Summary of the content on the page No. 1
Contents
CERTIFICATIONS -------------------------------------------------------------------- 2
NOTICE ---------------------------------------------------------------------------------- 2
PRECAUTIONS ---------------------------------------------------------------- 3
SPECIAL NOTES ON LCD MONITORS --------------------------------- 4
BEFORE YOU OPERATE THE MONITOR ------------------------------------- 4
FEATURES -------------------------------------------------------------
Summary of the content on the page No. 2
CE certificate This shipped version of this device complies with the requirements of the EEC directive 89/336/EEC “Electromagnetic compatibility” and 73/23/EEC “Low voltage directive”. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection aga
Summary of the content on the page No. 3
PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit
Summary of the content on the page No. 4
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time. • Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image,
Summary of the content on the page No. 5
INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base 1. During installation, place the display base the right-way up on a flat surface. Place upper part of the display slowly on to the base and wait for the click signifying that it is completely in place. Securely fasten the screw with hands or tools then secure the screws on the bottom with a screwdriver. 2. When removing the rotating base, please place the
Summary of the content on the page No. 6
CONTROLS AND CONNECTORS Adapter Connecting the adapter: Connect one end of the adapter to back of the monitor and connect the other end to the power cord. Power cord Connecting the power cord: Connect one end of the power cord to the AC adapter and connect the other end to the power supply (90V-264V AC Voltage). SIGNAL CABLE Connecting the Signal Cable: the LCD monitor comes with a built-in video cable. Plug the signal cable ′s 15-pin connector into the computer's video po
Summary of the content on the page No. 7
ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You are able to adjust the monitor’s angle from -5 ° to 20 °. ° 20 ° -5 Figure 3 NOTES • Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. • Careful attention is required
Summary of the content on the page No. 8
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power switch to turn the monitor on or off. The other control knobs are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. Figure 4 External Control Button EXTERNAL CONTROLS 1. Auto Config / Exit 2. ▲/ Brightness 3. ▼/ Contrast 4. MENU / ENTER 5. Power / Power indicator 8
Summary of the content on the page No. 9
FRONT PANEL CONTROL • Power / Power indicator : Press this knob to switch ON/OFF of monitor’s power. and display the monitor’s state. Blue — Power On mode. Orange — Power Off mode. • MENU/ENTER / : Activate OSD menu or function adjusts confirmation. • Contrast / ▼: Adjust contrast or function adjustment. • Brightness / ▲: Adjust brightness or function adjustment. • Auto Config Key / EXIT/ : 1. When OSD menu is in active status, this knob will act as EXIT-KEY (E
Summary of the content on the page No. 10
HOW TO USE OSD The main menu will be displayed as follows (see figure 5). If OSD window is in Chinese when power on, press ▲ or ▼ to choose the next window. Choose the English, then press MENU Key . for confirming. OSD window will display in English. 1. Press the MENU-Key . to show the OSD window. See figure 5. 2. Press ▲ or ▼ to select the adjusted item, then press the MENU-key . 3. Press ▲ or ▼ to change the settings of selected item. Press MENU-key . when desired setting is done.
Summary of the content on the page No. 11
3.1 FOCUS Adjust the picture Focus. 3.2 CLOCK Adjust the picture Clock. 4. LANGUAGE Multi-Language selection. 5. OSD TIMER Choose OSD window display time. 6. COLOR TEMPERATURE 6.1 7800K/6500K (COLOR TEMPERATURE) The color temperature for 7800K is x=0.296, y=0.311 and 6500K is x=0.313, y=0.329. It presents two
Summary of the content on the page No. 12
Green monitor • The monitor has a power saving function that conforms to the VESA standard. When the computer input no signal, the monitor will enter the shuts off mode. The power-saving mode can be indicated by the light-emitting diode (LED) on the front panel: Signal Power Mode Cable Picture Indicator Consumption On Attached Active Blue ≤ 42 W Off Attached None Orange ≤ 2 W Off No attached None Orange ≤ 2 W PLUG AND PLAY Plug & Play DDC2B Feature This monitor is eq
Summary of the content on the page No. 13
TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Power Switch is in the ON position *Power Cord should be connected *Check the Power socket. *Replace new Power Cord. No picture, the LED indicator is *The Signal Cable should be completely light up connected to the computer. *If it is orange, then the monitor and the computer are in dormancy mode. You need press your keyboard or move the mouse to reactivate the system. *If it is blu
Summary of the content on the page No. 14
Screen image is not centered or *Adjust pixel frequency (CLOCK) and sized properly. FOCUS or press hot-key (AUTO). Picture has color defects *Adjust RGB color or select color (white does not look white) temperature Poor brightness or contrast *When the brightness of the screen lowers after being used for a certain period and the function of the display is affected, send it to our authorized service center for repair. Horizontal or vertical disturbancies *Use Win 95/98/2000/ME shutdown
Summary of the content on the page No. 15
ERROR MESSAGE & POSSIBLE SOLUTION NO SIGNAL INPUT 1. The computer is switched off. 2. The computer is dormancy. CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT THE RESOLUTION OUT OF THE RANGE: Your computer has been set to unsuitable display mode, Set the computer to display mode given in the following table.
Summary of the content on the page No. 16
APPENDIX A SPECIFICATIONS Type TFT Color LCD Size 43.2cm(17") LCD Panel Pixel pitch 0.264mm( H ) x 0.264mm( V ) Video R,G,B Analog Interface Separate Sync. H/V TTL Input H-Frequency 30kHz - 80kHz V-Frequency 50Hz-75Hz Display Colors 16.2M Colors Dot Clock 135MHz Max. Resolution 1280 x 1024 TM Plug & Play VESA DDC2B Input Connector D-Sub 15pin Input Video Signal Analog:0.7Vp-p(standard), 75 OHM, Positive Maximum Screen Size Horizontal : 337.92mm Vertical : 270.34mm Powe
Summary of the content on the page No. 17
APPENDIX B FACTORY PRESET TIMING TABLE HORIZONTAL VERTICAL RESOLUTION STANDARD FREQUENCY FREQUENCY 720 × 400 31.47kHz 70Hz Dos-modo 640 × 480 31.47kHz 60Hz VGA 640 × 480 37.861kHz 72Hz 640 × 480 37.50kHz 75Hz 800 × 600 37.879kHz 60Hz SVGA 800 × 600 48.077kHz 72Hz 800 × 600 46.875kHz 75Hz 1024 × 768 48.363kHz 60Hz XGA 1024 × 768 56.476kHz 70Hz 1024 × 768 60.02kHz 75Hz 1280 × 1024 64.000kHz 60Hz SXGA 1280 × 1024 80.000kHz 75Hz 17
Summary of the content on the page No. 18
APPENDIX C CONNECTOR PIN ASSIGNMENT 15 6 10 11 15 Figure 6 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Ground 3. Blue 11. Ground 4. Ground 12. DDC-Serial Data 5. Ground 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground 18
