Summary of the content on the page No. 1
L200p
Summary of the content on the page No. 2
Product number 4438-HB6 First Edition (March 2008) © Copyright Lenovo 2008. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are asold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure. LIMITED AND RESTRICTED RIGHTS NOTICE: IF products, data, computer software, or services are delivered pursuant a General Services Adm
Summary of the content on the page No. 3
iii iv Safety and Maintenance Guidelines 1-4 1-4 1-4 1-9 Manually installing the Soft OSM 3-7 3-9 8
Summary of the content on the page No. 4
sUmGanBt’manli¥tl¥n; muneBlcab;epIþmbBa©Úlkm μviFI 8. iii
Summary of the content on the page No. 5
Safety and Maintenance Guidelines iv
Summary of the content on the page No. 6
This User’s Guide contains detailed information on the ThinkVision™ L200p Wide Flat Panel Monitor. For a quick overview, please see the Setup Poster that was shipped with your monitor. Digital Interface Cable N o t e:To attach a VESA mount, please see “Detaching the monitor stand” on page 2-7. 8
Summary of the content on the page No. 7
Product overview This section will provide information on adjusting monitor positions, setting user controls, and using the cable lock slot. Types of adjustments Tilt Please see the illustration below for an example of the tilt range. Swivel With the built-in pedestal, you can tilt and swivel the monitor for the most comfortable viewing angle. o o -45 45 Height Adjustment After pressing the top of the monitor, remove the fixed pin and adjust the heigh
Summary of the content on the page No. 8
Monitor Pivot O 9 0 - Adjust height to the top position before rotation the monitor. - Rotate clockwise until the monitor stops at 90°. User controls Your monitor has controls on the front which are used to adjust the display. For information on how to use these controls, please see “Adjusting your monitor image” on page 2-3. Chapter 1. Getting started 1-3
Summary of the content on the page No. 9
Cable lock slot Your monitor is equipped with a cable lock slot located on the rear of your monitor (in the lower right corner). Please follow the instructions that came with the cable lock to attach it. Setting up your monitor This section provides information to help you set up your monitor. Connecting and turning on your monitor N o t e : Be sure to read the Safety Information located in the Monitor Safety, Troubleshooting, and Warranty Guide before carrying out this procedure. 1. Power off y
Summary of the content on the page No. 10
3. Connect the analog signal cable to the D-SUB connector of the monitor and the other end on the back of the computer. 4. Plug the monitor power cord and the computer cord into grounded electrical outlets. Note: A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord 2 according to IEC 60227 (designation H05V
Summary of the content on the page No. 11
5. Remove the Cable Cover from the back of the stand. 2 1 6. Rotate the head of the monitor into portrait view. 1 - 6 L200p Wide Flat Panel Monitor User’s Guide
Summary of the content on the page No. 12
7. Place the cables through the Main Clip. Then fasten the clip. 8. Wrap the Cable Wapper around the cables. 9. Rotate the Hook. 1 - 7 Chapter 1. Getting started
Summary of the content on the page No. 13
10. Replace the Cable Cover. 2 1 11. Power on the monitor and the computer. 12. To install the monitor driver, insert the Reference and Driver CD, click I n s t a l l d r i v e r, and follow the on-screen instructions. 1 - 8 L200p Wide Flat Panel Monitor User’s Guide
Summary of the content on the page No. 14
13. To optimize your monitor image, if using the analog cable, press the Automatic Image Setup key. Automatic image setup requires that the monitor is warmed up for at least 15 minutes. This is not required if you are using the DVI cable. N o t e : If automatic image setup does not establish the image that you prefer, perform manual image setup. See “Manual image setup” on page 3-2 Registering your option ™ Thank you for purchasing this Lenovo product. Please take a few moments to register you
Summary of the content on the page No. 15
f t t t lenovo. f t t t f t t t t f 8
Summary of the content on the page No. 16
v Use adequate lighting for the type of work you are performing. v Use the monitor brightness, contrast, and image adjustment controls, if equipped, to optimize the image on your screen to meet your visual preferences. v Keep your monitor screen clean so you can focus on the screen’s contents. Any concentrated and sustained visual activity can be tiring for your eyes. Be sure to periodically look away from your monitor screen and focus on a far object to allow your eye muscles to relax. If you h
Summary of the content on the page No. 17
Adjusting your monitor image This section describes the user control features used to adjust your monitor image. Using the direct access controls The direct access controls can be used when the On Screen Display (OSD) is not displayed. Note: The direct access controls are blue. Table 2-1. Direct access controls Icon Control Description Input Change Switches the video input source. Image Setup Activates automatic image adjustment. Brightness Direct access to Brightness adjustment. Using the On-Sc
Summary of the content on the page No. 18
Table 2-2. OSD functions C Co on nt tr ro ol ls s a an nd d C Co on nt tr ro ol ls s a an nd d C Co on nt tr ro ol ls s a an nd d C Co on nt tr ro ol ls s a an nd d O OS SD D I Ic co on n o on n M Ma ai in n A Ad dj ju us st tm me en nt ts s A Ad dj ju us st tm me en nt ts s O OS SD D I Ic co on n o on n M Ma ai in n A Ad dj ju us st tm me en nt ts s A Ad dj ju us st tm me en nt ts s M Me en nu u S Su ub bm me en nu u D De es sc cr ri ip pt ti io on n ( (A An na al lo og
Summary of the content on the page No. 19
Table 2-2. OSD functions C Co on nt tr ro ol ls s a an nd d C Co on nt tr ro ol ls s a an nd d O OS SD D I Ic co on n o on n M Ma ai in n S Su ub bm me en nu u D De es sc cr ri ip pt ti io on n A Ad dj ju us st tm me en nt ts s A Ad dj ju us st tm me en nt ts s M Me en nu u ( (A An na al lo og g) ) ( (D Di ig gi it ta al l) ) Same as Analog This monitor can accept video signals through two different connectors. Most desktop computers use Input signal a D-SUB connector. Select
Summary of the content on the page No. 20
Selecting a supported displa y mode The display mode the monitor uses is controlled by the computer. Therefore, refer to your computer documentation for details on how to change display modes. The image size, position and shape might change when the display mode changes. This is normal and the image can be readjusted using automatic image setup and the image controls. Unlike CRT monitors, which require a high refresh rate to minimize flicker, LCD or Flat Panel technology is inherently flicker-fr
