Summary of the content on the page No. 7
C H A P TER 2 C HAP TER 1INSTALLATION AND SETUP This chapter discusses how to install your CRT touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor Check that the following 6 items are present and in good condition: OR Serial cable USB cable CRT Touchmonitor Quick Installation Guide CD VGA cable Software Quick Installation Guide monitor power cord CD Software 2-3
Summary of the content on the page No. 8
Connecting Your Touchmonitor Important: Before connecting the cables to your touchmonitor and PC, be sure that the computer and touchmonitor are turned off. Removing the Back Cover Note: You will need a Phillips screwdriver to remove the back cover. In order to access the touchmonitor connections, unscrew the four screws on the back cover. Remove the back cover to expose the touchmonitor connections. Touchmonitor Connections Power Female 9-pin Female 15-pin video serial or USB connector to
Summary of the content on the page No. 9
Connect the Video Cable video cable Connect one end of the video cable to the video connector on your PC and the other end of the cable to the video connector on your monitor. Secure the cable by turning the thumbscrews on each connector. Connect the Serial or USB Touchscreen Cable serial or USB cable video cable Depending on your monitor, connect either the serial or USB touchscreen cable. Connect one end to the appropriate port on the back of your computer. Connect the other end of the
Summary of the content on the page No. 10
Connect the Power Cable power cable serial or USB cable video cable Connect the power cable to the AC connector on your touchmonitor. To protect your equipment against risk of damage from electrical surges in the power line, plug the touchmonitor’s power cord into a switched surge protector, and then connect the surge protector to a grounded (three-pronged) AC electrical outlet. 2-6 Elo Entuitive Tou chmon ito r User Guide
Summary of the content on the page No. 11
Attach the Back Cover When you have finished connecting your touchmonitor, bring the three cords together at the back of the monitor. Place the back cover on the back and pull the cords through the cut out of the back cover. Replace the four screws and tighten them securely. Be sure not to over tighten the screws. Your touchmonitor has no power switch. Power on your monitor using the power switch of the surge protector, and check that the power LED is on. If not, refer to Chapter 4
Summary of the content on the page No. 12
Installing the Driver Software Elo TouchSystems provides driver software that allows your touchmonitor to work with your computer. Drivers are located on the enclosed CD-ROM for the following operating systems: Windows XP Windows 2000 Windows Me Windows 98 Windows 95 Windows NT 4.0 Additional drivers and driver information for other operating systems are available on the Elo TouchSystems web site at www.elogaming.com. Your Elo touchmonitor is plug-and-play compliant. Information o
Summary of the content on the page No. 13
Installing the Touch Driver for Windows XP, Windows 1 2000 , Me, 95/98 and NT 4.0 Note: For Windows 2000 and NT 4.0 you must have administrator access rights to install the driver. 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the CD and starts the setup program. 2 Follow the directions on the screen to complete the driver setup for your version of Windows. If the AutoStart feature is not a
Summary of the content on the page No. 14
2 INSTALL asks you to select the software to install. Then choose d:\ EloDos_W31 from the displayed list. 3 INSTALL also asks you for the paths to use during installation, or you may use its defaults. INSTALL creates directories as necessary, and warns you if they exist. If you are updating your software, you may wish to specify the paths containing the earlier versions, and overwrite the obsolete files. All executable programs are upward compatible. For a list of differences from each previ
Summary of the content on the page No. 15
C H A P TER 3 C HAP TER 1OPERATION About Touchmonitor Adjustments By design, your Elo Entuitive touchmonitor should not require any adjustments. The factory settings will give you optimum video results with most standard PC video display adapters. However, after connecting your touchmonitor you can further optimize the settings to meet your requirements by following the directions in this chapter. All adjustments you make to the controls are automatically memorized, so you do not need to res
Summary of the content on the page No. 16
Touchmonitor Controls You can adjust the screen display by using the plastic knob labeled OSD located on the right-hand side of the monitor. Using the On Screen Display (OSD) 1 Push the OSD knob to access the OSD. 2 Turn the OSD knob to choose the item you want to adjust. The selected item is highlighted. See figure 3.1 for OSD menu options. 3 Push the OSD knob to adjust the highlighted item. The display unit automatically saves the new settings in about 45 seconds after your last adjustment
Summary of the content on the page No. 17
OSD Adjustments Symbol Function Process Adjusts the horizontal size of the entire screen image. H. Size Adjusts the horizontal position of the entire screen image. H. Position Adjusts the vertical size of the entire screen image. V. Size Adjusts the vertical position of the entire screen image. V. Position Simultaneously changes vertical and horizontal image size. Zoom See Figure 3.4, page 1-16. Geometry If the vertical sides of the picture curve in or bulge out, you can correct the distortion
Summary of the content on the page No. 18
Corrects vertical top and bottom linearity. C. Correct Clears vertical moire if a series of concentric circles or arcs appear on your screen. Note: Moire is an interface pattern that makes the screen seem to have faint lines. A picture that is rastered or consists of small repeating figures is sensitive to moire interference. Strong colors are also liable to intensify moire. The moire pattern on the screen does not affect the printout of the V. Moire image. Clears horizontal moire if a ser
Summary of the content on the page No. 19
If you have moved the display unit, you should perform demagnetization. Demagnetizing takes place automatically when the display unit is switched on, and the unit normally maintains faultless color purity during operation. If you have tilted, swiveled or moved the display unit, you can perform demagnetization. During the process the picture is distorted for a few seconds. After demagnetization, the color impurities have disappeared if caused by stray magnetic fields. Do not use the degaus
Summary of the content on the page No. 20
ESC Figure 1.4 3-16 Elo En tuitive Touc hmonitor User Gu ide
Summary of the content on the page No. 1
Summary of the content on the page No. 2
Elo Entuitive Touchmonitor User Guide For 15", 17" and 19" CRT Kiosk Series Touchmonitors ET1X45C-4SWE-1 Series Models ET1X45C-4UWE-1 Series Models Revision A P/N 008572 Elo TouchSystems, Inc. 1-800-ELOTOUCH www.elotouch.com www.elogaming.com
Summary of the content on the page No. 3
Copyright © 2003 Elo TouchSystems Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no
Summary of the content on the page No. 4
Table of Contents Preset Timing Table . . . . . . . . . . . . . . . 28 Chapter 1 Regulatory Information 29 Introduction 1 Precautions . . . . . . . . . . . . . . . . . . . . 1 Warranty 31 About the Product . . . . . . . . . . . . . . . . . 1 Index 33 Chapter 2 Installation and Setup 3 Unpacking Your Touchmonitor. . . . . . . . . . . 3 Connecting Your Touchmonitor . . . . . . . . . . 4 Removing the Back Cover . . . . . . .
Summary of the content on the page No. 5
C H A P TER 1 C HAPT ER 1INTRODUCTION Congratulations on your purchase of an Elo TouchSystems Entuitive touchmonitor. Your new high-resolution touchmonitor combines the reliable performance of Elo’s touch technology with the latest advances in CRT display design. This combination of features creates a natural flow of information between a user and the touchmonitor. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your
Summary of the content on the page No. 6
Patented iTouch technology from Elo TouchSystems. Either RS-232 serial or USB touch interface. Full sheetmetal enclosure adds protection and security. 1-2 Elo Entuitive Tou chmon ito r User Guide
