Summary of the content on the page No. 1
LZ-651W_ENG r2 03.7.25 9:50 AM Page 1
WIDE SCREEN MONITOR
LZ-651W
INSTRUCTION MANUAL
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best
performance from your new LZ-651W.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on
the warranty card, and in the space provided below. Refer to the model and serial
numbers whenever you call upon your KENWOOD dealer f
Summary of the content on the page No. 2
English LZ-651W_ENG r2 03.7.25 9:50 AM Page 2 Before Use Safety Precaution 2WARNING To prevent injury and/or fire, take the following precautions: • Ensure that the unit is securely installed. Otherwise it may fly out of place during collisions and other jolts. • When extending the ignition or ground cables, make sure to use automotive-grade cables or 2 other cables with an area of 0.75mm (AWG18) or more to prevent wire deterioration and damage to the wire coating. •To prevent short circuits,
Summary of the content on the page No. 3
LZ-651W_ENG r2 03.7.25 9:50 AM Page 3 LZ-651W Basic Operation 8 Audio Source Select button Each time the button is pressed the audio source switches as follows: BAND DISC BAND DISC NORMAL Sound of monitoring picture selected by [Video Source OUT OUT Select] button. M/S M/S ZOOM ZOOM MENU MENU CANCEL MENU NAV CANCEL MENU Sound of navigation system. IN IN PWR SRC PWR SRC AV-IN Sound of input video picture POS ROUTE POS ROUTE NAV/ from AV-IN. NAV/ DIRECT ATT VIDEO DIRECT ATT VIDEO OFF No soun
Summary of the content on the page No. 4
English LZ-651W_ENG r2 03.7.25 9:50 AM Page 4 Setup Menu Setting Menu MENU MENU Press button. 1 Menu screen is displayed, and the monitor enters to menu mode. Press or button to select the adjusting item, 2 ENTER VOICE and press button. "SCREEN CONTROL": Adjust the picture quality (brightness, contrast etc.). "SETUP": Setup the picture input method and the beep sound. Screen control MENU MENU Press button. 1 ENTER VOICE Select "SCREEN CONTROL", and press button. 2 Press or button to select th
Summary of the content on the page No. 5
LZ-651W_ENG r2 03.7.25 9:50 AM Page 5 Setup MENU MENU Press button. 1 ENTER VOICE Select "SETUP", and press button. 2 Press or button to select the adjusting item. 3 "NAV": Setup input and switch method of the navigation picture. Item Setting "RGB"* When Kenwood navigation system is connected by the dedicated cable. "AV-IN" When connected to AV-IN terminal be composite signal cable. "OFF" It doesn’t switch the navigation picture. *Default setting If you set to "OFF" while the audio source is
Summary of the content on the page No. 6
English LZ-651W_ENG r2 03.7.25 9:50 AM Page 6 Installation Accessories A B C D (Ø4 x 12 mm) E The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. Installation Procedure 1. To prevent short circuits, remove the key from the installation bracket. the ignition and disconnect the · terminal of the •If you are not going to install the unit using the battery. supplied monitor stand, be
Summary of the content on the page No. 7
LZ-651W_ENG r2 03.7.25 9:50 AM Page 7 Connection Monitor Unit AV input Audio input (MONO) AV cable (Commercially available) Visual input Navigation Unit Bundle cables with the clamper (Accessory A) Cable accompanying the Navigation System When you connect the Mute Cable to the Navigation System, the voice of the Navigation guide will interrupt. Mute cable (Brown) NAVI MUTE Fuse (2A) Ignition key switch Connect TEL mute cable of ACC the navigation system. ACC Ignition cable (Red) +12V 2CAUTION
Summary of the content on the page No. 8
English LZ-651W_ENG r2 03.7.25 9:50 AM Page 8 Installation Installation for Monitor Unit Installation location and cleaning Select for installation a location where the stand can be placed completely horizontal or where the front edge of AB C the support (petal-shaped part) can be attached horizontally as shown in Figure A. Do not install in locations where the entire support is at a diagonal such as in Figure B or where the monitor unit is facing down such as in Figure C. 2CAUTION Thoroughly
Summary of the content on the page No. 9
LZ-651W_ENG r2 03.7.25 9:50 AM Page 9 Troubleshooting What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. The power does not turn on. • The fuse has blown. • After checking for short circuits in the cables, replace the fuse with one having the same rating. • No ACC position on vehicle ignition. • Connect the same cable to the ignition as the battery cable.
Summary of the content on the page No. 10
English LZ-651W_ENG r2 03.7.25 9:50 AM Page 10 FCC WARNING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
