Summary of the content on the page No. 1
SyncMaster TC190, TC240
LCD MONITOR
quick start guide
Summary of the content on the page No. 2
1 Installing the Product 1-1 Package Contents • Unpack the product and check if all of the following contents have been included. • Store the packaging box in case you need to move the Product at a later stage. Monitor CONTENTS Installation Manual Product Warranty User Manual Power Cord OPTIONAL PARTS Keyboard (USB) Mouse (USB) D-Sub Cable 1-2 Installing the Stand Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
Summary of the content on the page No. 3
Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product is facing downwards. Do not remove the stopper pin before installing the base. Hold the main body of the product with your hand as shown by the figure. Insert the stand base into the stand connection part in the direction shown in the figure. Turn the connecting screw at the bottom of the stand fully so that it is completely fixed.
Summary of the content on the page No. 4
After the installation of the base, stand the monitor up as shown in the figure. Now you can remove the stopper pin to adjust the stand. - Caution Avoid lifting the product holding only the stand. Disassembly is in the reverse order of assembly. 1-3 Installing a Wall Mount Before installation, disassemble the product according to the following steps.
Summary of the content on the page No. 5
Lift up the monitor stand to the maximum angle with your left hand, and remove the back decoration cover with your right hand, as shown in the figure. Remove the two screws(A). Remove the stand arm in the direction shown in the figure. This product provides a wall mount of 100 mm x 100 mm(200 mm x 100 mm) that complies with the VESA specifications. 100 mm x 100 mm 200 mm x 100 mm A. Wall Mount Base B. Wall Mount Kit (Optional) 1. Turn the product off and unplug the power cord from the wall outl
Summary of the content on the page No. 6
•If you use a screw that is longer than the standard specifications, the inside of the product may be damaged. •For wall mounts that are not compatible with the standard VESA specifications, the length of the screw may differ depending on the corresponding specifications. •Do not use screws that are incompatible with the standard VESA specifications and do not assemble them using excessive force. This may result in damage to the product or injury due to the product falling. Samsung shall not
Summary of the content on the page No. 7
1-5 Connecting Power Connect one end of the power cord to the POWER port of the product and connect the other end of the power cord to a 220V or 110V wall outlet. (The input voltage is switched automatically.)
Summary of the content on the page No. 8
1-6 Connecting to another Monitor Connect between the [VIDEO OUT] port on the product and the D-Sub port on your monitor using a D-Sub cable. Connect to the [VIDEO OUT] port to display the same picture on another monitor. (For presentation purposes)
Summary of the content on the page No. 9
1-7 Connecting a SERIAL Cable Devices which support RS-232C connection (interface) can be connected.
Summary of the content on the page No. 10
1-8 Connecting to your Printer Devices which support D-SUB 25-pin connection (interface) can be connected.
Summary of the content on the page No. 11
1-9 Connecting with a PC Connect the [RGB IN] port of the product to the [D-Sub] port of your PC with a D-Sub cable. Use the [RGB IN] port to directly connect the monitor to a PC.
Summary of the content on the page No. 12
1-10 Connecting a Stereo Cable Connect the [AUDIO IN] port on the rear side of the monitor to the sound card of the PC.
Summary of the content on the page No. 13
1-11 Connecting USB The USB port of the monitor supports Full-Speed Certified USB 2.0. Connect USB devices such as a mouse, keyboard and external storage devices (DSC (Digital Still Camera), MP3, external storage, etc.). You can use a USB device such as a mouse, keyboard, Memory Stick, or external hard disk drive by connecting them to the USB port of the monitor without connecting them to the PC.
Summary of the content on the page No. 14
1-12 Connecting Headphones Connect your headphones to the Headphone connection terminal. You may connect your headphones to the monitor.
Summary of the content on the page No. 15
1-13 Connecting MIC Connect the microphone cable to the MIC port on the monitor. You may connect your microphone to the monitor.
Summary of the content on the page No. 16
1-14 Kensington Lock A Kensington Lock is an anti-theft device that enables users to lock the product so that they can safely use it in public locations. Since the shape and usage of the locking device may differ depending on the model and the manufacturer, for more information, refer to the User Manual supplied with the locking device. You have to purchase an additional locking device. Locking the product 1. Insert the locking part of the locking device into the hole of the Kensington lock of
Summary of the content on the page No. 17
2 Troubleshooting 2-1 Monitor Self-Diagnosis • You can check if the product is working properly using the Self-Diagnosis function. • If a blank screen is displayed and the Power LED blinks even if the product and the PC are properly connected, perform the self-diagnosis function according to the procedures below. 1. Turn the product and the PC off. 2. Separate the signal cable from the product. 3. Turn the product on. 4. If the product is working properly, the mess
Summary of the content on the page No. 18
The display area suddenly moves to an edge or to the center. Did you change the graphics card or the driver? Please press the [AUTO] button to run the auto adjustment function. Did you change the resolution and frequency appropriate to Set the resolution and the frequency to the appropriate values the product? in the graphics card Refer to the (Standard Signal Mode Table) Is the graphics card configured correctly? Set up the graphics card referring to the user manual. The pictures are out-o
Summary of the content on the page No. 19
2-3 FAQ FAQ! Please try the following! How can I change the frequency of the video signal? You have to change the frequency of the graphics card. (For more information, refer to the User Manual of the com- puter or the graphics card.) How can I change the resolution? Windows XP : Change the resolution by selecting Control Panel → Appearance and Themes → Display → Settings. Windows ME/2000 : Change the resolution by selecting Con- trol Panel → Display → Settings. (For more information, refer t
