Furuno MU-150C user manual

User manual for the device Furuno MU-150C

Device: Furuno MU-150C
Category: Computer Monitor
Manufacturer: Furuno
Size: 1.53 MB
Added : 9/13/2013
Number of pages: 40
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Furuno MU-150C. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Furuno MU-150C.

For your convenience

If looking through the Furuno MU-150C user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Furuno MU-150C on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Furuno MU-150C to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Furuno MU-150C User manual - Online PDF
Advertisement
« Page 1 of 40 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Furuno MU-150C but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Furuno MU-150C. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

MULTI-PURPOSE LCD DISPLAY
MU-150C

Summary of the content on the page No. 2

Summary of the content on the page No. 3

SAFETY INSTRUCTIONS Safety Instructions for the Operator Safety Instructions for the Installer WARNING WARNING Do not open the equipment. Do not open the cover unless totally familiar with Only qualified personnel electrical circuits and should work inside service manual. the equipment.

Summary of the content on the page No. 4

TABLE OF CONTENTS FOREWORD ........................................................................................................ iii SYSTEM CONFIGURATION................................................................................ iv EQUIPMENT LISTS .............................................................................................. v 1 MOUNTING ...................................................................................................... 1 1.1 Display Unit......

Summary of the content on the page No. 5

FOREWORD A Word to the Owner of the MU-150C FURUNO Electric Company thanks you for purchasing the MU-150C 15” Multi-Purpose LCD Display. We are confident you will discover why the FURUNO name has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered by our extensive global network of agents and dealers. Your equipment

Summary of the content on the page No. 6

SYSTEM CONFIGURATION RGB Radar, Video Plotter, Navigator, Video Sounder, Scanning Sonar, etc. 24 VDC or Control unit of 100 - 240 VAC Video Sounder (e.g., FCV-1200 series) NMEA 0183 Navigator (GPS, etc.)* * = When using the FCV-1200 series or CH-250, NMEA 0183 data may be output to the MU-150C instead of the interface unit. Connectable equipment MU-150C Display Unit Type Equipment Landscape Portrait* FR-1500 MK3 series Yes No FCV-1200 series Yes Yes (Modification required) FCV-150

Summary of the content on the page No. 7

EQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks AC specification Display Unit MU-150C − 1 DC specification SP10-02801 001-414-460 For DC Spare Parts * 1 set SP10-02802 001-414-970 For AC For AC (CP10-04901) CP10-04910 001-414-690 Installation Materials * 1 set CP10-04920 001-414-700 For DC (CP10-04902) FP10-02501 001-414-490 1 set Accessories * FP10-05401 001-402-540 1 For FCV-1500L Bracket * FP10-02510 001-414-510 1 Including FP10-02511 Option Name Type

Summary of the content on the page No. 8

1 MOUNTING Refer to the outline drawing at the end of the manual for mounting dimensions. Note: The LCD is made of glass. Handle it with care. 1.1 Display Unit The display unit may be flush mounted in a panel or on a desktop, using the optional bracket. Display tilt can be chosen from 9° or 20°, by the location of the mounting plate. When selecting a mounting location, keep in mind the following points: • Locate the unit out of direct sunlight. • Select a location where the di

Summary of the content on the page No. 9

384 0.5 366 1 15 0.5 See Note 2. Cover Display Unit Display unit and cover 3. Fasten the display unit to the mounting location with six tapping screws (5X30). Note 1: Hex head bolts may also be used to fasten the display unit. However, their length must be at least 30 mm. Note 2: Use M5 bolt or tapping screw (nominal diameter: M5), although the size of the mounting holes in the display unit is M8. 384 – 0.5 333 – 0.5 366 – 1 315 – 1 15 – 0.

Summary of the content on the page No. 10

Desktop mounting The display unit can be mounted on a desktop, using the optional bracket (Type: FP10-02510, Code No.: 001-414-510). 1. Fasten the mounting base (lower) to the mounting location with four sets of hex head bolts, spring washers, flat washers and nuts. Hex Head Bolt Spring Washer Flat Washer Nut FRONT Mounting base (lower) 2. Fasten the bracket and mounting plate to the mounting base (upper) with 12 hex head bolts. Fasten the mounting plate at the rear for 9° tilt, or

Summary of the content on the page No. 11

3. Loosely screw six screws (M5X15) into the holes at the rear of the display unit. Set the screws on the display unit to the holes on the bracket and then tighten the screws. (Note that the display unit may also be mounted in portrait orientation.) Fastening the front panel 4. Fasten the power cable (local supply in case of AC power), cable from the control and operation sections of external equipment and ground wire (local supply) at the rear of the MU-150C. For use of the cable type

Summary of the content on the page No. 12

5. Grease the two hex head bolts for fastening the display unit to the mounting base (lower). 6. Fasten the display unit to the mounting base (lower) with the two hex head bolts greased at step 5. Hex Head Bolt Fastening the mounting base (lower) to the display unit 7. For portrait orientation, attach logo (supplied) at upper left hand corner. 5

Summary of the content on the page No. 13

1.1.1 Hood (option) A hood (portrait or landscape) is optionally available. Attach it to the display unit with Velcro tape as shown below. 1. Attach nine sets of Velcro tape to the display unit at the locations shown below, in as straight as possible. Attach Attach in line. in line. Display unit, how to attach Velcro tapes 2. Attach the hood to the display unit. 6

Summary of the content on the page No. 14

2 WIRING 2.1 Wiring External Equipment Connect external equipment to the MU-150C by referring to the drawings in this section. A cable with connector at both ends is provided to connect equipment. General-purpose monitor To use the MU-150C as a general-purpose monitor, connect equipment with a mini D-SUB 15P connector. In this case do not connect a navigator to the NMEA port. Nav data is output through the D-SUB 25P connector. CH-37: DISPLAY CH-250: INTERFACE UNIT RGB OUT FCV-120

Summary of the content on the page No. 15

Connecting FCV-1200 series and CH-250 Using the cables designated below (or equivalent) to connect the FCV-1200 series or CH-250 makes their interface unit of the FCV-1200 series and CH-250 unnecessary. The mini D-SUB 15 P connector cannot be used to connect the FCV-1200 series and CH-250. Navigator, etc. 06S4078 FCV-1200 Series: 24 VDC PROCESSOR UNIT CN1 or 100-240 VAC CH-250: TRANSCEIVER UNIT Ground DATA/VIDEO OUT Terminal FCV-1200 Series: CONTROL UNIT MJ-A10SPF0002-01

Summary of the content on the page No. 16

• Cable 06S4078 is of waterproof construction, however, the MU-150C is not waterproof (specification IPX0). Therefore, remove rubber cover and fixing metal from the display side of the cable. Remove fixing metal. Remove rubber cover. D-sub connector 9

Summary of the content on the page No. 17

3 ADJUSTMENTS Controls for adjustment of the picture are provided on the rear of the display unit. Open the small cover to access the controls. 12 3 GND 100-240 VAC POWER 2A 50-60 Hz S1 S2 S3 S4 R1 J16 EXTBRILL S1 SEL J17 BRILL S2 UP R2 J18 BRTP J16 J17 J18 S3 DOWN R1 R S4 RESET 131313 R2 G R3 R3 B DATA/VIDEO IN NMEA CONT Rear panel (AC type) 10

Summary of the content on the page No. 18

3.1 Picture Adjustment Contrast and picture are adjusted with [S1]: Opens menu; selects menu items. [S2]: Increases setting. [S3]: Decreases setting. [S4]: Initializes setting. Note: Though “EXIT” is printed on the CONE Board (10P6877), the function of S4 switch is “RESET.” [S1] Brilliance (Not used.) [S1] Contrast [S1] Size (horizontal size for landscape type, vertical size for portrait type) [S1] Geometry [S1] Center (vertical position for landscape type, horizontal position f

Summary of the content on the page No. 19

3.2 RGB Adjustment Color may be adjusted with the following potentiometers. Turn the potentiometers clockwise to increase color. Model Potentiometer Setting FCV-1200 Series, CH-250, Default setting FR-1760DS GD/GP-280/380/680, FCV-1500 Fully clockwise Series, CH-37, CSH23/73/83, FR-1500 MK3 Series R1: Red R2: Green R3: Blue 3.3 Brilliance Adjustment Brilliance can be adjusted from the control unit of the FCV-1200 series or CH-250 by setting jumper block J17 as below. J17:

Summary of the content on the page No. 20

4 OPERATION FURUNO LED BRILLIANCE Control POWER Switch Display unit POWER switch: Turns the power on/off. The LED lamp lights in green when the unit is turned on and goes off when the unit is turned off. To turn the MU-150C on and off from the control unit of a video sounder such as the FCV-1200 series, turn on the POWER switch of the MU-150C. Note that with the MU-150C turned on and the FCV-1200 turned off the LED on the MU-150C lights in red. This means that weak current is flowi


Alternative user manuals
# User manual Category Download
1 Furuno Black Box Searchlight Sonar CH-250BB User manual Computer Monitor 2
2 Furuno FEA-2107 User manual Computer Monitor 176
3 Furuno MU-201CE User manual Computer Monitor 28
4 Furuno SEARCHLIGHT SONAR CH-250 User manual Computer Monitor 22
5 Furuno FEA-2807 User manual Computer Monitor 126
6 Furuno RD-30 User manual Computer Monitor 212
7 Furuno LCD DISPLAY MU-155C User manual Computer Monitor 6
8 Furuno MU-231CE User manual Computer Monitor 50
9 Furuno PM30 User manual Computer Monitor 2
10 Sony BVM-L170 User manual Computer Monitor 7
11 Sony DDM-2802CNU User manual Computer Monitor 1
12 Sony BVM-D20F1U, BVM-D20F1E, BVM-D20F1A, BVM-D24E1WU, BVM-D24E1WE, BVM-D24E1WA, BVM-D32E1WU, BVM-D32E1WE, BVM-D32E1WA User manual Computer Monitor 15
13 Sony 500A3WE User manual Computer Monitor 8
14 Sony CPD-17SF2 User manual Computer Monitor 10
15 Sony AEP MODEL CPD-E200E User manual Computer Monitor 9