Summary of the content on the page No. 1
DIAMOND VIEW 1995SL
Colour Monitor
19” (48cm) CRT Size
18” (45.7cm) Viewable Area
User’s Manual
Summary of the content on the page No. 2
UG/MO1995SL/0102/2
Summary of the content on the page No. 3
Table of Contents Important Safety Instructions...........................................1 1 Features .............................................................................2 2 3 Unpacking the Monitor......................................................3 4 Installation .........................................................................3 Drivers for Windows 95, 98, 2000 and Millennium Edition.............4 5 Adjusting the Monitor .....................................................
Summary of the content on the page No. 4
Copyright Notice Copyright 2000, Mitsubishi Electric Australia Pty. Ltd. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission. Disclaimer Mitsubishi Electric Australia Pty. Ltd. makes no representations or warranties, either expressed o
Summary of the content on the page No. 5
Important Safety Instructions 1 Please read the following safety instructions before installing or cleaning your Diamond View monitor: 1. This monitor must be operated from the type of power source indicated on the rating label. If you are not sure of the type of power available in your area, consult your dealer or local electricity supply company. 2. This monitor must be operated with a 3 wire electrical cable that has a plug with a third (grounding) pin. The plug must only be connected to a
Summary of the content on the page No. 6
Features 2 Your Diamond View 1995SL Monitor has the following features: ♦ Plug’n Play Compatibility With DDC1 and DDC2B, the 1995SL is compatible with Plug and Play feature of Microsoft Windows 95, 98, 2000 and Millennium Edition. ♦ Flicker-free Image The monitor supports VESA standard graphics signals with flicker-free refresh rates at resolutions up to 1280 x 1024 pixels at 85Hz. ♦ Larger Viewable Size With its 45.7 cm (18”) viewable size, the 1995SL offers a larger viewable screen are
Summary of the content on the page No. 7
Unpacking the Monitor 3 Please check that the following items are included with your monitor. If they are missing or damaged, please contact your place of purchase immediately. ♦ Monitor with attached signal cable ♦ Power cord ♦ User’s manual Locate the model name and the serial number label on the back of your monitor and write the details of the monitor and your place of purchase in the space on page (ii) of this manual for future reference. Installation 4 Your monitor is equipped with an au
Summary of the content on the page No. 8
3. Connect the computer end of the D- SUB cable to the 15-pin output connector on the video board of your computer. 4. Turn the monitor and the computer on. If you wish to connect the monitor to an older-type Apple Macintosh, you need to use a Macintosh cable adapter to connect the video signal cable of your monitor to the video port of the computer. Your computer dealer should be able to supply you with a suitable adaptor. Drivers for Windows 95, 98, 2000 and Millennium Edition Windows will det
Summary of the content on the page No. 9
Adjusting the Monitor 5 1 2 3 4 5 Exit Enter You can adjust the monitor using its On-Screen Display (OSD) menu system. There are 5 buttons that control the monitor: 1. Exit Returns to the last menu page, saves changes or quits the menu system. 2. and Move to another menu item or decrease the selected 3 parameter. Hotkey for contrast adjustment. 3. and Move to another menu item or increase the selected 4 parameter. Hotkey for brightness adjus
Summary of the content on the page No. 10
Selecting Functions and Making Adjustments Contrast Hotkey 1. Press to open the contrast adjustment display. 2. Press or to adjust the contrast level. 3. Press the Exit button to save your changes. Brightness Hotkey 1. Press to open the brightness adjustment display. 2. Press or to adjust the contrast level. 1. Press the Exit button to save your changes. The Main Menu The Diamond View 1995SL’s OSD has a in Main Menu organised into 6 groups of functions: Luminance, Geometry, Colour Adjustment
Summary of the content on the page No. 11
Make adjustments 1. In Main Menu: Pressor to select the function group with the item that you wish to change. 2. Press Enter to open the Sub Menu. 3. Pressor to select the item to be changed and press Enter. 4. Press or again to make the adjustment. 7
Summary of the content on the page No. 12
etc Sub menu Function name Hor. Position 75 Scale Enter:Save Enter:Save Exit : Exit Exit : Exit 5. Press Exit to save the setting. 6. Press Exit to return to main menu. 1. Luminance Contrast changes the difference between the light and dark areas of the displayed image. Brightness adjusts the brightness of the displayed image. 2. Geometry Hor. Position adjusts the horizontal position of the image. Hor. Size adjusts the image width. Ver. Position adjusts th
Summary of the content on the page No. 13
Unbalance adjusts the pincushion balance if both sides of the image are bowed toward either the left or the right. Trapezoid makes the vertical edges of the image parallel. Parallelogram aligns the top and bottom edges of the image. Top corner adjusts the edge curvature at the top corners of the image. Bottom corner adjusts the edge curvature at the bottom corners of the image. 3. Colour Adjustment Colour mode Colour Temperature Colour Temperature (Preset Mode) (User Mode) C1 (9300K) 9300K User
Summary of the content on the page No. 14
4. Recall/Reset and Image Status Select and press Enter to recall the factory settings for the current graphics signal. The word “Recall” will blink on the screen in the process of recall. This page is also a status display that shows the horizontal and vertical frequencies of the current graphics signal. Please note that the resolution is only displayed if you are using a graphics signal that corresponds with one of the monitor’s presets. 5. Manual degaussing function To eliminate colour shad
Summary of the content on the page No. 15
Note: The setting of each parameter is represented by a numeric value and corresponding scale. The on-screen menu will automatically disappear after 20-second’s of inactivity. If changes have been made, the monitor will automatically save them. Timing and Refresh Rate Setting By making adjustments of your video card settings, you can set the timing and the refresh rate to match your requirements. Please consult your operating system’s and graphics adaptor’s documentation for details about h
Summary of the content on the page No. 16
Factory Preset Timings Mode Resolution Vertical Horizontal Frequency (Hz) Frequency (KHz) Industry 640 x 400 70 31.47 Industry 640 x 480 60 31.47 VESA 800 x 600 75 46.88 VESA 800 x 600 85 53.67 VESA 1024 x 768 75 60.02 VESA 1024 x 768 85 68.68 VESA 1280 x 1024 75 79.98 VESA 1280 x 1024 85 91.15 VESA 1600 x 1200 65 81.25 12
Summary of the content on the page No. 17
Troubleshooting 6 If you encounter any trouble using the Diamond View 1995SL monitor, make sure that your monitor is properly installed. (For hardware installation, see Chapter 4 of this manual.) If the problems persist, please check this chapter for possible solutions before calling Mitsubishi Electric or one of our Authorised Service Centres. No image is displayed - Check that the light (LED) next to the monitor’s power button is lit and is green in colour. - If the LED is orange there is no
Summary of the content on the page No. 18
- Remove any magnetic objects that are near the monitor. These include speakers and power supplies ( AC adaptors ). Colours are impure. - Check that the cable is securely connected to the computer. - Check the VGA signal cable for damage. If any pins are bent or broken off, contact your dealer or an authorised Mitsubishi Electric service agent (see Chapter 11 for details). - Check the monitor’s colour settings. Press the Enter button and select the Color Settings menu. Select the Recall menu ite
Summary of the content on the page No. 19
Specifications 7 Model Diamond View 1995SL Display Characteristics Display Type 19” (48 cm) diagonal short-length cathode ray tube Maximum Viewable Size 18” (45.7cm) diagonal Dot pitch 0.26 mm Surface coating Anti-Glare, Anti-Reflective, Anti- Static coating Graphics Signals Maximum Resolution 1600 x 1200 pixels (at 75 Hz) Recommended Resolution 1280 x 1024 pixels (at 85 Hz) Horizontal Frequency 30 – 95 kHz Vertical Frequency 50 - 160 Hz Video Bandwidth 176 MHz Microprocessor Controlled Graphic
Summary of the content on the page No. 20
User Interface Controls Mains power switch, On-Screen Display with 4 control buttons On-Screen Display Functions: Contrast; Brightness; Vert. & Hor. Image Position and Size; Pincushion Amplitude, Phase and Balance; Top and Bottom Corner Pincushion; Color Balance; Degauss; Horiz. and Vert. Moire; Choice of language (6 language OSD); OSD Position; Status Indicator Physical Characteristics Power Management VESA DPMS, Energy Star Maximum Power Consumption 120 Watts Consumption in Power Saving Mode <
