Summary of the content on the page No. 1
™
NEC AccuSync Series
AccuSync
AccuSync
50/70/90
50/70/90
User’s Manual
User’s Manual
15500371.wpc 1 9/30/99, 5:40 PM
You can
register your
product online at
www.nectech.com/
productregistration
Summary of the content on the page No. 2
Index Warning 1 Contents 2 Quick Start 3-6 Controls 7-8 Recommended Use 9-10 Specifications 11-13 Features 14 Troubleshooting 15 References 16 Limited Warranty 17 Avertissement 19 Contenu 20 Mise en marche rapide 21-24 Commandes 25-26 Usage recommandé 27-28 Fiche techniques 29-31 Fonctions 32 Dépannage 33 Références 34 Garantie limitée 35 15500371.wpc 2 9/30/99, 5:40 PM
Summary of the content on the page No. 3
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS IN
Summary of the content on the page No. 4
Contents You can register your product online at www.nectech.com/productregistration ™ Your new NEC Technologies AccuSync monitor box* should contain the following: • AccuSync Monitor with tilt/swivel base AccuSync 50, 70 or 90 • Power Cord • Captive Signal Cable • User’s Manual Captive Signal Cable Power Cord Tilt Swivel Base User’s Manual * Remember to save your original box and packing material to transport or ship the monitor. 2 15500371.wpc 4 9/30/99, 5:41 PM
Summary of the content on the page No. 5
Quick Start Attach Tilt/Swivel Base ™ To attach the AccuSync monitor to your system, follow these instructions: 1. With the monitor unplugged from your system and the wall outlet, carefully turn the monitor upside fown on a firm table (Figure TS-1). 2. Position the six hooks of the tilt/swivel base into the six holes on the bottom of the monitor (Figure TS.2). 3. Slide the tilt/swivel base forward until the latch of the tilt/swivel base is secure (Figure TS.3). 4. Having successfully installed y
Summary of the content on the page No. 6
Quick Start cont. Remove Tilt/Swivel Base To remove the tilt/swivel base from the AccuSync monitor, follow these instruction: 1. With the monitor unplugged from your system and the wall outlet, carefully turn the monitor upside down on a firm table (Figure TS-1). 2. Push down on the latch of the tilt/swivel base and slide the tilt/swivel base backward from the front of the monitor (Figure TS.5). 3. Pull out the tilt/swivel base from the six holes on the bottom of the monitor (Figure TS.6). front
Summary of the content on the page No. 7
Quick Start cont. ™ To attach the AccuSync monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. If necessary, install the display card into your system. For more information, refer to the display card manual. 3. For the PC: Connect the 15-pin mini D-SUB of the captive signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the Mac: Connect the Macintosh cable adapter (not included) to the monitor connector on
Summary of the content on the page No. 8
Quick Start cont. Mac Adapter (Not Included) 15-pin mini D-SUB Captive Signal Cable Figure B.1 Power Outlet Power Cord Figure C.1 Power Button Figure D.1 6 15500371.wpc 8 9/30/99, 5:41 PM
Summary of the content on the page No. 9
Controls ™ OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: SELECT Enters and exits the OSM menu. CONTROL –/+ Selects one of the controls and increases or decreases the adjustment. RESET Resets the highlighted control to the factory setting. Adjusts the overall image and background screen brightness. Adjusts the image brightness in relation to the background. Red Color Contrast: Adjust the red contrast of the display Green Color Contrast: Adjust the green
Summary of the content on the page No. 10
Controls cont. Increases or decreases the curvature of the sides either to the left or right. Rotates the entire display clockwise or counterclockwise. Degauss Control: Eliminates the buildup of stray magnetic fields that alter the correct scan of the electron beams and affect the purity of the screen colors, focus and convergence. When activated, your screen image will jump and waver a bit as the screen is demagnetized. Caution: Please allow a minimum of 20 minutes to elapse between uses of th
Summary of the content on the page No. 11
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING ™ THE AccuSync COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabinet sl
Summary of the content on the page No. 12
Recommended Use cont. CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 12 inches and no further away than 28 inches from your eyes. The optimal distance is 18 inches. • Rest your eyes periodically
Summary of the content on the page No. 13
Specifications ™ Monitor AccuSync 50 Notes Specifications Monitor Picture Tube Diagonal: 15 inch 90 deflection, 0.28 mm trio dot pitch, Viewable Image Size: 13.8 inch medium short persistence phosphor, Radius: 1080 mm multi-layered, anti-static screen coating, semi-tint screen, Invar Shadow Mask and ® OptiClear screen surface. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Display Colors Analog input
Summary of the content on the page No. 14
Specifications cont. ™ Monitor AccuSync 70 Notes Specifications Monitor Picture Tube Diagonal: 17 inch 90 deflection, 0.27 mm trio dot pitch, Viewable Image Size: 16.0 inch medium short persistence phosphor, Radius: 1210 mm multi-layered, anti-static screen coating, semi-tint screen, Invar Shadow Mask and ® OptiClear screen. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Display Colors Analog input:
Summary of the content on the page No. 15
Specifications cont. ™ Monitor AccuSync 90 Notes Specifications Monitor Picture Tube Diagonal: 19.0 inch 90 deflection, 0.26 mm trio dot pitch, Viewable Image Size: 18.0 inch medium short persistence phosphor, Radius: 1360 mm multi-layered, anti-static screen coating, semi-tint screen, Invar Shadow Mask and ® OptiClear screen surface. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Display Colors Anal
Summary of the content on the page No. 16
Features ® OptiClear Screen Surface: Reduces reflection and glare and increases contrast without sacrificing focus level, clarity or brightness. Along with the flat square technology CRT, a high contrast screen delivers crisp, clean text and graphics. Invar Shadow Mask: Holes in the thin metal sheet behind the glass of the CRT surface correspond to each phosphor dot on the inner surface of the CRT’s faceplate, allowing the correct electron beam (red, green, blue) to hit the correct color phospho
Summary of the content on the page No. 17
Troubleshooting No picture • Display card should be completely seated in its slot. • Power Button and computer power switch should be in the ON position. • Signal cable should be completely connected to display card/computer. • Check connector for bent or pushed-in pins. Image is scrolling or unstable • Signal cable should be completely attached to the computer. • Check pin assignments and signal timings of the monitor and your display card with respect to recommended timings and pin assignments
Summary of the content on the page No. 18
References • BBS (978) 742-8706 NEC Technologies’ Remote Bulletin Board System is an electronic service accessible with your system and a modem. Communication parameters are: 300/1200/2400/9600/14.4k/28.8k bps, no parity, 8-data bits, 1 stop bit • Customer Service/ Technical Support (800) 632-4662 Fax (978) 742-7049 • Electronic Channels: Internet e-mail: tech-support@nectech.com Internet ftp site: ftp.nectech.com World Wide Web: http://www.nectech.com Product Registration: http://www.nectec
Summary of the content on the page No. 19
Limited Warranty NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NECTECH’s sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase. Spare parts are warranted for ninety (90) days. Replacement parts or units may be new or refurbished and will meet specifications o
Summary of the content on the page No. 20
Notes 18 15500371.wpc 20 9/30/99, 5:41 PM
