Summary of the content on the page No. 1
PLANAR LCD MONITOR PE150 MANUAL www.planar.com
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Table of Contents Preface ...............................................................................................................................2 Chapter 1 Installation........................................................................................................4 Unpacking ............................................................................................................................................. 4 Connecting the LCD Monitor and Base .......................
Summary of the content on the page No. 4
Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form,
Summary of the content on the page No. 5
Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean LCD Monitor screen; -- Power off LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag. -- Gently clean the screen with dampened rag. 2. Do not place the LCD Monitor near a window. Exposing the monitor to rain water, moisture or sunlight can severely damage it. 3. Do not apply pressure to the LCD screen. Exces
Summary of the content on the page No. 6
Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. After you unpack the LCD Monitor, make sure that the following items were included in the box:
Summary of the content on the page No. 7
Detaching LCD Monitor from Its Stand 1. Unscrew screws of the hinge bracket 2. Remove the stand from LCD monitor (See fig. 1-3) Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig.1-3. The rear of this LCD display has four integrated 4 mm, 0.7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interfac
Summary of the content on the page No. 8
Power Management System This LCD Monitor complies with the VESA DPMS (version 1.0) Power Management guidelines. The VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync. signal. When the LCD Monitor is in power saving mode, the monitor screen will be blank and the power LED indicator will light yellow. Chapter 2 Display Controls User Controls A brief description and the location of all LCD Monitor function controls and indicators: Figure 2-1 1
Summary of the content on the page No. 9
Function Description Icon Function Function Description Brightness This function increases or decreases the brightness of the image. This function increases or decreases the difference between the dark and light Contrast color. H-Position This function shifts the entire display image left or right. V-Position This function shifts the entire display image up or down. A total of 32 scales (0 to 31) are available to adjust the focus and clarity of the Phase display. This functi
Summary of the content on the page No. 10
Chapter 3 Technical Information Specifications LCD Panel Size 15.0" (38 cm) Display Type Active matrix color TFT LCD Resolution 1024 x 768 Display Area (mm) 304 x 228 (H x V) 2 Brightness 200 cd/m (typical) Contrast Ratio 400:1 (typical) Response Time 35 ms (typical) Viewing Angle Vertical: -55° ~ +45° Horizontal: -65° ~ +65° Display Colors 16.7M with FRC or Dithering Video Input Signal Analog RGB 0.7Vp-p Input Impedance 75 Ohm ± 2% Polarity Positive, Negativ
Summary of the content on the page No. 11
Sync Input Signal Separate TTL compatible horizontal and vertical synchronization Polarity Positive and negative Supports VESA DDC1 and DDC2B functions Power Input (AC input) AC socket Video Cable 1.5M with 15-pin D-sub connector Operating Condition: Temperature 5°C to 40°C/41°F to 104°F Relative Humidity 20% to 80% Storage Condition: Temperature -20°C to 60° C/-4°F to140° F Relative Humidity 5% to 85% Input Voltage Single phase, 100 ~ 240VAC, 50 / 60 Hz Input Current 1.5 A maximum Dim
Summary of the content on the page No. 12
Troubleshooting This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected. Attention This LCD Monitor Supports Multiple VGA Modes. Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor. PROBLEM Picture is unclear and unstable The picture is unc
Summary of the content on the page No. 13
"
F Customer Service Online Support: http://planar.custhelp.com E-mail: desktopmonitors@planar.com Tel: 1-866-PLANAR-1 (1-866-752-6271) Hours: M-F, 8am - 9pm Eastern Time © 2003 Planar Systems, Inc. 05/03 Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.
