Summary of the content on the page No. 1
Q22wb
LCD Display
-User Guide
- Guide de l'utilisateur
- Bedienungsanleitung
- Guida dell'utente
-Pyководство по льз о в а теля
- Gebruikshandleiding
Model No. : VS11725
Summary of the content on the page No. 2
Contents TCO Information.......................................................................................... i Compliance Information.............................................................................. 1 Important Safety Instructions...................................................................... 2 Declaration of RoHS Compliance............................................................... 3 Copyright Information ............................................................
Summary of the content on the page No. 3
TCO Information Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO’03 Display requirements: Ergonomics Good visual ergonomics and image quali
Summary of the content on the page No. 4
Compliance Information For U.S.A. This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec
Summary of the content on the page No. 5
Important Safety Instructions 1. Read these instructions completely before using the equipment. 2. Keep these instructions in a safe place. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this equipment near water. Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 6. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the Display” in this guide for further instructions. 7. Do not block any ventilati
Summary of the content on the page No. 6
Declaration of RoHS Compliance This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.1% M
Summary of the content on the page No. 7
Copyright Information ® Copyright © ViewSonic Corporation, 2006. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Asso
Summary of the content on the page No. 8
Getting Started ® Congratulations on your purchase of a ViewSonic LCD display. Important! Save the original box and all packing material for future shipping needs. NOTE: The word “Windows” in this user guide refers to the following Microsoft operating systems: Windows ‘95, Windows NT, Windows ‘98, Windows 2000, Windows Me (Millennium), and Windows XP. Package Contents Your LCD display package includes: •LCD display • Power cord • Video cable • ViewSonic Wizard CD-ROM • Quick Start Guide NOTE: Th
Summary of the content on the page No. 9
Quick Installation 1. Connect power cord (and AC/DC • Wait for the CD-ROM to auto-start. adapter if required) NOTE: If the CD-ROM does not auto- start: double-click on the CD-ROM icon in 2. Connect video cable the Windows Explorer, then double-click • Make sure both the LCD display and on viewsonic.exe. computer are turned OFF • Follow the on-screen instructions. • Remove rear panel covers if necessary 5. Windows users: Set the timing mode • Connect the video cable from the LCD (resolution and
Summary of the content on the page No. 10
HOW TO USE THE STAND The monitor is shipped with the stand detached. Be sure to attach the stand before operating the display and remove if it is necessary to re-box. Install the Stand on a stable surface. The monitor may cause injury or damage if it falls CAUTION or is dropped. Do not give a strong impact to the monitor. It may cause damage. Unplug the monitor before installation to avoid electric shock or damage. 1. Put a piece of soft cloth on the table beforehand
Summary of the content on the page No. 11
Wall Mounting (Optional) ® To obtain a wall-mounting kit, contact ViewSonic or your local dealer. Refer to the instructions that come with the base mounting kit. To convert your LCD display from a desk- mounted to a wall-mounted display, do the following: 1. Verify that the Power button is turned Off, then Screw holes disconnect the power cord. 2. Lay the LCD display face down on a towel or blanket. 3. Remove the 2 screws attaching the base. 4. Remove the Plastic Covers from the back of the
Summary of the content on the page No. 12
Using the LCD Display Setting the Timing Mode Setting the timing mode is important for maximizing the quality of the screen image and minimizing eye strain. The timing mode consists of the resolution (example 1680 x 1050) and refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the OSD (On-screen Display) controls to adjust the screen image. For the best picture quality set your LCD display timing mode to: VESA 1680 x 1050 @ 60Hz. To set the Timing Mode: 1. Set
Summary of the content on the page No. 13
CONTROLS AND CONNECTORS A U T O EXIT ENTER 1 Auto Button (AUTO) 2 Exit / Volume Button (EXIT) 3 Scroll Down / Contrast Button ( ) 4 Scroll Up / Brightness Button ( ) 5 Menu / Select Button (ENTER) 6 Power Switch ( ) 7 Power Indicator NOTE Green: Normal operation Orange: Power Management T he monitor enters into power management mode which reduces the power consumption to less than 2W when
Summary of the content on the page No. 14
OPERATING THE MONITOR Press the ENTER Button to start the On Screen Display feature. There are additional Menu 1 items which can be switched by using the / Buttons. Main Menu Auto Adjust Language Luminance Recall Geometry Miscellaneous Color Input Select OSD Select the Menu item which contains the adjustment icon relating to the adjustment you want to 2 make. Press the ENTER Button. Then, use the / Buttons to highlight the desired adjustment icon. 3 Press the ENTER Button again. Use
Summary of the content on the page No. 15
ADJUSTMENT MENU CONTENTS Auto Adjust Only Analog Input Adjustment Item Problem / Option Button to Press Adjust H. / V. Position, Pixel Clock and Phase Auto Adjust * Direct automatically. * For best results, use the Auto Adjust in conjunction with the adjustment pattern. Direct You can skip the Menu items and display an adjustment scale directly by using the following button operations. Auto Adjust: Press the Auto Button when the Menu is not displayed. Luminance Adjust
Summary of the content on the page No. 16
Geometry Only Analog Input Adjustment Item Problem / Option Button to Press Too left H. Position Too right Too low V. Position Too high Too narrow Pixel Clock Too wide Phase To correct flickering text or lines Color Adjustment Item Problem / Option Button to Press 9300K Bluish white 7500K Yellowish white 6500K Reddish white Red Too weak User Preset Green Too strong Blue OSD Adjustment Item Problem / Option
Summary of the content on the page No. 17
Language Adjustment Item Problem / Option Button to Press English English Español Spanish Français French Nederlands Dutch Language Deutsch German Japanese Italiano Italian 簡體中文 Simplified Chinese Traditional Chinese Russian 繁體中文 Русско Recall Adjustment Item Problem / Option Button to Press Factory-preset data is restored. Yes Recall All No Return to Menu. Miscellaneous Adjustment Item Problem / Option Bu
Summary of the content on the page No. 18
Input Select Adjustment Item Problem / Option Button to Press D-sub Select the Analog input. Input Select DVI Select the Digital input. NOTE When only one of the two signal inputs is connected to the signal source, the one connected NOTE is automatically selected. Input Select function is not available if there is no signal input from the selected connector or during the power management mode. Optiquest Q22wb
Summary of the content on the page No. 19
Other Information Specifications LCD Type 22” (22" wide viewable diagonal area), TFT (Thin Film Transistor), Active Matrix WSXGA+ LCD, 0.282 mm pixel pitch Color Filter RGB vertical stripe Glass Surface Anti-Glare Input Signal Video Sync RGB analog (0.7/1.0 Vp-p, 75 ohms) / TMDS Digital (100ohms) Separate Sync, f :31-81 kHz, f :55-76 Hz h v Compatibility PC Up to 1680 x 1050 Non-interlaced 1 Power Macintosh up to 1680 x 1050 Macintosh Resolution Recommended 1680 x 1050 @ 60 Hz and supported 1440
Summary of the content on the page No. 20
Troubleshooting No power • Make sure power button (or switch) is ON. • Make sure A/C power cord is securely connected to the LCD display. • Plug another electrical device (like a radio) into the power outlet to verify that the outlet is supplying proper voltage. Power is ON but no screen image • Make sure the video cable supplied with the LCD display is tightly secured to the video output port on the back of the computer. If the other end of the video cable is not attached permanently to the LCD
