Summary of the content on the page No. 1
V191W
V221W
User’s Manual
Summary of the content on the page No. 2
Index Warning, Caution .........................................................................................................................English-1 Registration Information ...............................................................................................................English-1 Contents.......................................................................................................................................English-3 Quick Start ...................................
Summary of the content on the page No. 3
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PL
Summary of the content on the page No. 4
Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1. Use the attached specified cables with the V191W/V221W color monitor so as not to interfere with radio and television reception. (1) The power supply cord you use must have been appro
Summary of the content on the page No. 5
Setup Manual Contents Your new NEC LCD monitor box* should contain the following: • LCD monitor with tilt base • Power Cord •Video Signal Cable • Setup Manual • CD-ROM (only EU) • Base Stand • Stand Neck CD-ROM Setup Manual Power Cord Video Signal Cable LCD monitor (Type of power cord included will (only EU) (Stand not connected) depend on the where the LCD monitor is to be shipped) * Remember to save your original box and packing material to transport or ship the monitor. Quick Start To attac
Summary of the content on the page No. 6
3. Connect one end of the power cord to the monitor and the other end to the power outlet (Figure B.1). NOTE: Please confirm that the tabs are completely secure. NOTE: Please refer to Caution section of this manual for proper selection of power cord. 4. Turn on the monitor with the front power button and the computer (Figure C.1). 18˚ Tilt Power Cord Power Button D-Sub Figure B.1 Figure C.1 5. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most
Summary of the content on the page No. 7
Removing the Base NOTE: Always remove the Base when shipping the LCD. 1. Place monitor face down on a non-abrasive surface (Figure R.1). 2. Insert the thin rod into the hole in the back of LCD monitor and using your thumbs, press the tabs on the back side of base stand in the direction of the arrows the pull out the stand as indicated (Figure R.1). Connecting a Flexible Arm This LCD monitor is designed for use with a flexible arm. Please use the screws (4pcs) as shown in the picture when install
Summary of the content on the page No. 8
Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: 1. Basic function at pressing each key Button At No OSD Shortcut to Bright adjust Shortcut to Contrast adjust “Auto adjust” operate. Showing OSD. showing window. window. At OSD showing Go to Adjustment stage. Cursor goes to left. Cursor goes to right. (Icon selection stage) At OSD showing Go to Icon selection stage. Adjust value decrease or Adjust value increase or Reset operation. (Adjustment stage
Summary of the content on the page No. 9
BRIGHTNESS Adjusts the overall image and background screen brightness. To enter the ECO MODE, press the “AUTO” button. CONTRAST Adjusts the image brightness in relation to the background. AUTO CONTRAST Adjusts the image displayed for non-standard video inputs. AUTO ADJUST Automatically adjusts the Image Position, the H. Size and Fine setting. LEFT/RIGHT Controls Horizontal Image Position within the display area of the LCD. DOWN/UP Controls Vertical Image Position within the display area of the L
Summary of the content on the page No. 10
OSD LOCK OUT This control completely locks out access to all OSD control functions without Brightness and Contrast. When attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the OSD are locked out. To activate the OSD Lock Out function, press “AUTO”, then “+” key and hold down simultaneously. To de-activate the OSD Lock Out, press “AUTO”, then “+” key and hold down simultaneously. RESOLUTION NOTIFIER If ON is selected, a message will appear on the scree
Summary of the content on the page No. 11
Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabinet slots, a
Summary of the content on the page No. 12
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes. The optimal distance is 50 cm. • Rest
Summary of the content on the page No. 13
Specifications - V191W Monitor Specifications V191W Monitor Notes LCD Module Diagonal: 47.01 cm/18.5 inches Active matrix; thin film transistor (TFT) Viewable Image Size: 47.01 cm/18.5 inches liquid crystal display (LCD); Native Resolution (Pixel Count): 1366 x 768 0.30 (H) mm x 0.30 (V) mm dot pitch; 2 280 cd/m (typ) white luminance, 1000:1 contrast ratio (typ), response time: 5 ms. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync.TTL Level (Positive/Negative) Display Colours Ana
Summary of the content on the page No. 14
Specifications - V221W Monitor Specifications V221W Monitor Notes LCD Module Diagonal: 54.79 cm/21.6 inches Active matrix; thin film transistor (TFT) Viewable Image Size: 54.79 cm/21.6 inches liquid crystal display (LCD); Native Resolution (Pixel Count): 1920 x 1080 0.248 (H) mm x 0.248 (V) mm dot pitch; 2 300 cd/m (typ) white luminance, 800:1 contrast ratio (typ), response time: 5 ms. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync.TTL Level (Positive/Negative) Display Colours A
Summary of the content on the page No. 15
Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The small footprint and low weight allow it to be moved or transported easily from one location to another. No-touch Auto Adjust: No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup. Plug and Play: The Microsoft solution with the Windows operating system facilitates setup and installation by allowing the monitor
Summary of the content on the page No. 16
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Check front power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and your display card with respect to compatibility and
Summary of the content on the page No. 17
TCO’03 Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO’03 Display requirements: Ergonomics • Good visual ergonomics and image quality in ord
Summary of the content on the page No. 18
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union). Disposin
