Summary of the content on the page No. 1
Summary of the content on the page No. 2
Elo Entuitive Touchmonitor User Guide 17" LCD Desktop Touchmonitor 1724L Series Revision A P/N 008561 Elo TouchSystems, Inc. 1-800-ELOTOUCH www.elotouch.com
Summary of the content on the page No. 3
Summary of the content on the page No. 4
Copyright © 2002 Elo TouchSystems Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no
Summary of the content on the page No. 5
iv
Summary of the content on the page No. 6
Table of Contents H/VPOSITION . . . . . . . . . . . . . . 20 Chapter 1 H-POSITION. . . . . . . . . . . . . . . . . 20 Introduction 1 V-POSITION. . . . . . . . . . . . . . . . . 20 Product Description . . . . . . . . . . . . . . . . 1 CLOCK PHASE . . . . . . . . . . . . . 20 Precautions . . . . . . . . . . . . . . . . . . . . 1 PHASE . . . . . . . . . . . . . . . . . . . 20 About the
Summary of the content on the page No. 7
Copyright © 1996, Borland International. All rights reserved. BORLAND CONFIDENTIAL June 11, 2002 10:05 am (D:\Vera new\8561-17 LCD Econ Hyundai\1724L Econ Hyundai DesktopTOC.fm) vi
Summary of the content on the page No. 8
C H A P TER 1 C HAPT ER 1INTRODUCTION Product Description Congratulations on your purchase of an Elo TouchSystems Entuitive LCD desktop touchmonitor. Your new high-resolution industrial touchmonitor combines the reliable performance of Elo’s touch technology with the latest advances in LCD display design. This combination of features creates a natural flow of information between you and your touchmonitor. Precautions Follow all warnings, precautions and maintenance as recommended in this us
Summary of the content on the page No. 9
Plug & Play High quality full screen re-scaling VESA DDC 1/2B data communication VESA DPMS power saving Supports VESA Flat Panel Monitor Physical Mounting Interface Worldwide agency approvals that include UL, CUL, TÜV- Bauart, FCC, CE, C-Tick, VCCI IntelliTouch or AccuTouch Technology For full Product Specifications refer to Appendix C. 1-2 Elo Entuitive Tou chmon ito r User Guide
Summary of the content on the page No. 10
C H A P TER 2 C HAP TER 2INSTALLATION AND SETUP This chapter discusses how to setup your LCD desktop touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor US power cord European power cord Video cable CD and Quick Serial touchscreen AC/DC Power adapter Installation Guide cable 2-3
Summary of the content on the page No. 11
Rear View 2-4 Elo Entuitive Tou chmon ito r User Guide
Summary of the content on the page No. 12
Connecting Your Touchmonitor Before connecting the cables to your touchmonitor and computer, be sure that the touchmonitor and computer are off. Video Cable Connection Connections on underside Female 15-pin video D-SUB Video Video port cable Ferrite bead 1 Set the touchmonitor on a solid horizontal surface, such as a table or desk. 2 Connect the female end of the video cable connector to the back of the LCD monitor, and connect the other end to the back of the computer. 3 Secure the cable to y
Summary of the content on the page No. 13
Touchscreen Cable Connection Connections on underside Female 9-pin serial touchscreen connector Serial touchscreen cable 1 Connect the female end of the 9-pin touchscreen RS-232 cable to the serial port on the back of your computer. 2 Connect the male end of the cable to the serial touchscreen connector on your touchmonitor. 3 Secure the cable to your touchmonitor and computer by tightening the screws on the connector clockwise. 2-6 Elo Entuitive Tou chmon ito r User Guide
Summary of the content on the page No. 14
Power Cable Connection Connections on underside DC 12V Brick power cable port Power cable Brick power supply 1 Depending on where you live, you will use either the European or US/Canadian power cable. Connect the female end of the power cable to the Brick power supply. 2 Connect the Brick power supply into the power port on the touchmonitor. To protect your equipment against risk of damage from electrical surges in the power line, plug the Brick supply’s power cord into a surge protector, an
Summary of the content on the page No. 15
Video Input Pin Assignment This section describes the pin assignment of the LCD’s 15 Pin Mini D-sub (video cable) connector. Pin No. Signal Connector 1 Red Video Signal 2 Green Video Signal 3 Blue Video Signal 4 N.C. 5 Ground 6 Ground for red video signal 7 Ground for green video signal 8 Ground for blue video signal 9 N.C. 10 Ground 11 N.C. 12 DDC data 13 Horizontal sync signal 14 Vertical sync signal 15 DDC clock 2-8 Elo Entuitive Tou chmon ito r User Guide
Summary of the content on the page No. 16
Installing the Driver Software The driver software allows your touchmonitor to work with your computer. Drivers are located on the enclosed CD-ROM for the following operating systems: Windows XP Windows 2000 Windows Me Windows 98 Windows 95 Windows NT 4.0 Your touchmonitor is plug-and-play compliant. Information on the video capabilities of your touchmonitor is sent to your video display adapter when Windows starts. If Windows detects your touchmonitor, follow the instructions o
Summary of the content on the page No. 17
Installing the Serial Touch Driver for Windows XP, 1 Windows 2000 , Me, 95/98 and NT 4.0 NOTE: For Windows 2000 and NT 4.0 you must have administrator access rights to install the driver. 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the CD and starts the setup program. 2 Follow the directions on the screen to complete the driver setup for your version of Windows. If the AutoStart feature i
Summary of the content on the page No. 18
Installing the Serial Touch Driver for MS-DOS and Windows 3.1 You must have a DOS mouse driver (MOUSE.COM) installed for your mouse if you wish to continue using your mouse along with your touchmonitor in DOS. To install Windows 3.x and MS-DOS from Windows 95/98, follow the directions below: 1 Insert the CD-ROM in your computer’s CD-ROM drive. 2 From DOS, type d:\EloDos_W31 to change to the correct directory on the CD-ROM (your CD-ROM drive may be mapped to a different drive letter). 3 Ty
Summary of the content on the page No. 19
2-12 Elo En tuitive Touchmonitor User Gu ide
Summary of the content on the page No. 20
C H A P TER 3 C HAP TER 3OPERATION Variations in video output and application will likely require you to adjust your touchmonitor to optimize the quality of the display. For best performance, your monitor should be operating in native resolution; that is, 1280 x 1024 at 60 Hz. Use the Display control panel in Windows to choose 1280 x 1024 resolution. Operating in other resolutions will degrade video performance. For further information, please refer to Appendix A. All adjustments you make to
