Summary of the content on the page No. 1
PT1700MX / PT1701MX /
PT1705MU
Touch Screen LCD Monitors
USER’S GUIDE
www.planar.com
Summary of the content on the page No. 2
Important Recycle Instructions: Lamp(s) inside this product contains mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG.
Summary of the content on the page No. 3
1 Table of Contents Usage Notice ........................................................................... 3 Precautions .....................................................................................................3 Introduction ............................................................................. 4 About Planar’s PT1700MX / PT1701MX / PT1705MU ...................................4 Touch Screen for PT1700MX...............................................................
Summary of the content on the page No. 4
2 Compatibility Modes......................................................................................21 Touch Screen Driver Installation ...................................................................22 Product Registration and Technical Support.................................................27
Summary of the content on the page No. 5
3 Usage Notice Warning- To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Warning- Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: Turn off the product before cleaning. Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glas
Summary of the content on the page No. 6
4 Introduction About Planar’s PT1700MX / PT1701MX / PT1705MU The PT1700MX / PT1701MX / PT1705MU is a 17” flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD). Features include: Direct Analog signal input Active matrix TFT LCD technology 1280x1024 SXGA resolution 17” viewable display area 31.5 ~ 80 kHz horizontal scan 56.3 ~ 75 Hz high refresh rate 0.264mm x 0.264mm Pixel pitch Auto adjustment function Multilingual
Summary of the content on the page No. 7
5 Touch Screen for PT1700MX 5-wire resistive touch screen for finger and stylus input Surface: Anti-glare treatment Interface: Dual RS-232 Serial/USB controller Durability: 35 million touches at a single point Hardness of surface: 3H Typical Operating force: 40g~200g when using a silicon rubber tipped pen with a 1 mm diameter minimum and a hardness of 60 degree. Transmittance: 82%±5% ® Driver: Windows VISTA, XP, 2000, ME, 98, CE, XP Embedded, Linux, ® Apple Mac OS
Summary of the content on the page No. 8
6 Durability: 30 million touches at a single point Hardness of surface: Mohs’ Hardness rating of 7 Operating force: 80g (min.) when using a soft-tipped stylus with an 8mm diameter minimum. Transmittance: 92%±5% Driver: Windows® VISTA, XP, 2000, 98
Summary of the content on the page No. 9
7 Package Overview LCD Display Power Cord VGA Signal Cable USB Cable - Type A to B Audio-in Cable RS-232 Cable (PT1700MX/PT1701MX) Landing Strip Touch Screen Driver User’s Guide Installation CD-ROM DC Power Supply (sold separately)
Summary of the content on the page No. 10
8 Installation Product Overview Front View PT1700MX/PT1701MX Bottom View (Without Stand) PT1705MU Bottom View (Without Stand)
Summary of the content on the page No. 11
9 Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products. The Kensington lock is not included.
Summary of the content on the page No. 12
10 VESA Mount your monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface Standard which defines a physical mounting interface for flat panel monitors, and corresponding standards for flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. To mount the monitor on a swing arm or other mounting fixture, follow the instructions included with the mounting fixture to be used.
Summary of the content on the page No. 13
11 Remove the Deskstand 1. Remove stand back cover. 2. Remove hinge cover 3. Remove 4 screws and then remove hinge.
Summary of the content on the page No. 14
12 Start Your Installation Remove the Back Cover Please follow these instructions to remove the cover on the back panel of the LCD so that you can hookup the cables to associated connector. Figure A. To remove the back cover, follow the arrows in Figure A and pull out with your fingers and the cover should be removed from the stand. Follow the instructions on page 14 ( Figure 11.1 ) to connect the cables to the appropriate connectors. Attach the cover back to the
Summary of the content on the page No. 15
13 Connecting the Display (Figure 11.1) To setup this display, please refer to the following figure and procedures. 1. Be sure all equipment is turned off. 2. Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet (11.1). 3. Connect the D-SUB cable from the display’s VGA input connector to the D-SUB connector of your host computer and tighten the screws (11.1). 4. Connect the Audio-In cable from the audio input port of your displ
Summary of the content on the page No. 16
14 Figure 11.1
Summary of the content on the page No. 17
15 User Controls Front Panel Controls / No Icon Menu No / Icon Control Function MENU Menu button Display the OSD menus 1. Increases the brightness of the display Brightness image. Plus/Plus 2. Increases value of the adjustment items. 1. Decreases the brightness of the display Brightness image. Minus/Minus 2. Decreases value of the adjustment items. Select – To select the adjustment items from Select OSD menus. Auto Auto – To ac
Summary of the content on the page No. 18
16 How to Use the OSD Menus 1. Press the "MENU" button to pop up the “on-screen menu” and to select among the four Main Menus. 2. Choose the adjustment items by pressing the “Select/Auto” button. 3. Adjust the value of the adjustment items by pressing the “”or “ “ button. 1. The OSD menu will automatically close, if you have left it idle for a pre-set time. 2. To disable the OSD menu buttons, please follow the instructions below: (Please note: the monitor has to be ON with a valid
Summary of the content on the page No. 19
17 On-Screen Display Menus Main OSD Menu: ITEM SUB MENU CONTENT Contrast 0-100 Adjusts the maximum luminance level of the monitor Brightness 0-100 Adjusts the backlight of the monitor Auto Adjust NO/YES Automatically adjusts the system clock The screen is moved horizontally right and left (1 pixel pitch Left/Right 0-100 increment) The screen is moved vertically up and down (1 line Down/Up 0-100 increment) Horizontal size 0-100 The ratio of dividing frequency of the dot clock is ad
Summary of the content on the page No. 20
18 Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. Check that all the I/O and power connectors are correctly and well connected as described in the “Installation” section. Make sure the pins of the connectors are not crooked or broken. Problem: Partial Image or incorrectly displayed image. Check to see if th
