Summary of the content on the page No. 1
User’s Guide
W2043T
W2243T
W2343T
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Summary of the content on the page No. 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Summary of the content on the page No. 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Summary of the content on the page No. 4
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur. (Do not use chemicals such as benz
Summary of the content on the page No. 5
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. Stand Body Stand Base 3. Tie down the base lock to perpendicularity direction. 4. Once assembled take the monitor up carefully and face the front side. Important This i
Summary of the content on the page No. 6
Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on a flat 2. Place the monitor face down on surface. the cushion or soft cloth. 3. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking rib is at a release position, Please push the indicated rib down and retry it. 4. Pull out the stand to remove. A5
Summary of the content on the page No. 7
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5˚~15˚ Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A6 A6
Summary of the content on the page No. 8
Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form to . 1 2 A Connect DVI-D Cable B Connect D-sub Cable (PC) C Connect D-sub Cable (Mac) NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain standard complian
Summary of the content on the page No. 9
Connecting the Display Using the cable holder (This feature is not available in all models.) Cable holder 1 2 4 3 A8 ON PE OPEN OPEN
Summary of the content on the page No. 10
Control Panel Functions Front Panel Controls Control Function Use this button to enter 4:3 IN WIDE, PHOTO EFFECT Button items, for more information, refer to page A17. Use this button to enter or exit from the On Screen Display. MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. The message "OSD LOCKED" appears. You can un
Summary of the content on the page No. 11
Control Panel Functions Control Function Use these buttons to select or adjust functions in the On Buttons Screen Display. Button For more information, refer to page A18. () Use this button to make either D-Sub or DVI Button connector active. This feature is used when two (SOURCE) computers are connected to the display. The default setting is D-Sub. Use this button to select an icon in the On Screen AUTO/SET Display. Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press
Summary of the content on the page No. 12
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make a
Summary of the content on the page No. 13
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu A D Reference To adjust the image size 4:3 IN WIDE NORMAL GAUSSIAN BLUR PHOTO To adjust screen color mode EFFECT SEPIA MONOCHROME BRIGHTNESS To adjust the brightness, contrast and CONTRAST PICTURE gamma of the screen GAMMA sRGB 6500K PRESET 9300K COLOR To costomize the color of the sc
Summary of the content on the page No. 14
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Main Menu MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu : Restart to select sub-menu Button Tip Menu Name Sub-menus Icons NOTE OSD (On Screen Display
Summary of the content on the page No. 15
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE To adjust the brightness of the screen. BRIGHTNESS To adjust the contrast of the screen. CONTRAST Set your own gamma value. : -50/0/50 GAMMA On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR COLOR PRESET • sRGB: Set the screen color to fit the SRGB standard color specificat
Summary of the content on the page No. 16
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING TRACKING HORIZONTAL To move image left and right. VERTICAL To move image up and down. To minimize any vertical bars or CLOCK stripes visible on the screen background. The horizontal screen size will also change. To adjust the focus of the display. PHASE This item allows you to remove any horizontal noise and clear or sharpen the image of characters. MENU : Exit : Decrease SHARPNESS To adjust the clearness o
Summary of the content on the page No. 17
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description SETUP SETUP To choose the language in which the LANGUAGE control names are displayed. OSD To adjust position of the OSD window POSITION on the screen. If the output of the video card is different WHITE BALANCE the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to
Summary of the content on the page No. 18
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the button on the right bottom of the monitor. Main menu Sub menu Description 4:3 IN WIDE To select the image size of the screen. WIDE 4:3 • WIDE: Switch to full screen mode according to input image signal. • 4 : 3: Change the image signal ratio into 4:3. - NORMAL: PHOTO EFFECT The PhotoEffect function is disabled. - GAUSSIAN BLUR: This option is to add the effect to the screen that the dark and sharp ima
Summary of the content on the page No. 19
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the button on the right bottom of the monitor. Menu Name Icons Sub-menu Name Main menu Sub menu Description MOVIE This feature lets you easily select the best desired INTERNET image condition optimized to the environment (ambient illumination, image types etc). MOVIE: For animation images in videos or movies INTERNET: For text images (Word processing etc.) MENU : Exit : Move USER User Yo
Summary of the content on the page No. 20
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. Is the power indicator • Press the Power button. light on? Is the power indicator • If the display is in power saving mode, try moving flickering? the mouse or pressing any key on the keyboard to bring up the screen. • Try to turn on the PC. Do you see an "OUT OF • This me
