Summary of the content on the page No. 1
ELO Entuitive Touchmonitor
User Guide
For 15" and 17" CRT iTouch and AccuTouch Series
Touchmonitors
ET 1525C/1526C Series ET 1725C/1726C Series
Revision A
Summary of the content on the page No. 2
Elo Entuitive Touchmonitor User Guide For 15" and 17" CRT iTouch and AccuTouch Series Touchmonitors ETXX25C/26C-4XWE-3 Series Models ETXX25C/26C-7XWE-1 Series Models Revision A P/N 008553 Elo TouchSystems, Inc. 1-800-ELOTOUCH www.elotouch.com
Summary of the content on the page No. 3
Summary of the content on the page No. 4
Copyright © 2002 Elo TouchSystems Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no
Summary of the content on the page No. 5
iv
Summary of the content on the page No. 6
Table of Contents Chapter 1 Warranty 33 Introduction 1 Index 35 Precautions . . . . . . . . . . . . . . . . . . . . 1 About the Product . . . . . . . . . . . . . . . . . 1 Chapter 2 Installation and Setup 3 Unpacking Your Touchmonitor. . . . . . . . . . . 3 Installing the Base . . . . . . . . . . . . . . . 4 Uninstalling the Base. . . . . . . . . . . . . . 5 Selecting a Suitable Location . . . . . . . . . 5 Connecti
Summary of the content on the page No. 7
vi
Summary of the content on the page No. 8
C H A P TER 1 C HAPT ER 1INTRODUCTION Congratulations on your purchase of an Elo TouchSystems Entuitive touchmonitor. Your new high-resolution touchmonitor combines the reliable performance of Elo’s touch technology with the latest advances in CRT display design. This combination of features creates a natural flow of information between a user and the touchmonitor. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your
Summary of the content on the page No. 9
1-2 Elo Entuitive Tou chmon ito r User Guide
Summary of the content on the page No. 10
C H A P TER 2 C HAP TER 2INSTALLATION AND SETUP This chapter discusses how to install your CRT touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor Check that the following 8 items are present and in good condition: CD (with e-manual) Base and Quick Installation Guide VGA cable European power cable OR USA power cable Serial cable USB cable 2-3
Summary of the content on the page No. 11
Installing the Base Carefully turn the touchmonitor upside-down. Place the base against the bottom of the monitor so that the base fasteners are aligned with appropriate slots. Push the base towards the front of the monitor until you hear a “click” and the latch locks into position. Carefully turn the touchmonitor right-side up. 2-4 Elo Entuitive Tou chmon ito r User Guide
Summary of the content on the page No. 12
Uninstalling the Base Carefully turn the touchmonitor upside-down. Gently press the clip with one hand while pulling the base towards the r ear of the cabinet with the other hand. Carefully turn the touchmonitor right-side up. Selecting a Suitable Location Place the monitor at least 12 inches from other electrical or heat-emitting equipment and allow at least 4 inches on each side for ventilation. Place the monitor in a position where no light shines or is reflected directly on the
Summary of the content on the page No. 13
Summary of the content on the page No. 14
2 Connect the power cable to the AC connector on your touchmonitor. To protect your equipment against risk of damage from electrical surges in the power line, plug the touchmonitor’s power cord into a surge protector, and then connect the surge protector to a grounded (three-pronged) AC electrical outlet. 3 Connect the touchscreen cable. Determine if you have RS-232 or USB. Connect one end to the appropriate port on the back of your PC. Connect the other end of the cable to the touchscreen
Summary of the content on the page No. 15
Soft Power Switch Power LED 4 Power on your monitor using the Soft power switch and check that the power LED is on, then power on your PC. If not, repeat steps 2, 3, and 4, or refer to Chapter 4, Troubleshooting. 5 After a brief pause the picture should appear. If necessary, adjust the front panel controls according to your personal preference (see Chapter 3). 6 Insert the Elo TouchTools CD-ROM in your computer’s CD-ROM drive to install the appropriate touchscreen driver software. Follow th
Summary of the content on the page No. 16
Installing the Driver Software Elo TouchSystems provides driver software that allows your touchmonitor to work with your computer. Drivers are located on the enclosed CD-ROM for the following operating systems: Windows XP Windows 2000 Windows Me Windows 98 Windows 95 Windows NT 4.0 Additional drivers and driver information for other operating systems are available on the Elo TouchSystems web site at www.elotouch.com. Your Elo touchmonitor is plug-and-play compliant. Information on
Summary of the content on the page No. 17
Installing the Serial Touch Driver for Windows XP, 1 Windows 2000 , Me, 95/98 and NT 4.0 NOTE: For Windows 2000 and NT 4.0 you must have administrator access rights to install the driver. 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the CD and starts the setup program. 2 Follow the directions on the screen to complete the driver setup for your version of Windows. If the AutoStart feature is
Summary of the content on the page No. 18
Installing the Touch Driver for MS-DOS and Windows 3.1 You must have a DOS mouse driver (MOUSE.COM) installed for your mouse if you wish to continue using your mouse along with your touchmonitor in DOS. To install Windows 3.x and MS-DOS from Windows 95/98, follow the directions below: 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. 2 From DOS, type d:\EloDos_W31 to change to the correct directory on the CD-ROM (your CD-ROM drive may be mapped to a different drive letter). 3 Type
Summary of the content on the page No. 19
2-12 Elo En tuitive Touchmonitor User Gu ide
Summary of the content on the page No. 20
C H A P TER 3 C HAP TER 3OPERATION About Touchmonitor Adjustments By design, your Elo Entuitive touchmonitor should not require any adjustments. The factory settings will give you optimum video results with most standard PC video display adapters. However, after connecting your touchmonitor you can further optimize the settings to meet your requirements by following the directions in this chapter. All adjustments you make to the controls are automatically memorized, so you do not need to res
