Summary of the content on the page No. 1
Elo Entuitive Touchmonitor
User Guide
For 15” and 17” CRT Rear Mount
Touchmonitors
Version 1.0
DOC# SW500127
P/N 008527
ET1545C Series Models
ET1745C Series Models
Elo TouchSystems, Inc.
1-800-ELOTOUCH
www.elotouch.com
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Copyright © 2000 Elo TouchSystems Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not lim- ited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes n
Summary of the content on the page No. 4
iv-Elo Entuitive Touchmonitor CRT Desktop User Guide
Summary of the content on the page No. 5
Contents Chapter 1. Introduction ........................................................................1 Precautions................................................................................................1 About the Product .....................................................................................1 Chapter 2. Installation and Setup ........................................................3 Unpacking Your Touchmonitor..........................................................
Summary of the content on the page No. 6
Contents Appendix C. Technical Specifications..................................................29 Touchmonitor Specifications...................................................................30 IntelliTouch Touchmonitor Specifications ..............................................32 AccuTouch Touchmonitor Specifications ...............................................34 Signal PINOUT for 15” and 17” Monitors ..........................................36 Power Consumption........................
Summary of the content on the page No. 7
Precautions Chapter 1 Introduction Congratulations on your purchase of an Elo TouchSystems Entuitive touchmonitor. Your new high-resolution touchmonitor combines the reliable performance of Elo’s touch technology with the latest advances in CRT display design. This combination of features creates a natural flow of information between a user and the touchmonitor. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Se
Summary of the content on the page No. 8
Chapter 1 : Introduction 2 - Elo Entuitive Touchmonitor CRT Rear Mount User Guide
Summary of the content on the page No. 9
Unpacking Your Touchmonitor Chapter 2 Installation and Setup This chapter discusses how to install your CRT touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor Check that the following 7 items are present and in good condition: Monitor power cable CRT Rear Mount monitor with tethered video cable Mounting L-brackets (2) Elo QuickStart CD OR Software User Guide USB touchscreen cable Serial touchscreen cable User’s Guide, Quick Start Guide, and TouchTool
Summary of the content on the page No. 10
Chapter 2 : Installation and Setup Getting Started Selecting a Suitable Location ❑ Place the monitor at least 12 inches from other electrical or heat-emitting equipment and allow at least 4 inches on each side for ventilation. ❑ Place the monitor in a position where no light shines or is reflected directly on the screen. ❑ To reduce eye strain, avoid installing the monitor unit against a bright background such as a window. ❑ Position the monitor so the top of the screen is no higher than eye le
Summary of the content on the page No. 11
Mounting Your Touchmonitor Mounting Your Touchmonitor Your Elo touchmonitor is designed to be mounted in a variety of ways. The mounting brackets enable you to mount your touchmonitor horizon- tally or vertically. You can also use the keyholes on the bottom of the monitor for slide-in-place mounting. See Appendix C for dimension drawings of all mounting options. Note: You will need a Phillips screwdriver to attach the L-brackets. Your touchmonitor comes with two L-brackets (and four screws) that
Summary of the content on the page No. 12
Chapter 2 : Installation and Setup Vertical Mount To mount the brackets vertically to your touchmonitor: 1. Locate the two holes on each side of your touchmonitor. Match up the two holes of one bracket to the holes on one side of your touchmonitor. L-bracket 2. Place two screws in the holes and with the screwdriver, screw them in to secure the bracket. 3. Repeat steps 1 and 2 to attach the other L-bracket to the other side of the touchmonitor. Bottom Mount You can also mount your touchmonito
Summary of the content on the page No. 13
Connecting Your Touchmonitor Connecting Your Touchmonitor Your touchmonitor comes with one of the following touchscreen con- nector cables: Serial (RS-232) or USB cable (for Windows 98 and Win- dows 2000 systems only). IMPORTANT: Before connecting the cables to your touchmonitor and PC, be sure that the computer and touchmonitor are turned off. 1. Connect the video cable to the video connector on your PC. Secure the cable to your PC by turning the screws on the con- nector. Tethered video cabl
Summary of the content on the page No. 14
Chapter 2 : Installation and Setup 2. Connect the power cable to the AC connector on your touch- monitor. To protect your equipment against risk of damage from electrical surges in the power line, plug the touchmonitor’s power cord into a surge protector, and then connect the surge protector to a grounded (three-pronged) AC electrical outlet. Power cable Tethered video cable 8 - Elo Entuitive Touchmonitor CRT Rear Mount User Guide
Summary of the content on the page No. 15
Connecting Your Touchmonitor 3. Connect the touchscreen cable. Determine if you have RS-232 or USB. Connect one end to the appropriate port on the back of your PC. Connect the other end of the cable to the touchscreen connector on your touchmonitor. Secure the serial cable to your touchmonitor and PC by turning the screws on the connector. The USB cable connectors should fit snugly into the connectors on your PC and touchmonitor. Power cable Tethered video cable Serial touchscreen cable OR Po
Summary of the content on the page No. 16
Chapter 2 : Installation and Setup 4. The OSD controls and the Soft Power switch are located on a panel inside the bottom of your monitor. Power on your monitor using the Soft power switch and check that the power LED is on, then power on your PC. If the LED is not on, repeat steps 2, 3, and 4, or refer to Chapter 4, Troubleshooting. Underside view of the touchmonitor Menu Brightness Power LED Select Contrast Soft Power Switch 5. After a brief pause the picture should appear. If necessary, adj
Summary of the content on the page No. 17
Installing the Driver Software Installing the Driver Software Elo TouchSystems provides driver software that allows your touchmoni- tor to work with your computer. Drivers are located on the enclosed CD- ROM for the following operating systems: ❑ Windows 2000 ❑ Windows 98 ❑ Windows 95 ❑ Windows NT 4.0 Additional drivers and driver information for other operating systems (including MS DOS, Windows 3.x, OS/2, Macintosh and Linux) are available on the Elo TouchSystems web site at www.elotouch.com.
Summary of the content on the page No. 18
Chapter 2 : Installation and Setup 2. Click the Browse button to locate the EloCd.exe program on the CD-ROM. 3. Click Open, then OK to run EloCd.exe. 4. Follow the directions on the screen to complete the driver setup for your version of Windows. Installing the USB Touch Driver for Windows 2000 and Windows 98 1. Insert the Elo CD-ROM in your computer’s CD-ROM drive. If Windows 98 or Windows 2000 starts the Add New Hardware Wizard: 2. Choose Next. Select “Search for the best driver for you
Summary of the content on the page No. 19
Installing the Driver Software 2. Click the Browse button to locate the EloCd.exe program on the CD-ROM. 3. Click Open, then OK to run EloCd.exe. 4. Follow the directions on the screen to complete the driver setup for your version of Windows. Elo Entuitive Touchmonitor CRT Rear Mount User Guide - 13
Summary of the content on the page No. 20
Chapter 2 : Installation and Setup 14 - Elo Entuitive Touchmonitor CRT Rear Mount User Guide
