page No. 12
TableofContents Chroma Bandwidth ..................... 4-8 DifferentialPhase and Gain .............. 4-8 Making SCHPhase Measurements ......... 4-9 NTSC ................................. 4-9 PAL ................................... 4-11 SCH R---Y ............................. 4-11 Making AudioMeasurements............... 4-14 Lightning Measurements................... 4-15 Using the Diamond Display ................ 4-17 Using the Bowtie Display .................. 4-19 Time Code Display ............
Summary of the content on the page No. 13
LISTOFFIGURES Figure 2-1 Multi-Use Bezel Controls and Buttons. ...... 2-2 Figure 2-2 1760 Front Panel ..................... 2-3 Figure 2-3 1760--Series Rear Panel ................ 2-10 Figure 2-4 Equipment hook-up for Operator’s Checkout Procedure .......................... .2-12 Figure 2-5 Component waveform display (A123) ....... 2-14 Figure 2-6 Calibrator display ..................... 2-15 Figure 2-7 Two-Line LUM filter display of color bar signal . 2-18 Figure 2-8 Two-Line CHROM filter displ
Summary of the content on the page No. 14
Figure 4-1 NTSC waveform/vector graticule .......... 4-2 Figure 4-2 PAL waveform/vector graticule ............ 4-3 Figure 4-3 Dual Standard waveform/vector graticule .... 4-4 Figure 4-4 Vector targets ........................ 4-7 Figure 4-5 Differential gain and phase measurements ... 4-9 Figure 4-6 NTSC dual-dot SCH display ............. 4-11 Figure 4-7 NTSC single-dot SCH display ............ 4-11 Figure 4-8 PAL SCH display ..................... 4-12 Figure 4-9 Two-Line SCH R--Y display (NTSC)
Summary of the content on the page No. 15
Preface Thisuser manual isone of a set of two manualsthat document the Tektronix 1760-SeriesComponent Waveform/Vector monitors. To purchase a service manual, please refer to “Contacting Tektronix” on Page xiv for addressand phone number information. UserManual Instrument controlsand readoutsappear in ALLCAPITALS. Topicscovered in the user manual are asfollows: Introduction GettingStarted OperationBasics MakingMeasurements Appendix A providesinstrument specifications, both electrical andmechanica
Summary of the content on the page No. 16
Preface ServiceManual Topicscovered in the service manual are asfollows: Specifications OperatingInformation Theory ofOperation PerformanceVerification Adjustment Procedures Maintenance Options Electrical PartsList Diagrams Mechanical PartsList xii 1760SeriesComponentWaveform/VectorMonitorUserManual
Summary of the content on the page No. 17
Preface 1761ComponentWaveform/VectorMonitor. 1760SeriesComponentWaveform/VectorMonitorUserManual xiii
Summary of the content on the page No. 18
Preface Contacting Tektronix Phone 1-800-833-9200* Address Tektronix, Inc. Department or name (if known) 14200 SW Karl Braun Drive P.O. Box 500 Beaverton, OR 97077 USA Web site www.tektronix.com Sales 1-800-833-9200, select option 1* support Service 1-800-833-9200, select option 2* support Technical Email: techsupport@tektronix.com support 1-800-833-9200, select option 3* 6:00a.m. -- 5:00p.m. Pacific time * This phone numberis toll free in North America. Afteroffice hours, please leave a voice m
Summary of the content on the page No. 19
Introduction
Summary of the content on the page No. 20
