Summary of the content on the page No. 1
OWNER'S MANUAL
93CM CORDLESS REMOTE LCD TV/MONITOR
MODEL: TFTV930
N111
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
Summary of the content on the page No. 2
Table of Contents Important Safety Precautions ................................................................................. 1 Remote Control ...................................................................................................... 4 Identification of Controls ......................................................................................... 7 Connections ........................................................................................................... 9 Basic Op
Summary of the content on the page No. 3
Important Safety Precautions Electrical energy can perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the se
Summary of the content on the page No. 4
Important Safety Precautions (continued) 12. Stand --- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. Do not place the product on an unstable trolley, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. When mounting the product on a wall, be sure to follow the manufacturer's instructions. Use only the mounting ha
Summary of the content on the page No. 5
Important Safety Precautions (continued) 22. Power source --- This product is intended to be supplied by a listed power supply indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the
Summary of the content on the page No. 6
Remote Control Remote Control POWER 1. Turn the unit on or off Auto 2. To adjust picture automatically in VGA mode 1 9 PBP 3. 2 To activate picture-by-picture 10 11 3 P.S. 4. 4 12 To select signal source for PIP frame 5 13 6 PIP 5. 7 14 To activate picture-in-picture POS 6. 8 To adjust PIP frame position Menu 7. To access the Menu main page or exit menu operation CH+/- 8. Used to switch channels; in menu operation, use CH+/- to select menu item VOL+/- Used to adjust volume : in menu operation,
Summary of the content on the page No. 7
Remote Control (continued) Remote Control 15. Source To access source select menu 16. S-SYS Sound system select 17. C-SYS Colour system select 18. S. Mode Sound mode select 19. P. Mode Picture mode select 20. 0-9 number buttons Direct channel select 15 21 21. Mute Sound mute 22 16 22. NICAM 17 23 To select sound multiplex mode 18 24 19 25 23. SRS To turn on or off the SRS sound effect* 24. Headphone To output sound from headphone 20 26 25. Speaker To output sound from speaker 27 26. To quickly j
Summary of the content on the page No. 8
Remote Control (continued) Using the Remote Control Use the remote control by pointing it towards the remote sensor window of the set. Objects between the remote control and sensor window may prevent proper operation. Note: the illustration is for your reference only, the remote sensor may locate differently with different model. Cautions regarding use of remote control Do not expose the remote control to shock. In addition, do not expose the remote control to liquids, and do not place in an are
Summary of the content on the page No. 9
Identification of Controls Main Unit Front view Bottom view Power Indicator A blue indicator lights when the power Headphone jack Power Switch is on and a red indicator lights when in the standby mode. Remote Sensor 1 2 3 4 5 1. SOURCE To access signal source select menu. 2. Menu Press this button to access the Menu main page. 3. CH+/-: menu navigation buttons In OSD Menu, press these buttons to choose the OSD items. 4. VOL+/- Press the VOL+ or VOL- button to directly increase or decrease the s
Summary of the content on the page No. 10
Identification of Controls (continued) Main Unit Push downward and then pull out the cover carefully in the direction of the arrow to remove the cover. Push downward and then Back view pull out the cover carefully in the direction of the arrow to remove the cover. After all connections are made, aim the Insertion tabs toward the Locating grooves, then carefully push the Cover until it locks in place with a click. Side view Bottom view AUDIO AUDIO 3 4 5 1 2 1. AV outputs (Video, Audio L/mono, R
Summary of the content on the page No. 11
Connections Antenna Connection Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area. Note: It is recommended that the 75-ohm coaxial cable be used to eliminate interference and noise which may occur due to radio wave conditions. The aerial cable should not be bundled with the power cord and the like. 9
Summary of the content on the page No. 12
Connections (continued) Cautions Before Connecting Carefully check the terminals for position and type before making any connections. The illustration of the external equipment may be different depending on your model. Loose connectors can result in image or colour problems. Make sure that all connectors are securely inserted into their terminals. Refer to the operating manual of the external device as well. When connecting an external device, turn the power off on the panel to avoid any issues.
Summary of the content on the page No. 13
Connections (continued) Connect a Camcorder AUDIO AUDIO Bottom view Video cable Audio cable AV OUT S-VIDEO IN /AV1 INPUT /AV2 INPUT Y Yellow (VIDEO) W White (AUDIO L) R Red (AUDIO R) Camcorder, etc. How to connect: Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and camcorder. To playback Camcorder 1. Turn on your LCD TV , press Source button on the remote control. 2. Press CH+ or CH- to select Video2 and press Enter to confirm. Source Select 3. Turn on your camcor
Summary of the content on the page No. 14
Connections (continued) Connect a DVD Player (or Set-Top Box) Y Pb Pr AUDIO R AUDIO L Video Audio cable cable White (audio L) Side view Red (audio R, Pr/Cr) Green (Y) Video Blue (Pb/Cb) cable Audio cable DVD player, Set-top Box etc. How to connect a DVD Player (or Set-Top Box) using Component Video Connections: Connect the Video cable between the Y, Pb, Pr input jacks on the unit and Pb, Pr output jacks on the DVD player (or Set-Top Box). Connect the Audio cable between the AUDIO input jacks on
Summary of the content on the page No. 15
Connections (continued) Connect a DTV receiver Side view D-Sub AUDIO DVI DVI-D cable Audio AUDIO cable DTV receiver, etc. How to connect: 1. Connect the cable or antenna to the antenna input jack on the DTV receiver. 2. Connect the DVI cable between the DVI input interface on the unit and DVI Source Select output interface on the DTV receiver. VGA 3. Connect the Audio cable between the AUDIO input jack on the unit and AUDIO DVI output jacks on the DTV receiver. RF Video1 Video2 To Watch DTV YPbP
Summary of the content on the page No. 16
Connections (continued) Connect a PC Side view D-Sub AUDIO VGA Audio DVI-D cable cable AUDIO Computer or other equipment with VGA interface How to connect: Connect a VGA cable between the VGA jack on the PC and the D-Sub VGA input jack on the unit. Connect an Audio cable between the AUDIO output on the PC and AUDIO input jack on the unit. To Watch the PC screen Source Select 1. Turn on your LCD TV, press Source button on the remote control. VGA DVI 2. Press CH+ or CH- to select VGA. RF 3. Press
Summary of the content on the page No. 17
Connections (continued) To connect AV output terminal AUDIO AUDIO Bottom view AUDIO AUDIO Video Audio Y Yellow (VIDEO) cable cable W White (AUDIO L) R Red (AUDIO R) VCR for recording Audio amplifier How to connect: Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and VCR. Or connect the Audio cable between the Audio (L/R) jacks on the unit and Audio amplifier. How to record program 1. Turn on your LCD TV select a program you wish to record. 2. Turn on your VCR, ins
Summary of the content on the page No. 18
Basic Operations Turning the Unit On and Off Turning On Insert the power cord into the wall outlet. Press the Power Switch on the TV set, the set is in standby mode. Press the Power button on the remote control. The unit will be turned on and you will be ready to use it's features. Turning Off With the power on, press the Power button on the remote control to turn off the TV set temporarily. If you want to cut off the power completely, press the Power Switch on the TV set. Note: You can
Summary of the content on the page No. 19
Tuning In Auto Search Press Menu to display the menu main page. 1 Channel No. Add/Erase Press CH+ or CH- repeatedly to select CH item. Auto Search 2 Manual Search Fine Tune Sound System Color System Press Enter to access the submenu. 3 Channel Swap AFC Press CH- repeatedly to highlight Auto Search item. 4 Press Enter to store channels in memory automatically. 5 The unit will begin memorising all the available channels. During the process of the Auto Search, you can press Menu to exit. Manual Sea
Summary of the content on the page No. 20
Tuning In (continued) AFC (Auto Frequency Control) Press Menu to display the menu main page. 1 Channel No. Add/Erase Press CH+ or CH- repeatedly to select CH item. 2 Auto Search Manual Search Fine Tune Sound System Color System Press Enter to access the submenu. 3 Channel Swap AFC On Press CH+ or CH- repeatedly to select AFC item. 4 Press Enter to toggle On or Off. 5 When the AFC is set to On, the unit will automatically tune the program frequency to provide the best picture and sound. Fine-tune
