Summary of the content on the page No. 1
XT-7871
USER'S MANUAL
Features
• 0.28 mm Dot Pitch
• 1280 x 1024, Non-Interlaced
• 120 Hz Refresh Rate
• Power Saving Operation (VESA DPMS)
• Anti-Static, Anti-Glare Screen
• Full Screen Display
• Digital Controls with OSD
• Low Radiation (MPR-II)
• Plug and Play
• Three-Year Warranty
Part #MAN124 Rev. 1.0 XT7871
Summary of the content on the page No. 2
Table of Contents Section 1 General Information ................................................... 2 Section 2 Installation .................................................................. 2 Section 3 Monitor Controls and LEDs ........................................ 3 Section 4 Troubleshooting ......................................................... 6 Appendix A Specifications ............................................................. 7 Appendix B Video Cable Pinout .....................
Summary of the content on the page No. 3
Section 1 - General Information Congratulations on purchasing a MaxTech 17-inch high resolution color monitor. The monitor uses one of the finest CRTs available in the industry. The 0.28 mm dot pitch non-glare tube provides a crisp and vivid color display. The monitor complies with the MPR-II standard to reduce electro-magnetic emissions. Ad- vanced electronics and digital controls make it the perfect monitor for applications ranging from home computing to business presentations. The monitor is
Summary of the content on the page No. 4
Figure 2-1 Monitor Connections Expansion boards COM1 COM2 LPT1 VIDEO Section 3 - Monitor Controls and LEDs 3.1 Controls and LEDs Figure 3-1 Master Power Control 1 3
Summary of the content on the page No. 5
Figure 3-2 Control and LED Locations 2 3 8 7 6 5 4 1. Master Power (On rear): Push to provide power to the monitor. This switch should be left ON for daily operation. Use the front panel On/Off control (3) to turn the monitor display on and off. 2. Power Saving Indicator: When lit, the monitor is in the DPMS OFF mode. 3. ON/OFF: Press this switch to turn the monitor display on, press again to turn the monitor display off. 4. Power On Indicator: When lit the monitor is powered on 5. Adjust: Press
Summary of the content on the page No. 6
3.2 On-Screen Display 1280 X 1024 H: 64KHz V: 60Hz AB C D E F G H I The On-Screen Display (OSD) is enabled by pressing either button of control pair 6 (see Figure 3-2). Control pair 5 (+ and -) buttons are used to increase or decrease the value of selected parameter. A. Horizontal-Size: Adjusts the display width. The (+) button increases the width. The (-) button decreases the width. B. Horizontal-Position: Adjusts the horizontal position. The (+) button moves the display to the right. The (-) b
Summary of the content on the page No. 7
Section 4 - Troubleshooting No picture, no LEDs lit. • Check that the AC cord is plugged into an outlet and the monitor. • Turn on the Master Power switch. No picture, power LED is lit. • Monitor is in DPMS STANDBY/SUSPEND mode. Press a key or move the mouse. • Check that video cable is connected completely. • Adjust brightness and contrast controls. • Check connector for bent pins. No picture, power saving indicator (2) on. • Monitor is in DPMS OFF mode. Press a key or move the mouse. • Monitor
Summary of the content on the page No. 8
Appendix A - Specifications Picture Tube Size 17-inch diagonal Dot pitch 0.28mm Horizontal Freq 30-66KHz Vertical Freq. 50-120 Hz Resolution (Max.) 1280 x 1024 Video Dot Rate 100 MHz Data Area 11.8 in. x 8.7 in. Maximum Refresh Rates Resolution Refresh (Vertical) Frequency 640 x 480 120Hz 800 x 600 100 Hz 1024 x 768 80 Hz 1280 x 1024 60 Hz Input voltage 110~240VAC, 50/60 Hz Front controls On/Off, Adjust, Select, Contrast, Brightness Horizontal-Size, Horizontal-Position, Vertical-Size, Verti- cal
Summary of the content on the page No. 9
Appendix B - Video Cable Pinout Figure B-1 Pin Layout and Pin Assignment Chart PIN SIGNAL PIN SIGNAL 1 Red 9 No Pin 2 Green 10 Ground 6 11 1 3 Blue 11 Ground 4 No Pin 12 SDA 5 Ground 13 Hor. Synch. 10 6 Red Return 14 Vert. Synch 15 5 7 Green Return 15 Data Clock (SCL) 8 Blue Return Appendix C - Power Saving Modes (DPMS) VESA Display Power Management Signaling (DPMS) defines a method for a computer to signal the monitor to reduce its power consumption when idle. DPMS features must be supported by
Summary of the content on the page No. 10
Appendix D - Three Year Warranty MAXTECH warrants to the original buyer of this product against defects in material and workmanship for three years from the date of purchase. Except as specified below, this warranty covers all defects in material or workmanship in this product. The following are not covered by the warranty: 1. Any product which is not distributed in North America by MAXTECH or which is not purchased in North America from an authorized MAXTECH Dealer. 2.Any product on which the s
Summary of the content on the page No. 11
All warranty services must be performed by Authorized Service Centers. There are no user serviceable parts inside the unit. Do not remove any components or attempt to service the unit by any unauthorized service center. This warranty is voided if the product has been abused, misused, modified, or repaired by an unauthorized service center. LIMITATION OF IMPLIED WARRANTIES All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited in duration
Summary of the content on the page No. 12
the receiver is connected • Consult the dealer or an experienced radio / TV technician for help Notice: Shielded cables, if any, must be used in order to comply with the emission limits. Any change or modification not expressly approved by the Grantee of the equipment authorization could void the user’s authority to operate the equipment. Canadian DOC Compliance Statement This equipment does not exceed Class B limits for radio noise emissions for a digital apparatus, set out in the Radio Interfe
