Summary of the content on the page No. 1
SyncMaster 753s/753v/753DFX/753DF/750S
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock
Summary of the content on the page No. 4
When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CDT. Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electr
Summary of the content on the page No. 5
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause injury by falling. Set down the monitor carefully. It could be damaged or broken. Do not place the m
Summary of the content on the page No. 6
When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.) Dilute the detergent (1:10 ratio) with water before using. Do not spray detergent directly on the monitor.
Summary of the content on the page No. 7
Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or a fire. Do not place any heavy objects on the monitor. This may cause an electric shock or a fire. For each hour
Summary of the content on the page No. 8
Keep the monitor away from any magnetic substances. This may cause discoloring or distortion of the image.
Summary of the content on the page No. 9
Monitor and Stand Power Cord Stand Quick Setup Guide (Some models include a stand attached. ) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Warranty Card (Not available in all locations) User's Guide and Driver Installation CD
Summary of the content on the page No. 10
1. Exit button Use this button to Exit the active menu or the OSD. 2,3. Adjust buttons These buttons allow you to highlight and adjust items in the menu. 4. Menu button Use this button to open the OSD and activate a highlighted menu item. 5. Power indicator This light glows green during normal operation, and blinks green once as the monitor saves your adjustments. Use this button to turn the monitor on and off. 6. Power button Note: See PowerSaver described in the manual for further informatio
Summary of the content on the page No. 11
(The configuration at the back of the monitor may vary from product to product.) Connect the power cord for your monitor to the power port on the back of 1. Power port the monitor. 2. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. See Connecting Your Monitor for further information regarding cable connections. Note:
Summary of the content on the page No. 12
Connect the signal cable to the video port on your computer, video board, 1. Signal Cable video card, or graphics card. 2. Power port Connect the power cord for your monitor to the power port on the back of the monitor. You can separate the base from the monitor. 3. Tilt/Swivel Base
Summary of the content on the page No. 13
1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter(Adapter not included). A PC-compatible computer does not need an adapter. 4. Turn on your computer and monitor. If your moni
Summary of the content on the page No. 14
Automatic Manual When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ (WorldWide) http://www.samsungusa.com/monitor/ (USA) http://www.se
Summary of the content on the page No. 15
4. Click the "Install" button in the "Warning" window. 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. * This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 6. Monitor driver installation is completed. file://\\yklee\en_ko\ko\setup\se_drive.htm 1/7/2003
Summary of the content on the page No. 16
Automatic Manual Windows XP | Windows 2000 | Windows Me | Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/
Summary of the content on the page No. 17
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
Summary of the content on the page No. 18
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" windo
Summary of the content on the page No. 19
How to install 1. Click " " , " " , " ". Start Setting Control Panel 2. Double click the " " Icon. Display 3. Choose the " " tab and then click " ". Settings Advanced.. 4. Choose "Monitor". Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. 5. Click "Driver" and then click on "Update Driver.." then click on th
Summary of the content on the page No. 20
With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle. Note: The base is detachable. Attaching the Base 1. Place the monitor upside-down on a flat work surface. 2. Align the tabs on the base with the corresponding slots on the bottom of the monitor. 3. Press the base onto the monitor until the tabs are fully engaged in the slots. 4. Push the base toward the front of the monitor until the release latch clicks into the locked posii ition.
