Summary of the content on the page No. 1
1550M
Summary of the content on the page No. 2
Index Warning .................................................................................................................... 1 Contents ................................................................................................................. 2 Quick Start ............................................................................................................. 3 Controls .............................................................................................................
Summary of the content on the page No. 3
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PL
Summary of the content on the page No. 4
Contents ® Your new NEC MultiSync LCD monitor box* should contain the following: ™ • MultiSync LCD1550M monitor with tilt / swivel base • Power Cord • Video Signal Cable • Audio Cable • USB Cable • User’s Manual Power Cord Video Signal Cable USB Cable User’s Manual Audio Cable *Remember to save your original box and packing material to transport or ship the monitor. 2 1550M 1550M
Summary of the content on the page No. 5
Quick Start ® To attach the MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. Remove connector cover and cable cover. Connect the audio cable to “Line-in” on the back of the monitor and the other end to the “Audio out” terminal of the computer. Place the Audio cable under Clip B (Figure A.1). 3. For the PC: Connect the 15-pin mini D-SUB of the appropriate signal cable to the connector of the display card in your system (Figure B.1). Tigh
Summary of the content on the page No. 6
Quick Start –continued Clip B Figure A.1 Note: Some Macintosh systems do not require a Macintosh Cable Adapter Macintosh Cable Adapter (not included) Figure B.1 Figure C.1 Clip B Figure D.1 4
Summary of the content on the page No. 7
Quick Start –continued Figure E.1 A Type B Type Figure F.1/G.1 Vacation Switch Power Button Figure H.1 5 1550M
Summary of the content on the page No. 8
Quick Start –continued Tilt and swivel Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1). Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1.Remove the connector cover and the Figure TS.1 cable cover (Figure R.1). 2.Disconnect all cables. 3.Place monitor face down on a non-abrasive surface (Figure R.2). 4.Remove the 4 screws connecting the monitor to the stand and lift off the stand assembly (Fi
Summary of the content on the page No. 9
Quick Start –continued 7. This LCD monitor is designed for use with a flexible arm. Please use the attached screws (4pcs) as shown in the picture when installing. To meet the safety requirements, the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor. The LCD monitor shall only be used with an approved arm (e.g. GS mark). Replace screws. Tighten all screws. Specifications 4-SCREWS (MAX depth:10mm) Weight of LCD
Summary of the content on the page No. 10
Controls OSM™ (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM menu, press any of the control buttons ( , , –, +, NEXT ). Menu EXIT Exits the OSM controls. Exits to the OSM main menu. CONTROL / Moves the highlighted area left/right to select control menus. Moves the highlighted area up/down to select one of the controls. ADJUST –/+ Moves the bar left/right to increase or decrease the adjustment. Active Auto Adjust function. Enter the Sub Menu
Summary of the content on the page No. 11
Controls –continued ® AccuColor Control Systems ® AccuColor Control Systems: Six color presets select the desired color setting (sRGB and NATIVE color presets are standard and cannot be changed). Color temperature increases or decreases, in each preset. R,Y,G,C,B,M,S: Increases or decreases Red, Yellow, Green, Cyan, Blue, Magenta and Saturation depending upon which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown by the color bars. NAT
Summary of the content on the page No. 12
Controls –continued Information DISPLAY MODE: Indicates the current display resolution and frequency setting of the monitor. MONITOR INFO: Indicates the model and serial numbers of your monitor. ™ OSM Warning: OSM Warning menus disappear with Exit button. NO SIGNAL: This function gives a warning when there is no signal present. After power is turned on or when there is a change of input signal or video is inactive, the No Signal window will appear. RESOLUTION NOTIFIER: This function gives a warn
Summary of the content on the page No. 13
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING ® THE MULTISYNC LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabin
Summary of the content on the page No. 14
Recommended Use –continued CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 16 inches and no further away than 28 inches from your eyes. Th
Summary of the content on the page No. 15
Specifications ® ™ Monitor MultiSync LCD1550M Notes Specifications Monitor LCD Module Diagonal: 15.0 inch Active matrix; thin film transistor (TFT) Viewable Image Size: 15.0 inch liquid crystal display (LCD); 0.30 mm dot 2 Native Resolution (Pixel Count): 1024 x 768 pitch; 300cd/m white luminence; 450:1 contrast ratio, typical Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Display Colors Analog input
Summary of the content on the page No. 16
Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The monitor’s small footprint and low weight allow it to be moved or transported easily from one location to another. ® AccuColor Control Systems: Six color presets select the desired color setting (sRGB an NATIVE color presets are standard and cannot be changed). Color temperature increases or decreases, in each preset. R,Y,G,C,B,M,S: Increases or decre
Summary of the content on the page No. 17
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Check the Vacation Switch should be in the ON position. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and
Summary of the content on the page No. 18
Troubleshooting –continued Selected resolution is not displayed properly • Use OSM Display Mode to enter Information menu and confirm that the appropriate resolution has been selected. If not, select corresponding option. No Sound • Check to see if speaker cable is properly connected. • Check to see if mute is activated. • Check to see if volume in OSM is set at minimum. USB Hub does not operate • Check to make sure the USB cord is properly connected. Refer to your USB device User’s Manual. 16
Summary of the content on the page No. 19
References • BBS (978) 742-8706 NEC-Mitsubishi Electronics Display of America Remote Bulletin Board System is an electronic service accessible with your system and a modem. Communica- tion parameters are: 300/1200/2400/9600/14.4k/28.8k/33.6k bps, no parity, 8-data bits, 1 stop bit • Customer Service/ Technical Support (800) 632-4662 Fax (978) 742-7049 • Electronic Channels: Internet e-mail: tech-support@necmitsubishi.com Internet ftp site: ftp.necmitsubishi.com World Wide Web: http://www.necmits
Summary of the content on the page No. 20
Limited Warranty NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase. Spare parts are warranted for ninety (90) days. Replacement parts or unit may be new or refurbished and wil
