Summary of the content on the page No. 1
PN-E802
LCD MONITOR
OPERATION MANUAL
Summary of the content on the page No. 2
IMPORTANT: To aid reporting in case of loss or theft, please record the Model No.: product’s model and serial numbers in the space provided. The numbers are located in the rear of the product. Serial No.: U.S.A. ONLY
Summary of the content on the page No. 3
IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within a triangle, is intended to alert the user to the CAUTION presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of RISK OF ELECTRIC sufficient magnitude to constitute a risk of electric SHOCK shock to persons. DO NOT OPEN The exclamation point within a triangle is intended to alert th
Summary of the content on the page No. 4
DEAR SHARP CUSTOMER Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product. SAFETY PRECAUTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in
Summary of the content on the page No. 5
SAFETY PRECAUTIONS (Continued) 19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment, dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below: • Use the specified batteries only. • Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the compartment. • Do not mix old and new ba
Summary of the content on the page No. 6
TIPS AND SAFETY INSTRUCTIONS - The TFT color LCD panel used in this monitor is made with The Power Cord the application of high precision technology. However, there - Use only the power cord supplied with the monitor. may be minute points on the screen where pixels never light - Do not damage the power cord nor place heavy objects on or are permanently lit. Also, if the screen is viewed from it, stretch it or over bend it. Also, do not add extension cords. an acute angle there may be une
Summary of the content on the page No. 7
MOUNTING PRECAUTIONS • This product is for use indoors . • Adhere to the following when installing the monitor in its • A mounting bracket compliant with VESA specifications is portrait orientation. Failing to adhere to the following may required. cause malfunctions. • Since the monitor is heavy , consult your dealer before - Install the monitor such that the power LED is located on installing, removing or moving the monitor . the bottom si
Summary of the content on the page No. 8
Contents IMPORTANT INFORMATION ............................................3 Menu Items .....................................................................19 DEAR SHARP CUSTOMER ..............................................4 Displaying the menu screen .......................................19 SAFETY PRECAUTIONS....... ...........................................4 Menu item details .......................................................20 TIPS AND SAFETY INSTRUCTIONS ...........................
Summary of the content on the page No. 9
Part Names nFront view 1. LCD panel 2. Remote control sensor (See page 14.) 3. Input switch (See page 17.) 4. Power switch (See page 15.) 5. Power LED (See page 15.) 1 TIPS • Use a pointed object such as a pen tip to press the switches at the front of the monitor. 23 45 nRear view 1. Optional attachment section When the PN-ZB01 This section is used to connect optional (optional) is attached hardware for function expansion. 15 Offering this attachment location is not a guarantee that fu
Summary of the content on the page No. 10
Part Names nRemote control unit 1. Signal transmitter 1 2. POWER button (See page 15.) 3. MUTE button (See page 17.) 4. VOL +/- buttons (See page 17.) BRIGHT +/- buttons (See page 17.) Cursor control ( / / / ) buttons 7 2 5. DISPLAY button (See page 17.) 6. MODE button (See page 17.) 3 8 7. INPUT button (See page 17.) 8. MENU button (See page 17.) 4 9. SIZE button (See page 17.) 5 9 6 E 10
Summary of the content on the page No. 11
Connecting Peripheral Equipment When the PN-ZB01 (optional) is attached 6 14 12 13 11 1 8 7 9 2 10 3 4 5 5 Caution Connection with a PC or AV equipment • Be sure to turn off the main power switch and disconnect 1. PC/AV HDMI input terminal the plug from the power outlet before connecting/ • Use a commercially available HDMI cable (conforming to disconnecting cables. Also, read the manual of the the HDMI standard). equipment to be connected. • Set HDMI of INPUT SELECT on the OPTION menu • Be
Summary of the content on the page No. 12
Connecting Peripheral Equipment 13. External speaker terminals Connection when the PN-ZB01 • To use external speakers, set SPEAKER SELECT on the (optional) is attached SETUP menu to EXTERNAL. • Be sure to use external speakers with an impedance of 6 Ω The PN-ZB01 expansion board (optional) allows the use of or greater and a rated input of at least 7 W. additional connection terminals. 13 2 6. PC/AV DVI-D input terminal Approx. • Set DVI of INPUT SELECT on the OPTION menu 3-15/16 inch accor
Summary of the content on the page No. 13
Connecting the Power Cord Caution • Use only the power cord supplied with the monitor. 1. Turn off the main power switch. 2. Plug the power cord (supplied) into the AC input terminal. 3. Plug the power cord (supplied) into the AC power outlet. 3 For power Main power switch outlet 1 2 AC input terminal Power cord (Supplied) Binding Cables The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp. Attach the cable clamp into the cable clamp attachment
Summary of the content on the page No. 14
Preparing the Remote Control Unit Installing the batteries Remote control operation range 1. Press the cover gently and slide it in the direction of the The operation range of the remote control unit is approx. 16.4 arrow. feet (5 m) at an angle of approx 10° from the center to the top/ bottom/right/left of the remote control sensor. 2. See the instructions in the compartment and put in the Remote supplied batteries (R-6 (“AA” size) x 2) with their plus (+) control sensor and minus (-) sides
Summary of the content on the page No. 15
Turning Power On/Off Caution Turning power on/off • Turn on the monitor first before turning on the PC or Press the POWER button or POWER switch to turn the power playback device. ON/OFF. Turning on the main power Main power switch Power LED Status Status of the monitor Green lit Power on Orange lit Power off (Standby mode) Green flashing Input signal waiting mode Caution • The main power must be turned on/off with the main power Caution switch. Do not connect/disconnect the power cord or tur
Summary of the content on the page No. 16
Turning Power On/Off nDate/time setting Disabling power on/off operations • If the time has yet to be set when the monitor is first turned Power on/power off operations can be disabled in order to on, the date/time setting screen appears. Set the date and protect the monitor from an accidental power off. Set the time. ADJUSTMENT LOCK in FUNCTION menu to “ON 2”. (See page 28.) DATE/TIME SETTING // : : SET 01 / 01 / 20 12 12 : 00 AM CANCEL OK···[MENU] 1. Press , , or to select the da
Summary of the content on the page No. 17
Basic Operation 2. MUTE Turns off the volume temporarily. Press the MUTE button again to turn the sound back to the 1 previous level. 3. MENU 2 Displays and turns off the menu screen. (see page 19.) 3 4 4. VOL +/- (Volume adjustment) Pressing or displays the VOLUME menu when the 5 menu screen is not displayed. VOLUME 15 Press or to adjust the volume of the sound. 6 7 * If you do not press any buttons for about 4 seconds, the VOLUME menu automatically disappears. 8 5. BRIGHT +/- (Ba
Summary of the content on the page No. 18
Basic Operation nSwitching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE PC input Displays image so it fills the entire screen. AV input An image with a 4:3 aspect ratio is stretched to fill the entire screen. ZOOM 1 PC input An image with a 4:3 aspect ratio is enlarged to fill the entire screen without changing the aspect ratio. The edges of the image may be cut off. AV input ZOOM 2 PC input Use this size if ZOOM 1 c
Summary of the content on the page No. 19
▲ ▲ ▲ ▲ Menu Items TIPS Displaying the menu screen • The menu will differ depending on the input mode. Video and audio adjustment and settings of various functions • The menu screen will close automatically if no operation is are enabled. This section describes how to use the menu performed for about 15 seconds. (DATE/TIME SETTING, items. See pages 20 to 24 for details of each menu items. SCHEDULE and LAN SETUP screens will close in about 4 minutes.) Caution Menu screen display • Do not tur
Summary of the content on the page No. 20
Menu Items nPICTURE Menu item details You can move the menu screen display position each time The menu will differ depending on the input mode. DISPLAY is pressed. nSCREEN AUTO (PC D-SUB/PC RGB) You can move the menu screen display position each time The ANALOG GAIN and ANALOG OFFSET are DISPLAY is pressed. automatically adjusted. Pressing performs adjustment. AUTO (PC D-SUB/PC RGB) ANALOG GAIN (PC D-SUB/PC RGB) The CLOCK, PHASE, H-POS, and V-POS are automatically Adjusts the bright por
