Summary of the content on the page No. 1
PL1900
Summary of the content on the page No. 2
1195 NW Compton Drive Beaverton, OR 97006-1992 www.planar.com Customer Service Planar provides the following technical support services: Internet Support For support available 24/7 visit Planar's Online Technical Support at www.planar.com/support. Our Online Technical Support is where you'll find solutions to many common problems, download documentation, view answers to frequently asked questions (FAQs) and get troubleshooting advice, or email Planar your support question. Talk to a
Summary of the content on the page No. 3
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is a registered trademark of Microsoft Inc. Other brand or prod
Summary of the content on the page No. 4
TABLE OF CONTENTS For Your Safety For Your Safety ---------------------------------------------------------------5 General Notes Special notes on LCD monitors ------------------------------------------7 Before You Operate The Monitor Features -----------------------------------------------------------------------8 Checking the contents of the package -------------------------------- 8 Installation Instructions Power source ------------------------------------------------
Summary of the content on the page No. 5
For Your Safety Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thi
Summary of the content on the page No. 6
PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit
Summary of the content on the page No. 7
GENERAL NOTES SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may i
Summary of the content on the page No. 8
BEFORE YOU OPERATE THE MONITOR FEATURES • 48.0cm(19”) TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions: 1280 X 1024 @60Hz ® • EPA ENERGY STAR • Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: Monitor Base Landing Strip User Manual 15-pin D-Sub Power Cord Adapter Cable Register Your Planar Products Today Thank you for choosing Planar
Summary of the content on the page No. 9
Installation Instructions Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3. Connect the AC-power cord into your LCD monitor’s External Adapter input socket, and then plug the other end of External adapter to LCD monitor’s DC-power-input. The AC-power cord may be connected
Summary of the content on the page No. 10
Installation Instructions CABLE CONNECTIONS Connecting the Signal Cable: the LCD monitor comes with a built-in signal cable. Plug the signal cable ′s 15-pin connector into the computer's VGA port and tighten the two screws on the cable connector. Connecting the Power Cord: Plug the AC-power cord into the External Adapter. Then plug the DC-jack power cable into DC-IN Inlet. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adap
Summary of the content on the page No. 11
Installation Instructions ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You are able to adjust the monitor’s angle from -5 ° to 20 °. Figure 2 NOTES • Do not touch the LCD screen when you change the angle. It may cause damage or break th
Summary of the content on the page No. 12
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the video cable from the monitor to the video card. • Press the power button to turn on the monitor position. The power indicator will light up.
Summary of the content on the page No. 13
OPERATING INSTRUCTIONS(cont.) • Power Button: Press this button to switch ON/OFF of monitor’s power. • MENU / ENTER : Active OSD menu or function adjust confirm or Exit OSD menu when in Brightness/Contrast OSD status. • Contrast : Adjust contrast or function adjust. • Brightness : Adjust brightness or function adjust. • Auto Adjust button / Exit: 1. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). 2. When OSD menu is in off status, pres
Summary of the content on the page No. 14
OPERATING INSTRUCTIONS (cont.) HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window (Figure 4). 2. Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press or again to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. 3. Press or to change the settings of the selecte
Summary of the content on the page No. 15
OPERATING INSTRUCTIONS (cont.) ADJUSTING THE PICTURE The descriptions for function control LEDS Main Sub Sub Main Menu Menu Menu Menu Description Item Icon Item Icon Contrast Contrast from Digital-register. Luminance Brightness Backlight Adjustment Adjust Picture Phase to reduce Focus Horizontal-Line noise Image Setup Adjust picture Clock to reduce Clock Vertical-Line noise. H. Adjust the horizontal position of Position the picture. Image Position V. Adjust th
Summary of the content on the page No. 16
OPERATING INSTRUCTIONS (cont.) Main Sub Main Sub Menu Menu Menu Description Menu Item Item Icon Icon H. Adjust the horizontal position of Position the OSD. OSD Adjust the vertical position of the V. Position Setup OSD. OSD Adjust the OSD timeout. Timeout Language Language N/A Select the language you like. Show the resolution, H/V Information Information N/A frequency and input port of current input timing. Clear each old status of Auto- Yes N/A configuration. Reset
Summary of the content on the page No. 17
PLUG AND PLAY Plug & Play DDC 2B Feature This monitor is equipped with VESA DDC 2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC 2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC 2B channel. THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL
Summary of the content on the page No. 18
TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Power Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent. Picture is fuzzy *Adjust the Contrast and Brightness Controls. Picture bounces or a wave *Move electrical devices that may pattern is present in the c
Summary of the content on the page No. 19
TECHNICAL SUPPORT (FAQ) (cont.) CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances in light picture. For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-down mode pattern. ERROR MESSAGE & POSSIB
Summary of the content on the page No. 20
APPENDIX SPECIFICATIONS Driving TFT Color LCD system LCD Panel Size 48.0cm(19") Pixel pitch 0.294mm( H ) × 0.294mm( V ) Video R,G,B Analog Interface Input Separate H/V TTL Sync. H-Frequency 30kHz – 83kHz (Analog) V-Frequency 55-75Hz (Analog) Display Colors 16.2M Colors Dot Clock 135MHz (Analog) Max. Resolution 1280 × 1024 @75Hz(Analog) TM Plug & Play VESA DDC2B EPA ENERGY ON Mode ≤37W ® STAR OFF Mode ≤2W Input Connector 15-pin D-Sub Input
