Summary of the content on the page No. 1
KS - 6812
Fan Free Touch Terminal
User’s Manual
Rev.: Original
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operate
Summary of the content on the page No. 2
ALERT TO OUR HONORABLE CUSTOMERS: Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences. This product contains inside a Lithium battery. Please always follow local environmental protection laws / regulations for disposal of used batteries and always replace only with battery of same type. DAILY MAINTENANCE GUIDE For regular cl
Summary of the content on the page No. 3
INTRODUCTION PRODUCT PICTURES Front View Rear View 1 1 6 2 7 3 8 5 4 9 Side Views 10 5 14 11 13 7 12 15 13 Bottom View Inside Base 16 17 18 19 20 PARTS IDENTIFICATION 1. Main unit 2. Touch panel / LCD panel 3. Power indicator 4. Base stand Part 3
Summary of the content on the page No. 4
5. Optional side mount kit 6. HDD cover CF memory card reader 7. Hinge cover 8. Base back cover 9. Cable exit 10. Power switch 11. LCD brightness up button 12. LCD brightness down button 13. Base back cover hook 14. USB ports on left side 15. Sundries trough for pencils, paper clips etc. 16. Rubber feet with fixing screws 17. Screw holes for base mount kit 18. Oval cable passage on cast base trunk 19. Cable tie for all cables 20. Screw posts for optional HDD in base PRODUCT FEA
Summary of the content on the page No. 5
5. one VGA port 6. one SATA data port plus one HDD power connector for optional SATA HDD in base eSATA 7. one audio jack for stereo line output 8. one CR port capable of controlling 2 cash drawers max. 9. one 2 pin type DC 12 V power input connector 10. reserved one LPT interface through use of optional special cable in service window k) Built-in 1 internal 2W speaker l) Touch control functions: left/right button, double click, drag & draw m) Dynamic video memory technology up to 224
Summary of the content on the page No. 6
INSTALLATION GUIDES CAUTION: Before any installation or cable connection to the set, please always make certain that the system is turned off and the external power source to the set is removed to prevent electric hazard! Never touch any metal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage unless the operator is well grounded. Failure to do the above will void the product warranty! TECHNICAL MANEUVERS Applicable technical maneuvers in KS
Summary of the content on the page No. 7
OPENING BASE BACK COVER In order to settle the touch terminal properly in a point of sale system, all the cable connections have to be routed through its base. Therefore, please observe the side view pictures of the base trunk at the left and release the triangle marked hooks to remove the back cover. CABLE ROUTING IN BASE For cable routing in the mini slim base, please refer to the picture at left. There is a cable tie inside the base trunk as arrowed in the picture. Hold all the e
Summary of the content on the page No. 8
PREPARING THE MAIN UNIT On the back of the main unit, there is a service window facing the base trunk in most of application. It is recommended to tilt the LCD panel to most backward position and rest the surface of LCD panel over a piece of soft clean cloth on a desktop to access the service window. Use a screw driver of adequate length to remove the service window Service Window lock screw to open the cover plate and find several Lock Screw jumpers as illustrated in the lower right
Summary of the content on the page No. 9
The KS system will directly control the cash drawer using the cash drawer port (CR) both to operate the opening mechanism and to monitor the drawer open status. Both functions may be accomplished under software control of the COM1 serial port. Use the cable supplied with the cash drawer (Part No. 21863018010) for connection to the CR port in KS system. This cable has a 6-pole plug at one end and an 8-pole plug at the other. The 8-pole plug should be inserted into the connector marked: “
Summary of the content on the page No. 10
OPERATING SYSTEM RECOVERY For KS-6812 systems with operating system in the Compact Flash Card if the system is installed with the CF card reader, once the Compact Flash is damaged for any reason, the thin client may fail to boot. A bootable new Compact Flash Card will be required to have the workstation back to work. Please follow instructions given by the System Integrator to deal with situations like that. One more advice for CF Card application is that in spite of the fact that it is
Summary of the content on the page No. 11
USING THE TOUCH TERMINAL APPLICATION ENVIRONMENT It is very important that you check the following operational guidelines: Ventilation This terminal must NOT be operated in an environment with restricted ventilation. There must be at least 25 mm air clearance around any top or side ventilation holes with a free flow of air around the unit at ALL times for the installation. Operating Environment The equipment must not be operated or stored in extremes of both temperature and humidity/moi
Summary of the content on the page No. 12
for within 10 seconds. There must always be at least 10 seconds waiting before switching on again once the system is powered off successfully. Automatic Power On Control The system may also turn on according to some preset conditions such as Modem Ring Up or Alarm Clock Wake Up or LAN Wake Up. To utilize Modem Ring Up or Alarm Clock Wake Up function, the user should enter the BIOS setup by pressing “Del” key at system boot up, choose in “Power Management Setup” and make the “Power On by
Summary of the content on the page No. 13
CUSTOMER DISPLAY Please follow the instructions on the manual that comes along with the customer display when it is installed. DISPLAY ISSUES Main LCD Display For best viewing result please set your display resolution at 1024 x 768 with high color. The system Video Memory is shared from system memory. The video memory size is default 8 MB and can be set to be 1 MB. VGA Port The VGA port in the KS-6812 system supports either a base mount nd 2 display or a separately connected LCD monitor
Summary of the content on the page No. 14
CF MEMORY CARD READER If the CF card reader is installed and the CF card is used for system data storage device, it is recognized by the system as the IDE channel 1 Master device. The CF memory card reader inside main unit accepts a type II CF memory card. Please note that usual utilities such as FDISK.EXE or FORMAT.COM must never be used on CF card or permanent damage can occur. If this option is installed, the standard SATA HDD in main unit is not applicable. HDD & SATA PORT The 2.5”
Summary of the content on the page No. 15
Posiflex USB Touch Manager A program named “Posiflex USB Touch Manager” and a right-click sticky button tool in the program group “Posiflex USB Touch Tools” is installed in the preloaded Windows system with a USB interface touch panel controller. This program can also be obtained by download from the POSIFLEX web site. Part 15
Summary of the content on the page No. 16
nd 2 Monitor nd The 2 LCD display monitor LM- 3112 can be attached to the rear edge of base bottom of KS-6812 series if no pole display is attached. Refer to the picture at left. Use the 2 attached screws to fix the metal base of the LM to the bottom plate of mini slim base at the circled positions. Connect the VGA cable to go through the cable exit to the VGA port after the +12V DC support in KS-6812 is enabled. Part 16
Summary of the content on the page No. 17
Part 17
Summary of the content on the page No. 18
Part 18
Summary of the content on the page No. 19
Part 19
Summary of the content on the page No. 20
T31454 Part 20
