Summary of the content on the page No. 1
HP LD4200 and LD4700 LCD Monitors
User Guide
Summary of the content on the page No. 2
© 2009, 2010 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contai
Summary of the content on the page No. 3
About This Guide This guide provides information on setting up the monitor, installing drivers, using the on-screen display menu, troubleshooting and technical specifications. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supp
Summary of the content on the page No. 4
iv About This Guide ENWW
Summary of the content on the page No. 5
Table of contents 1 Product Features ............................................................................................................................................ 1 HP Digital Signage Models ................................................................................................................... 1 2 Safety and Maintenance Guidelines .............................................................................................................. 2 Important Safety Informat
Summary of the content on the page No. 6
OSD Menu Selections ....................................................................................................... 25 Selecting An Aspect Ratio Mode ....................................................................................... 28 Adjusting the Timer Function ............................................................................................. 29 Clock ................................................................................................................. 29 On
Summary of the content on the page No. 7
13. Remote Lock /Key Lock (Command : m) ..................................................................... 49 14. Balance (Command : t) ................................................................................................ 50 15. Color Temperature (Command : u)v ............................................................................ 50 16. Abnormal state (Command : z) .................................................................................... 51 17. ISM mode (Command:
Summary of the content on the page No. 8
Appendix D Agency Regulatory Notices ....................................................................................................... 66 Federal Communications Commission Notice ................................................................................... 66 Modifications ...................................................................................................................... 66 Cables ....................................................................................
Summary of the content on the page No. 9
1 Product Features HP Digital Signage Models The HP LCD digital signage monitors have a wide aspect active matrix thin-film transistor (TFT) panel. The monitors feature: ● LD4200 model, 106.7 cm (42-inch) widescreen diagonal viewable area display with 1920 x 1080 native resolution LD4700 model, 119.28 cm (47-inch) widescreen diagonal viewable area display with 1920 x ● 1080 native resolution ● Wide viewing angle up to 178° horizontal and 178° vertical ● Landscape or portrait wall mounting positi
Summary of the content on the page No. 10
2 Safety and Maintenance Guidelines Important Safety Information A power cord is included with the monitor. If another cord is used, use only a power source and connection appropriate for this monitor. For information on the correct power cord set to use with the monitor, refer to the Power Cord Set Requirements on page 68. WARNING! To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding feature. The grounding plug is an important safety feature
Summary of the content on the page No. 11
cord does not exceed the rating of the cord. Look on the power label to determine the ampere rating (AMPS or A) for each device. ● Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord. Turn the monitor off when not in use. You can substantially increase the life expectancy of the ● monitor by using a screen saver program and turning off the monitor when not
Summary of the content on the page No. 12
3 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow the instructions below. Installing the Stand (Sold Separately) 1. Remove the screws (1), monitor stand (2) and cable management clip (3) from the box. NOTE: The LD4200 stand uses six M4 x 12mm screws. The LD4700 stand uses four M4 x 26mm screws. Figure 3-1 LD4200 Stand Accessory Contents Figure 3-2 LD4700 Stand Accessory Contents 4 Chapter
Summary of the content on the page No. 13
2. Place a soft cloth on the table and place the product with the screen facing downward. Connect the stand as shown in the following illustrations. Figure 3-3 Sliding the LD4200 Stand Onto the LD4200 Monitor Figure 3-4 Sliding the LD4700 Stand Onto the LD4700 Monitor ENWW Installing the Stand (Sold Separately) 5
Summary of the content on the page No. 14
3. Use the screws to secure the stand to the rear side of the product. Figure 3-5 Securing the LD4200 Stand to the LD4200 Monitor Figure 3-6 Securing the LD4700 Stand to the LD4700 Monitor Connecting the Speakers (Sold Separately) 1. Mount the speakers onto the product. Figure 3-7 Mounting the Speakers 6 Chapter 3 Setting Up the Monitor ENWW
Summary of the content on the page No. 15
2. Use the four Taptite D3 x 12mm screws to secure the speakers to the monitor. Figure 3-8 Securing the Speakers to the Monitor ENWW Connecting the Speakers (Sold Separately) 7
Summary of the content on the page No. 16
3. After installing the speakers, use the cable holders and cable ties (available on select models) to organize the speaker cables. Figure 3-9 Using the Cable Holders (Feature Available on Select Models) Figure 3-10 Using the Cable Ties (Feature Available on Select Models) 8 Chapter 3 Setting Up the Monitor ENWW
Summary of the content on the page No. 17
4. After installing the speakers, connect the input terminal with a proper color match. Figure 3-11 Connecting to the Input Terminal Rotating to the Portrait Position (Select Models) When installing the monitor in the portrait position, rotate it clockwise based on its front. The monitor can be rotated in only one direction. NOTE: The monitor cannot be rotated if it is installed on the stand. Figure 3-12 Installing Portrait ENWW Rotating to the Portrait Position (Select Models) 9
Summary of the content on the page No. 18
Using the Remote Control Inserting the Batteries 1. Slide off the battery cover. 2. Insert the batteries with correct polarity (+/-). 3. Close the battery cover. NOTE: Dispose of used batteries in the recycle bin to prevent environmental pollution. Figure 3-13 Inserting Batteries 10 Chapter 3 Setting Up the Monitor ENWW
Summary of the content on the page No. 19
Identifying Remote Control Buttons Figure 3-14 Remote Control Buttons Component Function 1 AV Toggles through video: AV > Component1 > Component2 > RGB PC > HDMI/DVI. 2 Sleep When watching AV, RGB PC, HDMI/DVI, Component1, Component2, the product will be automatically turned off after a certain period of time. Press the button repetitively to select an appropriate time duration. 3 PSM Toggles through present video settings. 4 Menu Opens the menu selection. 5 Up and Down Provides up and down dir
Summary of the content on the page No. 20
Component Function 11 Exit Exits the menu. 12 Volume Adjusts the sound up and down. 13 Set (Check) Press to select a menu item or save changes. Identifying Rear Components Figure 3-15 Rear Components (The product image in the user guide could be different from the actual image) Component Function 1 Power connector Connects the AC power cord to the monitor 2 RS-232C serial ports Connects to RS-232 devices 3 RGB PC, HDMI/DVI Ports HDMI supports High Definition input and HDCP (High-bandwidth Digit
