Summary of the content on the page No. 1
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Contents Contents ..............................................................................................................1 Preface ................................................................................................................2 Installation ...........................................................................................................4 Unpacking ..........................................................................................................
Summary of the content on the page No. 4
Preface This manual is designed to assist users in setting up and using the Integrated Thin Client Network Display (Network Display). Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechani
Summary of the content on the page No. 5
Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean the Network Display screen; -- Power off the Network Display and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a soft cloth. -- Gently clean the screen with dampened cloth. 2. Do not place the Network Display near a window. Exposing the display to rain water, moisture or sunlight can severely damage it. 3. Do not appl
Summary of the content on the page No. 6
Installation Unpacking Before unpacking the Network Display, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that Network Display has enough space around it for sufficient airflow. Though the Network Display uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. After you unpack the Network Display, make sure that the following items were included in th
Summary of the content on the page No. 7
Alternate Mounting Solutions Detaching Network Display from Its Stand Unscrew screws the swivel base support column and pull down the hinge to release. Figure 1-3 Interface for Arm/ Wall Mount Applications Before installing to mounting device, please refer to Fig.1-3. The rear of this LCD display has four integrated 4 mm, 0.7 pitch threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat
Summary of the content on the page No. 8
Connecting User Devices 1. USB devices such as the Keyboard can be connected to ports on the side or bottom (See Fig. 1-6 and Figure 1-7) 2. The unit may be secured through the use of Kensington locking devices. (See Figure 1-6) 3. The Headset/Handset port (RJ22) is reserved for future use with VOIP software support tools. It is designed for connection to analog telephone headsets or handsets. We recommend only the use of a UL or other safety agency approved device. Caution: This
Summary of the content on the page No. 9
Display Controls User Controls A brief description and the location of all Network Display functions controls and indicators: 54 32 1 Figure 2-1 Power Control - LED 1 Modes are changed by pressing the Power Control Button (Please refer to Figure 2-2) Brightness Function / Adjust increase 2 Brightness Function / Adjust decrease 3 Audio Volume Function / Adjust increase 4 Audio Volume Function / Adjust decrease 5 7
Summary of the content on the page No. 10
Power Modes The Network Display has three modes of operation. Figure 2-2 The following assumes the AC Power Adapter is connected to the display and an AC power source. Power Mode LED Operation Description • Power button is pressed for 3 Sec while in Standby mode (Thin client is switched off) • Power button is pressed for 3 Sec while in Run mode (Thin client Off Dark and display are switched off) 1 Caution: Be very careful to not turn off the Display while the operating sys
Summary of the content on the page No. 11
Technical Information Specifications LCD Panel ND1750 ND1950 Size 17" SXGA 19” SXGA Display Type Active matrix color TFT LCD Active matrix color TFT LCD Resolution 1280 x 1024 1280 x 1024 Display Dot 1280 x (RGB) x 1024 1280 x (RGB) x 1024 5:4 Aspect Ratio 5:4 Display Area , mm (H x V) 337.92 mm (H) x 270.34 mm (V) 376.32 mm (H) x 301.6 mm (V) Displayed Colors Up to16.2M with FRC or Dithering Up to 16.2M with FRC or Dithering 2 2 Brightness 300 cd/m (typical) 300 cd/m (typical Co
Summary of the content on the page No. 12
External Connections Power Input (DC input) DC Socket, 12V, 5A (Center Positive) GigaBit Ethernet port RJ45 USB ports 4 x USB connectors, Type A Receptacles Headphone 3.5mm Stereo Jack Microphone 3.5mm Mono Jack, Pink Headset RJ22 (4P4C, Reserved for Future VOIP Software Support) Environment Operating Condition: Temperature 5°C to 40°C/41°F to 104°F 20% to 80% Relative Humidity -20°C to 60° C/-4°F to140° F Storage Condition: Temperature 5% to 85% Relative Humidity Power Supply (AC I
Summary of the content on the page No. 13
Troubleshooting This Network Display has been pre-adjusted using factory standards. PROBLEM There is no image on Network Display If there’s no image on the Network Display, please perform the following steps: 1. Verify that the power cord is connected to a proper source of power. 2. Verify that the power cord is fully connected to the Power Adapter and that the Power Adapter cord is fully connected to the DC connector on the rear of the Display. The LED on the Power Adapter shou
Summary of the content on the page No. 14
End User License Agreement (“License”) IMPORTANT – READ CAREFULLY. THIS LICENSE IS A LEGAL DOCUMENT setting forth the terms under which Planar Systems, Inc. (“Licensor”) and its licensors and suppliers (collectively referred to as “Third Party Suppliers”) are willing to license to you software which is owned by Licensor and/or its Third Party Suppliers, who are intended third party beneficiaries under this License. Acceptance. Licensor is willing to license to you the enclosed softwa
Summary of the content on the page No. 15
Software. You may not decompile, reverse engineer or otherwise decode or alter the Software, or attempt to do any of the same, except and only to the extent that applicable law notwithstanding this limitation expressly permits such activity. Software Transfer. You may permanently transfer to another party ownership of the Device and equipment, including all of your rights under this License to use the Software, provided you retain no copies, you transfer the entire product (including th
Summary of the content on the page No. 16
