Summary of the content on the page No. 1
For Microsoft Windows CE 2.12
Version E
Touch Panel
LCD Monitor integrated
Windows-based Terminal
Please confirm the version of the software built in eClient, and refer to
the suited User's Manual (Refer to the User's Manual Version List on
next page).
This is the manual for the following software version.
* Microsoft Windows CE: 2.12 Rev.1.64 or later
* Microsoft Terminal Server Client: Ver.6.60 or later
* ICA Client: Ver.6.20 [Build 992] or later
Summary of the content on the page No. 2
User’s Manual Version List A handling description changes with versions of the software built in eClient. Please refer to below. NOTE • The version of software built in eClient can be checked with a [System]-[ICA] tab of [Terminal Properties]. OS: Microsoft Windows CE 2.12 Software Microsoft ICA Client Microsoft Windows CE Windows Software Manual Terminal Server E Version 6.20 2.12 Rev.1.64 or later Version 6.60 or later (This Manual) [Build992] or later Version 6.20 D 2.12
Summary of the content on the page No. 3
SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety. Copyright© 2002-2003 EIZO NANAO CORPORATION All rig
Summary of the content on the page No. 4
TABLE OF CONTENTS 1. INTRODUCTION..................................................................................... 6 1-1. General Description ......................................................................................6 1-2. Features ........................................................................................................7 1-3. Package Contents..........................................................................................7 1-4. Controls & Connectors .
Summary of the content on the page No. 5
INDEX......................................................................................................121 TABLE OF CONTENTS 5
Summary of the content on the page No. 6
English 1. INTRODUCTION Thank you very much for purchasing the EIZO eClient 630LT-GR. 1-1. General Description The 630LT-GR is a terminal which displays applications on a Windows Terminal Server (WTS) or a web site and conveys input by a keyboard or a mouse to the WTS. To operate the 630LT-GR, please connect it to a WTS with Microsoft Window NT Terminal Server Edition or Windows 2000 Server / Advanced Server / Datacenter Server. Windows Terminal Server (WTS) 630LT-GR Output
Summary of the content on the page No. 7
English 1-2. Features • Lower TCO* *TCO (Total Cost of Ownership) Expense for managing and administrating computer systems. • Saves Space and Power Consumption • Less Heat, Less Noise • Serial Port for Modem/PDA (*Hayes AT Compatible Modem Supported) • Speakers Equipped • PC card Slot for Modem Card, LAN Card, and Wireless LAN Card • 2 USB Downstream Ports for USB HID Mouse and Keyboard • Local Web Browser Added as a Default Connection • Wake on LAN Supported *Wake on LAN Wake
Summary of the content on the page No. 8
English 1-4. Controls & Connectors Front (4) (3) (2) (1) (1) Power Switch (2) Power Indicator Green Operation Screen saver mode Yellow Power save mode Off Power off (Wake on LAN standby ) NOTE • When turning off/on the unit, leave the unit off for a few seconds before turning it on again. (3) Volume (4) Speakers 8 1. INTRODUCTION
Summary of the content on the page No. 9
English Rear (16) (14) (17) (15) (13) (10) (12) (6) (8) (11) (5) (7) (9) (5) Mouse Connector (6) Keyboard Connector (7) Serial Port (RS-232C) (8) Parallel Connector (9) Power Connector (10) Ethernet Connector (10 Base-T, 100 Base-TX) (11) Headphone Connector (12) Microphone Connector (13) USB Port (Downstream) x 2 (14) PC Card Slot 1 (15) Security Lock* 2 (16) Holes for Mounting an Arm Stand* (17) Stand 1 * This allows for connection of a security cable. This lock supports
Summary of the content on the page No. 10
English 1-5. Overview Directions for the 630LT-GR’s Setup 2. CONNECTING THE 630LT-GR p.11 3. SETTING UP THE 630LT-GR 3-1. WBT Setup Wizard p.14 3-2. Connection p.32 3-3. Dial-Up Connection p.39 4. ADDING & CHANGING A CONNETION NAME 4-1. Adding a Connection Name p.46 4-2. Deleting a Connection p.63 4-3. Editing a Connection p.64 4-4. Setting an Autostart Connection p.67 Directions for the 630LT-GR’s Operation. 5. LOGON & LOGOFF 5-1. Logon to a WTS / Logoff from a WTS p.68
Summary of the content on the page No. 11
English 2. CONNECTING THE 630LT-GR This chapter shows how to connect the 630LT-GR to a WTS. 2-1. Setting up the 630LT-GR Please observe the following cautions when connecting the 630LT-GR. WARNING Place the 630LT-GR on a strong, stable surface. A unit placed on an inadequate surface may fall, resulting in injury or equipment damage. If the unit falls, disconnect the power immediately and have the unit checked by a qualified service engineer before using it again. Using a unit
Summary of the content on the page No. 12
English 2-2. Connecting the 630LT-GR NOTE • Before connecting the 630LT-GR, confirm the following: • The 630LT-GR is turned off. • The WTS is turned on. • Connect the peripherals to the appropriate connectors of the unit. 1. In case of connecting the WTS through LAN: Connect the 630LT-GR to the network with an ethernet cable. In case of a dial-up or dial-in connection: Connect the 630LT-GR to a modem or a modem card. NOTE • If using a LAN card for the connection, Please Inse
Summary of the content on the page No. 13
English 3. Plug the power cord into the power connector. WARNING Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may cause in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may cause in fire or electric shock. 2. CONNECTING THE 630LT-GR 13
Summary of the content on the page No. 14
English 3. SETTING UP THE 630LT-GR This chapter presents how to prepare for a connection with a WTS when the 630LT-GR starts up for the first time. 3-1. WBT Setup Wizard 1. Turn on the power switch. The power indicator turns green. NOTE • When no picture is displayed, or when the following message is shown on the screen, please refer to “8. Troubleshooting” on page 113. - Message - In use of a stylus or a finger as an input device, “No Mouse Connected!!” caution doe
Summary of the content on the page No. 15
English 2. “Touch panel calibration” is displayed. Five targets are displayed on the screen. Press the targets with a stylus or a fingertip to locate the center of the touch panel. If you accidentally touched the screen in the wrong spot during calibration, you will distort the touch panel calibration. 3. “Calibration measured” window is displayed when you finished. Click the “Enter” key to accept the settings. 3. SETTING UP THE 630LT-GR 15
Summary of the content on the page No. 16
English 4. “WBT Setup Wizard” is displayed. Click [Next>]. 5. End User License Agreement page is displayed. Read the content and click [Accept] to continue. 16 3. SETTING UP THE 630LT-GR
Summary of the content on the page No. 17
English 6. IP address setting page is displayed. [Yes, use the IP information supplied by DHCP.] ...................................Select this when using DHCP service. All the necessary information of the 630LT-GR including the IP address will be obtained by the DHCP. [No, I will enter static IP information.] ...................................Select this when not using DHCP service. Enter the IP address of the 630LT-GR. If DHCP service is not in operation, following message a
Summary of the content on the page No. 18
English 7. IP address page is displayed. [IP Address] ........................Type the IP address of the unit. [Subnet Mask].....................Type the subnet mask of the network. [Gateway] ...........................Type IP address of the Gateway machine if necessary. Click [Next>] when finished. 18 3. SETTING UP THE 630LT-GR
Summary of the content on the page No. 19
English 8. DNS and WINS setting page is displayed. This check box should be marked when DNS or WINS is used. NOTE • Skip the page by clicking [Next>] if DNS or WINS is not used. If using DNS Click the [Enable DNS] check box to activate this box. [Default Domain Name] .....Type the default domain name. [Primary Server IP]..............Type the DNS primary Server IP address. [Secondary Server IP]..........Type the DNS secondary Server IP address. If using WINS Click the [Enable
Summary of the content on the page No. 20
English 9. Desktop area resolution and color settings page is displayed. Select the preferable display mode from the two available modes: · 1024 x 768 (256 colors) · 1024 x 768 (65,536 colors) Click [Next>] when finished. 20 3. SETTING UP THE 630LT-GR
