Summary of the content on the page No. 1
19 inch TFT LCD Monitor
HS191
USER’S MANUAL
Summary of the content on the page No. 2
User’s Manual Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
Summary of the content on the page No. 3
User’s Manual Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO’03 Display requirements: Ergonomics • Good visual ergonom
Summary of the content on the page No. 4
User’s Manual Recycling Information We, the HannStar Display Corp. care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life. These devices contain recyclable materials, which can be re-decomposed and re-integrated intobrand-new marvels. On the contrary, other material can be classified to hazardous and poisonedsubstances. We strongly enco
Summary of the content on the page No. 5
User’s Manual TABLE OF CONTENTS SAFETY NOTICE ........................................................................................... 6 PRECAUTIONS......................................................................................... 6 SPECIAL NOTES ON LCD MONITORS ................................................... 7 BEFORE YOU OPERATE THE MONITOR.................................................... 8 FEATURES ......................................................................
Summary of the content on the page No. 6
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interferenc
Summary of the content on the page No. 7
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of
Summary of the content on the page No. 8
User’s Manual BEFORE YOU OPERATE THE MONITOR FEATURES • 19” TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions: 1280 X 1024 @60Hz ® • EPA ENERGY STAR • Ergonomic Design • Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor (Reference only, the real feature is depended on selected model) Screen Base Cables and User manual Power Cord VGA Cable Au
Summary of the content on the page No. 9
User’s Manual INSTALLATION INSTRUCTIONS Install Remove Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base. A clear click sound will affirm that the base is connected correctly. 4. Verify that the monitor is securely attached to the base by looking at the bottom of the base and making sure that the clips are fully enga
Summary of the content on the page No. 10
User’s Manual CONTROLS AND CONNECTORS CABLE CONNECTIONS: Turn off your computer before performing the procedure below. 1. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 2. Connect one end of the 24-pin DVI-D cable (Dual input mode optional) to the back of the monitor and connect the other end to the computer’s DVI-D port. 3. Connect the audio cable between the monitor's audio input and the PC's audio
Summary of the content on the page No. 11
User’s Manual ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You are able to adjust the monitor’s angle from 0° to 20°. monitor’s angle Figure.3. NOTES: • Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. • Be carefu
Summary of the content on the page No. 12
User’s Manual OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the Signal cable from the monitor to the VGA card. • Press the power button to turn on the monitor position. The power indicator will light up.
Summary of the content on the page No. 13
User’s Manual FRONT PANEL CONTROL • Power Button: Press this button to switch ON/OFF of monitor’s power. • Power Indicator: Green — Power On mode. Orange — Off mode. • MENU / ENTER: 1. Activate the OSD menu or adjust the function settings and confirmation or 2. Exit OSD menu when in volume OSD status. • Volume < >: 1. Activates the volume control when the OSD is OFF. 2. Navigate through adjustment icons when OSD is ON or adjust a function when function is activated. •
Summary of the content on the page No. 14
User’s Manual HOW TO ADJUST A SETTING OSD Diagram OSD Description Brightness adjustment: Select the 「Brightness 」option on the 「Main Menu 」. Enter the option and adjust the level. Contrast adjustment: Select the 「Contrast 」option on the 「Main Menu 」. Enter the option and adjust the level. How to adjust screen position and quality: Select 「Image Setting 」on the 「Main Menu 」, and then enter the option. Horizontal position adjustment: Select the 「H-position 」option to shift
Summary of the content on the page No. 15
User’s Manual OSD Diagram OSD Description Clock adjustment: Select the 「Clock Adjustment 」option to reduce the vertical flicker of characters on the screen. Enter the option and adjust the level. Phase adjustment: Select the 「Phase Adjustment 」option to reduce the horizontal flicker of characters on the screen. Enter the option and adjust the level. How to adjust color: Select the 「Color Setting 」option on the 「Main Menu 」, and then enter the option. Move the cursor to
Summary of the content on the page No. 16
User’s Manual OSD Diagram OSD Description How to set the OSD: Select 「OSD Setting 」on the 「Main Menu 」, and then enter the option. OSD horizontal adjustment: Select the 「OSD H-Position 」option to adjust the horizontal position of the OSD. Enter the option and adjust the level. OSD vertical position adjustment: Select the 「OSD V-Position 」option to adjust the vertical position of the OSD. Enter the option and adjust the level. OSD timer setting: Select the 「OSD Time-
Summary of the content on the page No. 17
User’s Manual OSD Diagram OSD Description OSD color setting: Select the 「OSD Color 」setting option to adjust the color of the OSD. Enter the option and adjust the level. Language: Select the 「Language 」 option to change the language of the OSD. Enter the option and select a language. (Reference only, the OSD Language is depended on selected model) Volume adjustment: Select the 「Volume 」option to change the volume level. Enter the option and adjust the level. Sharpn
Summary of the content on the page No. 18
User’s Manual OSD Diagram OSD Description Recall the factory settings: Select the 「Factory Preset 」 option to reset to the monitor’s default setting. This will erase the current settings. Enter the option and select On or Off. Input Setting: Select the 「Input Setting 」 option to change between the analog (D-Sub) or Digital (DVI) source. Enter the option and select Analog or Digital. PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabi
Summary of the content on the page No. 19
User’s Manual TECHNICAL SUPPORT (FAQ) Q & A FOR GENERAL DEFECTIVE PROBLEM & QUESTION POSSIBLE SOLUTION *Check if the Power Switch is in the ON position Power LED is not on *Power Cord should be connected *Check if the PC system is Plug & Play compatible No Plug & Play *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent Picture is dim, bright or *Adjust the Clock, Phase, Contrast or Brightness fuzzy Controls. Picture bounces or a wav
Summary of the content on the page No. 20
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table. FACTORY PRESET TIMING TABLE: HORIZONTAL VERTICAL MODE RESOLUTION FREQUENCY (KHz) FREQUENCY (Hz) 1
