Summary of the content on the page No. 2
Index Warning 1 Contents 2 Quick Start 3-7 Controls 8-9 Recommended Use 10-11 Specifications 12 Features 13 Troubleshooting 14 References 15 Limited Warranty 16 TCO ’99 17-18 Avertissement 20 Contenu 21 Mise en marche rapide 22-26 Commandes 27-28 Usage recommandé 29-30 Fiche technique 31 Fonctions 32 Dépannage 33 Références 34 Garantie limitée 35 TCO ’99 36-37 78134761.wpc 2 9/16/99, 4:10 PM
Summary of the content on the page No. 3
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS IN
Summary of the content on the page No. 4
MultiSync LCD1525S Contents You can register your product online at www.nectech.com/productregistration ® Your new NEC Technologies MultiSync LCD monitor box* should contain the following: ™ • MultiSync LCD1525S monitor with tilt/swivel base • Power Cord (# 70810786) • AC Adapter (#A2425S01) (located in base) • Video Signal Cable • USB Cable • User’s Manual MultiSync LCD1525S monitor with Video Signal Cable Power Cord User’s Manual USB Cable * Remember to save your original box and packing mater
Summary of the content on the page No. 5
Quick Start ® To attach the MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC: Connect the 15-pin mini D-SUB of the appropriate signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. ™ For the Mac: Connect the MultiSync LCD1525S Macintosh cable adapter to the computer (Figure B.1). Attach the 15-pin mini D-SUB end of the appropriate signal cable to the MultiSync LCD1525S Macintosh cab
Summary of the content on the page No. 6
Quick Start cont. Macintosh Cable Adapter Figure A.1 Figure B.1 (not included) 1 2 Clip A 2 1 Figure C.1 4 78134761.wpc 6 9/16/99, 4:10 PM
Summary of the content on the page No. 7
MultiSync LCD1525S MultiSync Quick Start cont. A Type B Type Figure D.1 Figure E.1 Figure F.1 Figure G.1 5 78134761.wpc 7 9/16/99, 4:10 PM
Summary of the content on the page No. 8
Quick Start cont. Tilt Grasp both sides of the monitor screen with your hands and adjust the tilt as desired (Figure TS.1). Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Remove the back cover and the cable cover (Figure R.1). Figure TS.1 1 2 Figure R.1 2. Disconnect all cables. 3. Place monitor face down on a non-abrasive surface (Figure R.2). 4. Remove the 4 screws connecting the monitor to the stand and lift off the stand assembly (Figure R.2). Th
Summary of the content on the page No. 9
Quick Start cont. Remove AC Adapter from Monitor Stand To remove the AC Adapter 1. Remove the back panel and remove cable cover (Figure AC.1). 2. Disconnect all cables. 3. Place monitor face down on a non-abrasive surface (Figure AC.2). 4. Remove the 4 screws on the bottom of the stand and lift bottom panel (Figure AC.3). Figure AC.1 5. Pull out the AC Adapter and cord (Figure AC.4). 6. Reattach the bottom panel to the stand. Tighten all screws. To connect the AC Adapter outside of the stand, pl
Summary of the content on the page No. 10
Controls INPUT SELECT If no OSM menu is displayed, video input and USB upstream can be changed by pressing the PROCEED button. : Changes only video : Changes video and USB ™ OSM (On-Screen-Manager) Controls To acess OSM press any of control buttons ( , , , ). The OSM controls on the front of the monitor function as follows: Control Main Menu Sub-Menu EXIT Exits the OSM controls. Exits to the OSM controls main menu. CONTROL / Moves the highlighted Moves the highlighted area area
Summary of the content on the page No. 11
Controls cont. ® AccuColor Control System Five color presets select the desired color setting. If a setting is adjusted, the name of the setting will change to Custom. Color Gain (Red, Green, Blue): Increases or decreases Red, Green or Blue color depending upon which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown by the color bars. Tools Language Select: OSM control menus are available in seven languages. ™ OSM Position: You can choo
Summary of the content on the page No. 12
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING ® THE MULTISYNC LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabin
Summary of the content on the page No. 13
Recommended Use cont. CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 16 inches and no further away than 28 inches from your eyes. The opt
Summary of the content on the page No. 14
Specifications ® ™ Monitor MultiSync LCD1525S Notes Specifications Monitor LCD Module Diagonal: 15.4 inch Active matrix; thin film transistor (TFT) Viewable Image Size: 15.4 inch liquid crystal display (LCD); 0.2385 mm dot 2 Native Resolution (Pixel Count): 1280 x 1024 pitch; 200cd/m white luminence; 200:1 contrast ratio, typical Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Composite Sync. (Positive
Summary of the content on the page No. 15
Features ™ NuCycle Plastic: A special silicone compound for PC resin, being extremely flame retardant, safe and environmentally friendly. Dual Inputs: Offers dual inputs, allowing you to connect the monitor to two systems. You can easily switch between computers with a touch of a button on the front control panel. USB Hubs: There are two USB Hubs, two upstream ports and four downstream ports. You can use two sets of computers with one monitor. Wider Compatibility: Because the MultiSync LCD monit
Summary of the content on the page No. 16
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and your display card with respect to compatibility and recommended
Summary of the content on the page No. 17
References • BBS (978) 742-8706 NEC Technologies’ Remote Bulletin Board System is an electronic service accessible with your system and a modem. Communication parameters are: 300/1200/2400/9600/14.4k/28.8k/33.6k bps, no parity, 8-data bits, 1 stop bit • Customer Service/ Technical Support (800) 632-4662 Fax (978) 635-7049 • Electronic Channels: Internet e-mail: tech-support@nectech.com Internet ftp site: ftp.nectech.com World Wide Web: http://www.nectech.com Product Registration: http://www.nect
Summary of the content on the page No. 18
Limited Warranty NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NECTECH’s sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase. Spare parts are warranted for ninety (90) days. Replacement parts or units may be new or refurbished and will meet specifications o
Summary of the content on the page No. 19
TCO’99 Congratulations! You have just purchased a TCO’99 approved and labeled product! Your choice has provided you with a product devel- oped for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encourag- ing the adaptation of goods and
Summary of the content on the page No. 20
TCO’99 cont. accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. TCO’99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound chlorine and bromine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead dama
Summary of the content on the page No. 1
NEC LCD Series
®
MultiSync
MultiSync
™
™
LCD1525S
LCD1525S
User’s Manual
User’s Manual
78134761.wpc 1 9/16/99, 4:10 PM
You can
register your
product online at
www.nectech.com/
productregistration
