Summary of the content on the page No. 1
USER'S MANUAL
®
MultiSync
™
FE750+
To learn about other special offers, register your product online at www.necmitsubishi.com/ productregistration
Fe750+.wpc 1 11/1/00, 10:45 AM
Summary of the content on the page No. 2
Index Warning.................................................................................................. 1 Contents ............................................................................................... 2 Quick Start ...........................................................................................3 Controls ................................................................................................ 5 Recommended Use ..................................................
Summary of the content on the page No. 3
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS IN
Summary of the content on the page No. 4
Contents ® ™ Your new NEC MultiSync FE750+ monitor box* should contain the following: • MultiSync FE750+ Monitor with tilt/swivel base • Power Cord • Captive Signal Cable • User’s Manual Captive Signal Cable USER'S MANUAL ® MultiSync ™ FE750+ To learn about other special offers, register your product online at www.necmitsubishi.com/ productregistration User’s Manual Power Cord * Remember to save your original box and packing material to transport or ship the monitor. 2 Fe750+.wpc 4 11/1/00, 10:
Summary of the content on the page No. 5
Quick Start ® ™ To attach the MultiSync FE750+ monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. If necessary, install the display card into your system. For more information, refer to the display card manual. 3. For the PC: Connect the 15-pin mini D-SUB of the captive signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the Mac: Connect the MultiSync FE750+ Macintosh cable adapter (not included) to the
Summary of the content on the page No. 6
Quick Start –continued Figure B.1 Figure C.1 Power Button – + EXIT PROCEED RESET Figure D.1 4 Fe750+.wpc 6 11/1/00, 10:45 AM
Summary of the content on the page No. 7
Controls ™ OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: Main Menu Sub-Menu EXIT Exits the OSM menu. Exits to the OSM controls main menu. CONTROL Moves the highlighted Moves the highlighted area / area up/down to select up/down to select one of the one of the controls. controls. CONTROL Moves the highlighted Moves the bar in the – or + –/+ area left/right to select direction to decrease or one of the controls. increase the adjustment. PROCEED Has no
Summary of the content on the page No. 8
Controls –continued ® Color Control/AccuColor Control System Color presets 1 through 5 selects the desired color setting. The bar is replaced by the color setting choice from 1 to 5. Each color setting is adjusted at the factory to the stated Kelvin. If a setting is adjusted, the name of the setting will change from Kelvin to Custom. Red, Green, Blue: AccuColor Control System decreases or increases the monitor's red, green or blue color guns depending upon which is selected. The change in co
Summary of the content on the page No. 9
Controls –continued save or return to the previous setting once you select a different control. If the save is not confirmed, the setting will go back to previous setting when OSM turns off. ™ Factory Preset: Selecting Factory Preset allows you a reset most OSM control settings back to the factory settings. A warning statement will appear to confirm that you do want to reset ALL settings. Individual settings can be reset by high- lighting the control to be reset and pressing the RESET button. T
Summary of the content on the page No. 10
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING ® ™ THE MULTISYNC FE750+ COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the
Summary of the content on the page No. 11
Recommended Use –continued CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 12 inches and no further away than 28 inches from your eyes. The optimal distance is 24 inches. • Rest your eyes periodi
Summary of the content on the page No. 12
Specifications ® ™ Monitor MultiSync FE750+ Notes Specifications Monitor Picture Tube Diagonal: 17 inch 90° deflection, 0.25 mm grille pitch, Viewable Image Size: 16 inch medium short persistence phosphor, Radius: 50,000 mm aperture grille CRT, multi-layered, anti-static screen coating, dark-tint screen and ® OptiClear screen. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Composite sync. (Positive/Ne
Summary of the content on the page No. 13
Features Flat Aperture Grille CRT: Delivers an unparalleled viewing experience with a virtually flat image, eliminating distortion and reducing glare so that what you see on-screen is what you get on your printed output. The striped phosphor alignment of the CRT delivers superior vertical definition with improved bright- ness for more uniform image contrast. ® OptiClear Screen Surface: Reduces reflection and glare and increases contrast without sacrificing focus level, clarity or brightness. Alo
Summary of the content on the page No. 14
Troubleshooting No picture • Display card should be completely seated in its slot. • Power Button and computer power switch should be in the ON position. • Signal cable should be completely connected to display card/computer. • Check connector for bent or pushed-in pins. Image is scrolling or unstable • Signal cable should be completely attached to the computer. • Check pin assignments and signal timings of the monitor and your display card with respect to recommended timings and pin assignments
Summary of the content on the page No. 15
References • BBS (978) 742-8706 NEC-Mitsubishi Electronics Display Remote Bulletin Board System is an electronic service accessible with your system and a modem. Communication parameters are: 300/1200/2400/9600/14.4k/28.8k/33.6k bps, no parity, 8-data bits, 1 stop bit • Customer Service/ Technical Support (800) 632-4662 Fax (978) 742-7049 • Electronic Channels: Internet e-mail: tech-support@necmitsubishi.com Internet ftp site: ftp.necmitsubishi.com World Wide Web: http://www.necmitsubishi.com Pr
Summary of the content on the page No. 16
Limited Warranty NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase. Spare parts are warranted for ninety (90) days. Replacement parts or unit may be new or refurbished and wil
Summary of the content on the page No. 17
TCO’99 Congratulations! You have just purchased a TCO’99 approved and labeled product! Your choice has provided you with a product devel- oped for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encourag- ing the adaptation of goods and
Summary of the content on the page No. 18
TCO’99 –continued accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. TCO’99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound chlorine and bromine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead
Summary of the content on the page No. 19
Declaration of the Manufacturer We hereby certify that the color monitor ® TM MultiSync FE750+ (JC-17W41) is in compliance with Council Directive 73/23/EEC: – EN 60950 Council Directive 89/336/EEC: — EN 55022 — EN 61000-3-2 — EN 61000-3-3 — EN 55024 (IEC-61000-4-2) (IEC-61000-4-3) (IEC-61000-4-4) (IEC-61000-4-5) (IEC-61000-4-6) (IEC-61000-4-8) (IEC-61000-4-11) and marked with NEC-Mitsubishi Electric Visual Systems Corporation 686-1, Nishioi Oi-Machi Ashigarakami-gun Kanagawa 258-8533, Japan Rönt
Summary of the content on the page No. 20
Notes 18 Fe750+.wpc 20 11/1/00, 10:45 AM
