Summary of the content on the page No. 1
SyncMaster 214T
Install drivers Install programs
Summary of the content on the page No. 2
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.
Summary of the content on the page No. 3
Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not excessively bend the plug and wire nor pl
Summary of the content on the page No. 4
Do not drop the monitor when moving it. This may cause damage to the product or human body. Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or personal injury. Do not place the product on an unstable or small surface area. Place the product on an even, stable surface, as the product may fall and cause harm to someone walking by, specifically chi
Summary of the content on the page No. 5
Do not place the monitor face down. The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10cm/4inch ) for ventilation purposes. Poor ventilation may cause an increase in the internal temperature of the product, resultin
Summary of the content on the page No. 6
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Contact the Service Center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire. Others Do not remove cover (or b
Summary of the content on the page No. 7
Do not try to move the monitor by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or sma
Summary of the content on the page No. 8
Adjust the resolution and frequency to the levels appropriate for the model. Inappropriate resolution may cause undesirable picture quality. 21 inch (54cm) - 1600 X 1200 @ 60 Hz Watching the monitor continuously at a too close angle may result in eyesight damage. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations. Dropping the product
Summary of the content on the page No. 9
HAS Stand : Height Adjustable & Pivot Stand (214T : 100mm) PIP/PBP : Uses MagicTune to adjust PIP for the best viewing position Adopts MagicColor Pro to make adjustments of a variety of colors at an expert level Color Weakness : Enables those with color weakness to view the screen as easily as those with normal vision. Auto Rotation applied (Implemented by MagicRotation) SyncMaster 214T Please make sure the following items are included with your monitor. If any items are missing, conta
Summary of the content on the page No. 10
User's Guide, Monitor Driver, Warranty Card Quick Setup Guide Natural Color, MagicTune™, (Not available in all locations) MagicRotation software Cable D-sub Cable Power Cord DVI Cable Sold separately S-Video Cable Video Cable Set-Bracket Screws (4EA) Front
Summary of the content on the page No. 11
MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. Adjust buttons [ ] These buttons allow you to adjust items in the menu. Analog/Digital(PC) : MagicBright™ is a new feature providing the optimum viewing MagicBright™ button environment depending on the contents of the image you are [] watching. Currently four different modes are available: Custom, Entertain, Internet, and Text. Each mode has its own pre- configured brightness valu
Summary of the content on the page No. 12
provides a sharp image. 3) Movie Select this mode when the surroundings are dark. This will save power and reduce eye fatigue. 4) Custom Select this mode when you want to adjust the image according to your preferences. >>Click here to see an animation clip Brightness button [ ] ( Available in Analog Mode Only ) When OSD is not on the screen, push the button to adjust brightness. >>Click here to see an animation clip Enter button [ ] / Activates a highlighted menu item. / S
Summary of the content on the page No. 13
POWER S/W : Switch the monitor on and off. POWER IN : Connect the power cord for your monitor to the POWER IN on the back of the monitor. DVI IN (Source List : Digital) : Connect the DVI cable to the DVI IN port on the back of your monitor. RGB IN (Source List : Analog) : Connect the signal cable to the 15-pin, RGB IN port on the back of your monitor. VIDEO (Source List : Video)
Summary of the content on the page No. 14
: External device (video) input terminal S-VIDEO (Source List : S-Video) : External device (S-video) input terminal Kensington Lock : The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it. Stand Height Adjustment 1. Press the top side of the stand and then push the button at the rear bottom of the stand. 2. Press th
Summary of the content on the page No. 15
Connecting the Monitor 1. Connect the power cord for your monitor to the POWER IN on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, RGB IN port on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI cable to the DVI IN port on the back of your monitor. 2-3. Connected to a Macintosh. Connect the monit
Summary of the content on the page No. 16
Cable Fix Ring. Connecting to Other devices This monitor allows the user to connect it to such input devices as a DVD player, a VCR or a camcorder without disconnecting the PC. The configuration at the back of the monitor may vary from product to product. 1. Connecting AV Devices The monitor has AV connection terminals to connect AV input devices like DVD, VCR or Camcorder. You may enjoy AV signals as long as the monitor is turned on. 1. Input devices such as DVD, VCR or Camco
Summary of the content on the page No. 17
1. Input devices such as digital DVD are connected to the DVI IN terminal of the monitor using the DVI cable. 2. Then, start the DVD with a DVD disc inserted. 3. Select Digital using the SOURCE button. Using the Stand Pivot Stand
Summary of the content on the page No. 18
Using (a), you can rotate the screen within a range of 0 ~ 90 degrees. Using (b), you can use the screen lengthwise. Press the top side of the stand and then push the button at the rear bottom of the stand. You can adjust the stand height using this button. When you are using a stand height as maximum, it will go down a little bit from spring elasticity. If you rotate the screen without lifting it to its maximum height, the screen may be damaged because the edge of the screen would
Summary of the content on the page No. 19
A. Monitor B. Mounting interface pad (sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface Pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base. To mount the monitor on
Summary of the content on the page No. 20
4. Click the "Install" button in the "Warning" window. 5. Monitor driver installation is completed. Windows XP/2000 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button. 4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage
