Summary of the content on the page No. 1
LCD MONITOR
LCD FARBMONITOR
MONITEUR LCD
MONITOR LCD
MONITOR LCD
LL-T1803-H
LL-T1803-B
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUALE D’USO
MANUAL DE FUNCIONAMIENTO
Summary of the content on the page No. 2
Table of Contents / Inhaltsverzeichnis / Table des matières / Indice / Índice English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
Table of Contents Notice for Users in the USA ............................................................................................................................ 4 TCO '95/ '99 ..................................................................................................................................................... 5 Notice for Users in Europe ............................................................................................................................... 7 Notic
Summary of the content on the page No. 4
Notice for Users in the USA FCC Statement WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Summary of the content on the page No. 5
LL-T1803-B LL-T1803-H Congratulations! You have just purchased a TCO’95 or TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. This product meets the requirements for the TCO’95 or TCO’99 scheme which provides for an international environmental and quality labelling of person
Summary of the content on the page No. 6
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chlorid
Summary of the content on the page No. 7
Notice for Users in Europe This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/ EEG. Dette udstyr overholder
Summary of the content on the page No. 8
Notice for Users in the UK FOR CUSTOMERS IN U.K. IMPORTANT The wires in this mains lead are coloured in accordance with the following code : GREEN-AND-YELLOW : Earth BLUE : Neutral BROWN : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows. The wire which is coloured GREEN- AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safe
Summary of the content on the page No. 9
Tips and safety precautions Monitor and accessory checklist - Under certain display conditions, minute specks or spots may be noticeable. This is common for - Please check that the following items are included in the package. liquid crystal monitors and is not a malfunction. - The LCD panel has been manufactured using - LCD monitor (1) - AC adapter (1) highly elaborate technology. Properly working pixels comprise 99.99% of total pixels. However, (model name: NL-A61J) - Analog signal cable (1) pl
Summary of the content on the page No. 10
Product description 11 11 11 78 9 10 1 2 3 4 5 6 1. INPUT button ............................ To switch between the signal’s input terminals. (Analog signal input terminal ↔ DVI-D input terminal) 2. MENU button ............................ This button is used to pop-up, select and close the OSD (On Screen Display) Menu. 3. SELECT button ........................ This button is used to select menu options when the OSD Menu is dis- played. 4. buttons .............................. When the OSD Men
Summary of the content on the page No. 11
Product description Standing up and adjusting the monitor CAUTION! - Pressure from hands on the LCD panel could cause damage. - Be careful not to allow your fingers to be pinched. Standing up the monitor Press down on the stand and lift up the top section of the monitor. Folding up the monitor 1. Remove the AC adapter and the RGB signal cable. 2. If carrying out adjustments to the monitor, place it upright. 3. While pressing the rear lock disable button (1), gently fold back the monitor (2). (2
Summary of the content on the page No. 12
Connecting the monitor and turning the monitor on and off CAUTION! Digital RGB connection Connecting the monitor to a computer via a Digital - When connecting, ensure that both the monitor signal cable. (to be purchased separately) and computer are switched off. - For digital RGB connection, the monitor has an - Be careful not to overly bend the cable or add input for connecting to a computer with a DVI- extension cords as this could lead to a compatible output connector (DVI-D 24 pin or DVI- m
Summary of the content on the page No. 13
Connecting the monitor and turning the monitor on and off CAUTION! Turning the power off - After unplugging the AC adaptor or power cord, be sure to wait at least 10 seconds before plugging 1. Turn the computer off. in again. If you put the plug back in immediately 2. Press the monitor's POWER button. after unplugging, damage may be caused and the The Power LED will disappear. screen malfunction or not display. Turn the Turning the power on computer off Press power button OFF 1. Press the monit
Summary of the content on the page No. 14
Adjusting the screen display For analog signal Adjustment lock function 1. First perform an automatic adjustment. (p. 15) 2. Perform manual adjustment where necessary. By disabling the control buttons (i.e. setting the lock) (p. 16) any attempted changes to adjusted values will be For digital signal voided. The monitor can generally be used without 1. Turn off the monitor power. adjustment. If necessary perform manual 2. While pressing the MENU button, press the adjustment. (p. 19) power button
Summary of the content on the page No. 15
Adjusting the screen display (With analog connection) How to Adjust Automatic screen adjustment 1. Press the MENU button. Options in the ADJUSTMENT Menu can be adjusted The ADJUSTMENT Menu will be displayed. automatically (CLOCK, PHASE, H-POS V-POS). Note: - When setting up this monitor for the first time or after having changed an aspect of the current system, perform an automatic screen adjustment before use. 2. Press the button. On Screen Display for the automatic The screen will become da
Summary of the content on the page No. 16
Adjusting the screen display (With analog connection) ADJUSTMENT Menu Manual screen adjustment Adjustments can be made using On Screen Display (OSD) Menu provided. On Screen Display for adjustment If you are using Windows, open the Adjustment Pattern on the accompanying Utility Disk. (p. 15). MANUAL: Individual menu options are manually If your system is not Windows, you can not use the adjusted. Adjustment Pattern. Therefore display an image that makes the entire screen light and adjust it th
Summary of the content on the page No. 17
Adjusting the screen display (With analog connection) GAIN CONTROL Menu WHITE BALANCE Menu MANUAL: Individual menu options are manually adjusted. Notes: AUTO: Every menu option is automatically - On settings other than [STD] not all graduations adjusted using the Auto Gain Control* can be displayed. To display all graduations, set function. to [STD]. - Use the buttons to select [COOL], [·], [STD], Notes: [·], [WARM] or [USER]. - Press the button to select [AUTO]. - Selecting USER will displ
Summary of the content on the page No. 18
Adjusting the screen display (With analog connection) MODE SELECT Menu Notes: - Depending on the resolution of the input signal, even if menu options can be selected, the display may not change. - To choose a menu option: SELECT button - When adjustment complete: MENU button OSD H-POSITION (OSD horizontal position) The position of the OSD display can be moved to the left and right. ( buttons) OSD V-POSITION (OSD vertical position) The position of the OSD display can be moved up and down. ( b
Summary of the content on the page No. 19
Adjusting the screen display (With digital connection) Adjustments can be made using On Screen Display WHITE BALANCE Menu (OSD) Menu provided. On Screen Display for adjustment If you are using Windows, open the Test Pattern on the accompanying Utility Disk. (p. 15) If your system is not Windows, you can not use the Adjustment Pattern. Therefore display an image that makes the entire screen light and adjust it through Notes: checking visually its actual tone. - On settings other than [STD] not
Summary of the content on the page No. 20
Adjusting the screen display (With digital connection) MODE SELECT Menu Notes: - Depending on the resolution of the input signal, even if menu options can be selected, the display may not change. - To choose a menu option: SELECT button - When adjustment complete: MENU button OSD H-POSITION (OSD horizontal position) The position of the OSD display can be moved to the left and right. ( buttons) OSD V-POSITION (OSD vertical position) The position of the OSD display can be moved up buttons) an
