Summary of the content on the page No. 1
TM4000 Series
Touch Monitor
. : A
I. FE
•
•
•
•
•
•
•
•
•
•
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to
comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial enviro
Summary of the content on the page No. 2
II. TM4012: 12.1” LCD Monitor w/ standard touch panel and PS/2 interface touch controller TM4012E: 12.1” LCD Monitor w/ extra durable touch panel and PS/2 interface touch controller TM4015E: 15” LCD Monitor w/ extra durable touc h panel and PS/2 interface touch controller III. 1. 2. User’s Manual 3. 4. VGA cable: CCBLA-366 5. PS/2 KB cable w/ purple connectors: CCBLA-367 6. PS/2 Mouse cable w/ green connectors: CCBLA-384 7. USB cable: CCBLA-383 (for optional USB hub) 8. Posiflex Product Info
Summary of the content on the page No. 3
B. SIDE VIEWS Power on/off switch (Press on white dot to turn power on) Push in this direction to adjust the tilt angle C. REAR VIEW Lock/release button to detach the main unit Lock/release lever for tilt angle adjust Cable Exit V. INPUT / OUTPUT PORT a. DC 12V e. USB 2 i. TO (PC) RS232 PORT (option) b. USB TO PC f. USB 1 j. KB g. MOUSE k. TO (PC) KB PORT d. USB 3 h. TO (PC) MOUSE PORT l. MSR (option) e j g h i k a b c d f l 3 c. CRT of the display panel Lock/release lever Latch hole for cable c
Summary of the content on the page No. 4
VI. OPTION ITEMS 1. Wall Mount Kit 2. 3. RS232 interface touch controller for TM4012E or TM4015E only. (PS/2 interface controller will be hereby deleted for this option) 4. USB hub (1 up 3 down) VII. LL INS 1. For best cable routing effect, please do next step to place all required cables 2. Press down the lock/release button on stand assembly when lifting the main unit to separate main unit from the stand. Route all cables to be connected to PC or other device through the cable exit in stand a
Summary of the content on the page No. 5
4. Cable connection guide: CCBLA-366 VGA port of PC CCBLA-367 TO (PC) KB PORT PS/2 keyboard port of PC CCBLA-383 USB TO PC USB port of PC CCBLA-384 PS/2 mouse port of PC PS/2 keyboard MOUSE PS/2 mouse USB 1 ~ USB 3 Cable from power adaptor DC 12V Power adaptor Among these, power adaptor, CCBLA-366 and CCBLA-384 are crucial vital connections for functionality of TM4000 series. 5. Consolidate the cables and close and lock the cable cover. 6. 7. Adjust for best viewing tilt angle then proceed for
Summary of the content on the page No. 6
IX. LED INDIC • • Green: power on X. OSD “+” : to increase setting. “-” : to decrease setting. : to go to next option function. : to enter OSD setting menu or submenu, or to execute designated operation shown in operation shown in operation guide area. OSD description as below: Option Option function selected function list Exit Operation guide area Press “OSD” button on front bezel below the LCD panel when any normal screen is displayed to activate the OSD functions (on screen display adjustm
Summary of the content on the page No. 7
At this screen, pressing “+” button will increase screen contrast, pressing “-” button will decrease screen contrast and pressing “NEXT” button will change the selected option function to “Auto When the option function selected comes Exit to “Auto Adjust”, the operation guide area will indicate “Press OSD button to Auto Adjust” as drawing at right. After OSD button pressed, “Auto adjusting, please wait” will show up in operation guide area till operation completed. Pressing “NEXT” button will
Summary of the content on the page No. 8
4. If there is no touch function, please check the connection of the PS/2 Mouse cable with green connectors (CCBLA-384) or the RS232 cable (CCBLA- 368) for optional RS232 interface touch controller. Please pay particular attention on whether the PS/2 Mouse cable is connected to the right connector on TM4000 series or whether the RS232 cable is connected to the right COM port of PC according to the driver installation. 5. The USB hub function could be disrupted if any current overload of the down
