Summary of the content on the page No. 1
HMLCD19
19-inch LCD Monitor
User Manual
Video Systems
www.honeywellvideo.com
1-800-796-CCTV
© 2004 Honeywell International Inc.
All rights reserved. No part of this publication may be reproduced by any means
without written permission from Honeywell Video Systems. The information in
this publication is believed to be accurate in all respects. However, Honeywell
Video Systems cannot assume responsibility for any co
Summary of the content on the page No. 2
SECTION 5: SPECIFICATIONS ISSUE DATE REVISIONS A April 2004 Initial Release (PCN 1632) LCD Type TFT Color Screen Size 19” (diagonal) PC Input Signal RGB Analog Type 15-Pin D-Sub Sync H-Freq 31.5~80KHz V-Freq 56~75Hz Display Color 16,777,216 (24 bit) Resolution 1280 x 1024 @ 75Hz Video Band Width 162MHz Max OSD Controls PICTURE (Auto Adjustment, Horizontal Position, Vertical Position, Horizontal Size, Phase, DOS/Graphic), COLOR (Auto Adjustment, Brightness, Contrast, Temper
Summary of the content on the page No. 3
4.4 LIMITED WARRANTY FCC COMPLIANCE STATEMENT Honeywell International Inc. ("Seller"), 1305 Waters Ridge Drive, Lewisville, TX 75057, warrants this monitor to be in conformance with its own plans and specifications and to INFORMATION TO THE USER: This equipment has been be free from defects in materials and workmanship under normal use and service for a tested and found to comply with the limits for a Class A digital period of up to one (1) year from the date of manufacture. Seller
Summary of the content on the page No. 4
SECTION 4: TROUBLESHOOTING AND MAINTENANCE EXPLANATION OF GRAPHICAL SYMBOLS 4.1 TROUBLESHOOTING No Power The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the • Make sure the Power cable is plugged to the wall and the presence of uninsulated "dangerous voltage" within the back of the monitor. product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. • Make sure that the Powe
Summary of the content on the page No. 5
3.4 GETTING OPTIMAL PICTURE WARNINGS Step 1: Window’s background or “H” character should be displayed on your screen. • Installation and servicing should be performed only by qualified and experienced personnel. Step 2: Adjust the screen to the center of the Display (LCD) by using the top and bottom display controls and the V-Position Adjust menu. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. SAFEGUARDS This product is made with consid
Summary of the content on the page No. 6
3.3 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE, CONTINUED SAFEGUARDS, CONTINUED Using HOTKEY ENVIRONMENT/INSTALLATION WARNINGS Frequent adjustments such as auto-geometry, Brightness, 2. Do not place candlelight, mosquito coils, or cigarettes on top of the Contrast, Audio-volume, Audio-Mute, and Source (selected in monitor or install it close to heating appliances. Doing so may damage the product or create a fire danger. The product should RGB/VIDEO) can be quickly done without call
Summary of the content on the page No. 7
3.3 ON-SCREEN DISPLAY (OSD) CONTROL SAFEGUARDS, CONTINUED PROCEDURE, CONTINUED CLEANING AND GENERAL USAGE OSD Menu Description 1. For added protection of this unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it OSD Horizontal position Select OSD MENU horizontal position. from the wall outlet and disconnect the cable system. This will Vertical position Select OSD MENU vertical position. prevent damage to the unit due to lightni
Summary of the content on the page No. 8
3.3 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE, CONTINUED PURCHASE INFORMATION OSD Menu Description Date Purchased: The following table describes the OSD menu and a description Serial Number: of each option. Location Installed: OSD Menu Description Picture Auto adjustment Automatically adjusts the Horizontal position, Vertical position, horizontal size and Phase. Windows background or characters should be displayed on the full screen prior to processing this function. H
Summary of the content on the page No. 9
3.3 ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE TABLE OF CONTENTS Image and sound can easily be adjusted through an OSD menu. SECTION 1: INTRODUCTION .................................................. 1 1.1 INTRODUCTION .............................................................1 1.2 FEATURES......................................................................1 1.3 CONTENTS OF PACKAGE .............................................3 SECTION 2: CONTROLS AND CONNECTIO
Summary of the content on the page No. 10
3.2 PRESET MODE CHART, CONTINUED TABLE OF CONTENTS, CONTINUED Timing Charts Horizontal Pixel 640 640 640 640 720 800 800 800 800 SECTION 4: TROUBLESHOOTING AND MAINTENANCE.... 19 Frequency KHz 31.469 31.469 37.862 37.500 31.469 35.156 37.879 48.077 46.875 Period (T1) ms 31.778 31.778 26.413 26.667 31.778 28.444 26.400 20.800 21.333 4.1 TROUBLESHOOTING...................................................19 Sync Width (T2) ms 2.542 3.813 1.270 2.032 3.813 2.000 3.200 2.400 1.616 No Powe
Summary of the content on the page No. 11
SECTION 1: INTRODUCTION 3.2 PRESET MODE CHART 1.1 INTRODUCTION Timing Charts The monitor shall be capable of supporting the following video Honeywell's HMLCD19 SXGA Color LCD Display features a 19" timings: viewable active matrix LCD screen, with outstanding 1280 x 1024 pixel resolution. When used in PC based applications the VIDEO HMLCD19 provides connection points for VGA, PC Sound, and (T4) Active Headphones. CCTV applications are supported by input connections for audio, Y/C
Summary of the content on the page No. 12
SECTION 3: OPERATION Some computer systems are not compatible 3.1 POWER MANAGEMENT with the DDC standard. If your monitor is displaying the wrong resolution, check your computer system for a DDC compatible video This monitor is equipped with DPMS (Display Power card and contact the Service Center. Management Signaling) function which automatically switches to power saving mode (less than 5 watts consumed) when the computer is left unattended. Although the monitor can be left in
Summary of the content on the page No. 13
USER MANUAL NOTES: 1.3 CONTENTS OF PACKAGE LCD Monitor User Manual VGA Cable Sound Cable AC/DC Adapter Installation Disk Power Cord Video Sound Cable Composite Cable BNC to RCA Adapters (2) OPTIONAL ACCESSORIES: S-video cable, Wall Mount adapter (VESA standard) Rev. A 10 HMMU000882 Rev. A 3 HMMU000882 04/09/04 04/09/04
Summary of the content on the page No. 14
NOTES: 2.6 DISPLAY MODES MEMORY The microcontroller has memory capacity to store 27 different display modes including timing formats and display settings. This memory capacity is divided into two parts: user setting area and factory presetting area. User Setting Area The user can add non-standard modes. If display image is adjusted, the image is saved automatically, then when the microcontroller is turned on it detects and displays the last mode stored in the user setting area.
Summary of the content on the page No. 15
SECTION 2: CONTROLS AND CONNECTIONS 2.5 MICROCONTROLLER FEATURES The microcontroller automatically detects the video board 2.1 CONTROLS – FRONT PANEL installed in your system. When the monitor is turned on, the microcontroller first checks the display mode memory stored in the user setting area and the factory presetting area. A B C D E F G H I J K A AV1 F AUTO/EXIT LAMP B PC G BRT C SOURCE H CONT D CH I VOL E MENU/SEL J MUTE K POWER BUTTON Rev. A 8 HMMU
Summary of the content on the page No. 16
2.2 CONTROLS – REAR PANEL 2.3 INSTALLING THE MONITOR DRIVER You can achieve an optimal resolution and scanning rate by CD B E installing the monitor driver as follows: A F G 1. Insert the monitor driver diskette into the floppy diskette drive and run INSTALL.EXE. 2. Select the monitor model then press OK. The installation will begin immediately. 2.4 VGA CABLE A 15-pin D-Sub connector is used as the input signal connector. Pin and input signal are shown in the table below. DVR o
