Summary of the content on the page No. 1
V-LCD70P-HDA
7” High Resolution Field Monitor
Operating Instructions
Summary of the content on the page No. 2
2
Summary of the content on the page No. 3
Contents Product Overview .................................................................................................................................................................................4 Features...................................................................................................................................................................................................4 Installation and Initial Setup........................................................
Summary of the content on the page No. 4
Product Overview The V-LCD70P-HDA is a 7.0” high-definition widescreen LCD monitor featuring our completely digital TFT-MegaPixel active matrix LCD platform. With built-in focus assist and false color filters, this monitor is ideal as a light-weight high resolution viewfinder or focus-assist monitor. Our proprietary digital signal processing features 10-bit A/D conversion of all analog signals, with 4X over-sampling and 5-line super-adaptive 2D comb filtering of composite signals. De-inter
Summary of the content on the page No. 5
Installation and Initial Setup Unpacking Carefully unpack the V-LCD70P-HDA monitor and verify that the following items are included: • V-LCD70P-HDA Monitor • V-PS12-5V-XLR Power Supply with 4-Pin Female XLR Connector • Operating Instructions Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States,
Summary of the content on the page No. 6
Front and Side Panel Features Power Button Image Adjustment Knobs Use the power button to toggle between ON and Use the image adjustment knobs to adjust color STANDBY modes. In the STANDBY state, the LED saturation, brightness and contrast of the image. on the button will illuminate bright green. In the ON The status of each image adjustment parameter is state, the LED will dimly illuminate green. shown on the bottom left of
Summary of the content on the page No. 7
Rear Panel Features Component and Composite Input and Output Battery Adapter The V-LCD70P-HDA has HD component (YPbPr) The V-LCD70P-HDA can be powered from a variety and composite inputs, as well as an active loop- of batteries. Several user-interchangeable battery through output for each input. See page 8 for adapters are available. See page 18 for available supported video formats. These input
Summary of the content on the page No. 8
Compatible Input Formats Format Composite YPbPr NTSC PAL 480i 576i 480p / 59.94 576p / 50 720p / 60 720p / 59.94 720p / 50 720p / 30 720p / 29.97 720p / 25 720p / 24 720p / 23.98 1035i / 60 1035i / 59.94 1080i / 60 1080i / 59.95 1080i / 50 1080psF / 24 1080psF / 23.98 1080p / 30 1080p / 29.97 1080p / 25 1080p / 24 1080p / 23.98 8
Summary of the content on the page No. 9
On-Screen Menu STRUCTURE OVERVIEW Color Temperature D93, D65, D55, User RGB Bias and Gain R, G, B Bias (0-100) / R, G, B Gain (0-100) Check Field Off, Mono, Blue, Green, Red Ratio Full Screen, 4:3, 16:9 Video Configuration Pixel-to-Pixel Off, On H/V Delay Off, H & V Delay, V Delay, H Delay Underscan Off, On NTSC Black Level 0 IRE, 7.5 IRE Markers Off, On Center Marker Off, On Off, 4:3, 13:9, 14:9, 1.85:1, 2.35:1, 95% Safe, 16:9 Markers 93% Safe, 90%Safe, 88% Safe, 85% Safe, 8
Summary of the content on the page No. 10
On-Screen Menu (continued) VIDEO CONFIGURATION SUBMENU Video Configuration Submenu Color Temperature Use this setting to choose one of three color temperature presets: • D55 (5500K) • D65 (6500K) • D93 (9300K) • USER (Adjustable Color Bias and Gain) RGB Bias and Gain Select this submenu to adjust bias and gain of the monitor’s response to each color (R, G, B). The bias and gain controls can be used to alter the white balance of the image. Not
Summary of the content on the page No. 11
On-Screen Menu (continued) VIDEO CONFIGURATION SUBMENU (continued) Check Field Use the check field modes for monitor calibration or to analyze individual color components of an image. In Monochrome mode, all color is disabled and only a grayscale image is shown. In Blue, Green, and Red check field modes, all color components but one are disabled. Use the following procedure when calibrating the monitor to SMPTE color bars with the following procedure: 1. Allow the monitor t
Summary of the content on the page No. 12
On-Screen Menu (continued) VIDEO CONFIGURATION SUBMENU (continued) Pixel-to-Pixel Mode Use this setting to enable Pixel-to-Pixel mode. This mode bypasses the monitor’s internal scaling function and displays incoming images in their native resolution and aspect ratio, with a one-to-one mapping: • For incoming formats smaller than the native resolution of the LCD panel (800 x 480), the image will be displayed in the center of the screen using only the necessary LCD pixels.
Summary of the content on the page No. 13
On-Screen Menu (continued) MARKER CONFIGURATION SUBMENU Marker Configuration Submenu Markers Use this setting to enable or disable all on screen markers. This setting affects the center marker, full screen markers, 16:9 markers, and 4:3 markers. Center Marker Use this setting to display a center marker on the screen. 16:9 Markers / Full Screen Markers Use these setting to superimpose one of 11 markers on the screen when in Full Scre
Summary of the content on the page No. 14
On-Screen Menu (continued) MARKER SETUP SUBMENU (continued) 4:3 Markers Use this setting to superimpose one of 5 markers on the screen when in 4:3 mode. This setting is disabled when the aspect ratio is set to 16:9, or when Pixel-to-Pixel, Underscan, or H/V Delay is enabled. • 95% Safe Area • 93% Safe Area • 90% Safe Area • 88% Safe Area • 85% Safe Area • 80% Safe Area 4:3 Marker Examples: OFF (No Marker) 90% Safe Area Marker Background U
Summary of the content on the page No. 15
On-Screen Menu (continued) FILTER CONFIGURATION SUBMENU False Colors The V-LCD70P-HDA has a false color filter to aid the in setting camera exposure. As the camera Iris is adjusted, elements of the image will change color based on the luminance or brightness values. This enables proper exposure to be achieved without the use of costly, complicated external equipment. To best utilize this feature, you must understand the color chart below and have a basic understanding of camer
Summary of the content on the page No. 16
On-Screen Menu (continued) FILTER CONFIGURATION SUBMENU (continued) Peaking Filter (Focus assist) The Peaking Filter is used to aid the camera operator in obtaining the sharpest possible picture. When activated, all color will be removed from the display and a black-and-white image will remain. The internal processor will display RED color on the screen where sharp edges appear. When the camera operator adjusts (racks) the focus control (on the camera lens), different parts of
Summary of the content on the page No. 17
On-Screen Menu (continued) SYSTEM CONFIGURATION SUBMENU System Configuration Submenu Input Format OSD Use this option to enable on-screen display of input/format status in the upper-left corner of the screen. User-Definable Function Buttons Use the Function on F1, F2, F3 and F4 menu items to define each function button on the front panel of the monitor. The following options are available for each button: • Ratio • Check Field • Mosq
Summary of the content on the page No. 18
Specifications PANEL BATTERY ADAPTER Screen Size 7.0” Diagonal Display Area (h x v) 152.40 x 91.44 mm Field-Interchangeable Battery Adapter Options Aspect Ratio 15:9 (16:9 / 4:3 Selectable) (Sold Separately): Pixels 800 x 480 Color Depth 18-bit (262,144 Colors) Marshall Battery Battery Recommended Viewing Angle (h x v) 140° x 100° (CR >10) Adapter Type Voltage Battery 2 Brightness 250 cd/m CM Canon 7.4 V Canon BP-970G Contrast Ratio 400:1 Dot Pitch (h
Summary of the content on the page No. 19
Specifications (continued) Maintenance Screen Cleaning Periodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No. V-HWP-K). A clean micro- fiber cloth can also be used using only non-abrasive and ammonia-free cleaning agents. Do not use paper towels. Paper towel fibers are coarse and may scratch the surface of the polycarbonate faceplate or leave streaks on the surface. Antistatic and fingerprint resistant cleaning age
Summary of the content on the page No. 20
1910 East Maple Ave. El Segundo, CA 90245 Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688 V1.0 www.LCDRacks.com • sales@lcdracks.com 20
